Philips TD6411/BG051P User manual

PHONE BOOK
BABY SIT
AddEntry
RemoveEntry
Standby
1
5
RINGERS
2
Handset
BaseStation
*ANSW SETUP
Day&TimeSetting
RemoteControlCode
NumberofRings
MessageRecording
3
4
**SOS
SETUP
7
ChangeBaseStationName
RegisterHandset
RemoveHandset
AddHandset
RecallType
NetworkType
DialMode
AutomaticDiallingPause
R
BASE SEL
6
* Onis Memo only
** Onis only

The Onis handset
Earpiece
Down Key
Press this key to move through the
menu or to decrease earpiece
volume during calls.
OK Key
Press this key to confirm a menu
selection or to scroll the number on
the display
Phonebook Key
Press this key to consult your
Phonebook.
Number/Character
Keypad
Use these keys for dialling and for
entering characters.
Redial Key
Press this key to redial the last
number called.
Display
This display tells you what is
happening on your telephone
Up Key
Press this key to move through the
menu or to increase earpiece
volume during calls or to delete a
character when entering a number
or name.
Dialling Key
Use this key to make, answer
or end calls.
Recall/Menu Key
Press this key to consult the
menus, or to use the Recall
function during a call.
Internal Call Key
Press this key to make internal
calls and to transfer an outside call
to another handset.
SOS Key
Press this key to make an
emergency call.
Microphