Philips SRU1060/10 User manual

SRU1060
Quick, Clean & Easy Setup
www.philips.com/urc
Instructions for use 4
Instructions pour l’utilisation 12
Modo de empleo 20
Bedienungsanleitung 28
Gebruiksaanwijzing 36
Istruzioni per l’uso 44
Instruções de uso 52
Bruksanvisning 60
Vejledning 68
Bruksanvisning 76
Käyttöohje 84
FIN
N
DK
S
P
I
NL
D
E
F
GB
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 1

3
1
3
4
5
6
7
8
9
0
2
*
(
)
¡
™
£
&
^
%
$
#
@
!
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 3

Contents
1. Introduction......................................................................................................4
2. Installing the remote control....................................................................4-8
Replacing the battery.......................................................................................................4-5
Testing the remote control...............................................................................................5
Setting the remote control...........................................................................................6-8
3. Keys and functions ..........................................................................................9
4. Restoring the original functions of your remote control....................10
5. Troubleshooting.......................................................................................10-11
6. Need help?......................................................................................................11
Code list of all brands / equipment................................................................92-105
Information to the Consumer...................................................................................106
1. Introduction
Congratulations on your purchase of the Philips SRU1060 universal remote
control. After installing the remote control you can operate a TV and a
DVD player/recorder with it.
You can find information about how to prepare this remote control for use
in the chapter ‘Installing the remote control’.
2. Installing the remote control
•A battery is already placed in the battery compartment of the
SRU1060. Just remove the protective foil from the battery and the
SRU1060 is ready for use.
Replacing the battery
The SRU1060 comes with one spare battery in the packaging.
1Press the little latch on the right hand side
of the battery compartment
Keep the latch pressed and slide the
compartment outwards.
4ENGLISH
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 4

2Place the spare CR2025 Lithium battery
into the battery compartment, as shown.
Make sure to place the text side of the
battery upwards.
3Slide the cover back and click it firmly
into place.
Note: If the LED blinks four times after every key press, the remote control is
indicating that its battery is running low. Replace the old battery with a
CR2025 Lithium battery.
Testing the remote control
The remote control has been programmed to operate most Philips brands.
Because the SRU1060 may use different signals for each brand and even for
different models of the same make, it is advisable to test whether your
brand responds to the SRU1060.
The example below (TV) instructs you how to do this.
You can repeat the same steps for your DVD player/recorder which you
want to operate using the SRU1060.
Example of TV:
1Turn your TV on manually or use the original remote control.
Tune to channel 1.
2Check whether all the keys are working.
For an overview of the keys and their
functions see ‘3. Keys and functions’.
–If the TV responds as it should to all of the
key commands the SRU1060 is ready for
use.
If the LED does not light up, check whether the battery has been
properly inserted.
See ‘Inserting the battery’.
•If the device does not respond at all or not to all of the key
commands, follow the instructions under ‘Setting the remote
control’, or for online setup go to: www.philips.com/urc.
5ENGLISH
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 5

Setting the remote control
This is only necessary if your brand does not respond to the SRU1060.
If that is the case, the SRU1060 does not recognize the brand and/or
model of your brand and you need to program the remote control to do
so.
The example below (TV) instructs you how to do this.
You can repeat the same steps when setting the SRU1060 for your
DVD player/recorder.
You can set the remote control either automatically or manually.
Automatically setting the remote control
The remote control will now automatically search for the right code for
your brand.
Example of TV:
The keys between brackets are used for setting the SRU1060 for your
DVD player/recorder.
1Make sure the TV is switched on and select a channel using the
original remote control or the keys on the TV
(for example channel 1).The SRU1060 emits the ‘switch off TV’ signal
for all models of TV that are stored in the memory.
•If the device is a DVD player/recorder, insert a disk and start playback.
2Then keep keys VOL + and PROG +
(5and 6) on the SRU1060 pressed
simultaneously for three seconds,until the
LED flashes twice and then remains lit.
3Press and hold the TV (DVD) key of
the SRU1060.
6ENGLISH
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 6

– The SRU1060 now starts emitting all known . . . . . . . . . . . . . . . . . . . . . .
‘TV off’ signals, one by one.
Each time a code is sent, the LED lights up.
5When your TV switches off (stand-by), release the TV (DVD) key of
the SRU1060 immediately.
–The SRU1060 has now found a code that works on your TV.
6Check if you can operate all functions on your TV with the SRU1060.
•If this is not the case, you can redo the automatic setting.
The SRU1060 will then search for a code that works better.
–After the SRU1060 has run through all the known codes, the search
will stop automatically and the LED stops flashing.
–Automatic programming of a TV takes a maximum of 5 minutes.
For DVD this time is 2 minutes.
Manually setting the remote control
Example of TV:
The keys between brackets are used for setting the SRU1060 for your
DVD players/recorder.
1Turn on the TV manually or use the original remote control.
Tune in to channel 1.
2Look up the code of your TV in the
code list at the back of this manual.
7ENGLISH
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 7

The code exists of a combination of 5 keys
(always the cursor keys and the OK key in
various combinations). E.g. 1, OK, 3, OK, 4.
One or more codes are shown for each
brand. Note the first code.
Be careful! There are separate tables for TV,
and DVD.
On our website www.philips.com/urc you can directly select your device
typenumber to find the right code.
Make sure you use the codes from the correct table.
3Keep keys VOL + and PROG +
(5and 6) on the SRU1060 pressed
simultaneously for three seconds until the
LED flashes twice and then remains lit.
4Then enter the code noted in step 2
using the 1,2,3,4and OK keys.
–The LED will now flash twice. If the LED
flashes once for an extended period, the
code has not been entered properly or the
wrong code has been entered.
Start again from step 2.
5Point the SRU1060 at the TV and check that it responds as it should.
–If the TV responds to all of the key commands, the SRU1060 is ready
for use. Do not forget to note your code.
•If the device does not respond at all, or not to all of the key
commands, start again from step 2 and try the next code from
the list.
8ENGLISH
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 8

3. Keys and functions
The illustration on page 3 gives an overview of all keys and their functions.
TV keys
3 4 - VOL + . . . . . . . . . . . adjusts the TV volume.
2s. . . . . . . . . . . . . . . . . mutes the sound of the TV.
™A/V . . . . . . . . . . . . . . . switches between external inputs of your
equipment.
( ) - PROG + . . . . . . . . . selects a previous or following channel.
¡. . . . . . . . . . . . . . . . selects wide screen TV.
£TV. . . . . . . . . . . . . . . . switches TV on and off.
DVD keys
!DVD . . . . . . . . . . . . . . switches DVD on and off.
7DISC MENU. . . . . . opens disc menu.
5 & Cursor keys. . . . . . . cursor up, down in a menu.
6 * Cursor keys. . . . . . . cursor left, right in a menu.
8MENU . . . . . . . . . . . . turns the menu on and off.
95. . . . . . . . . . . . . . . . . - rewind
$2. . . . . . . . . . . . . . . . . - play
09. . . . . . . . . . . . . . . . . - stop
@;. . . . . . . . . . . . . . . . . . - pause
#6. . . . . . . . . . . . . . . . . - wind
%OK . . . . . . . . . . . . . . . confirms your selection.
^BACK. . . . . . . . . . . . . jumps back one level in the menu or turns
off the menu.
General
1LED
•If the device does not respond at all, or not to all of the key
commands, follow the instructions under ‘Setting the remote
control’. It is possible that you must enter another code for the
device.
9ENGLISH
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 9

4. Restoring the original functions of your
remote control
1Keep keys DISC MENU and BACK on
the SRU1060 pressed simultaneously for
three seconds,until the LED flashes twice
and then remains lit.
2Press the TV (or DVD) key.
All original functions have now been
restored and any extra functions have been
deleted.
5. Troubleshooting
• Problem
– Solution
• The LED blinks four times after every key press.
– The remote control is indicating that its battery is running low. Replace the old
battery with a CR2025 Lithium battery.
•The device you want to operate does not respond and the LED does
not flash when you press a key.
–Replace the old battery with a CR2025 Lithium battery.
•The device you want to operate does not respond but the LED does
flash when a key is pressed.
–Point the SRU1060 at the device and make sure that there are no
obstructions between the SRU1060 and the device.
•The SRU1060 does not respond properly to commands.
–Maybe you are using the wrong code.Try programming the SRU1060 again
using another code, which is mentioned under the brand of your device, or
reset for automatic search to find the right code. If the device still does not
respond, call our helpline.
10 ENGLISH
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 10

•You have difficulties operating all of the functions on your device.
– Maybe the SRU1060 has to be adapted to the model of the device.
Call our helpline for details.
•Your brand of device is not in the code list.
– Try to set the SRU1060 automatically. See ‘Automatically setting the
remote control’.
•None of the codes works during manual setting of the remote control.
– If that is the case, follow the instructions under ‘Automatically setting the
remote control’.
6. Need help?
If you have any questions about the SRU1060, you can always contact us.
You will find or contact details after the code list at the back of this manual.
Read this manual carefully before you make a call.You can solve most of the
problems yourself. If you cannot find any answers to your problems, write
down the details of your device shown in the code list at the back of this
manual.This will help our operators to assist you better and more quickly.
Look up the numbers of the models in the instructions accompanying the
device or on the back of your device.When you call our helpline, make
sure the device is to hand so that our operators can help you determine
whether your remote control is working properly.
The model number of your Philips universal remote control is SRU1060.
Date of purchase: ......../......../........
(day/month/year)
11
ENGLISH
SRU1060_A6.qxd6 25-08-2005 12:03 Pagina 11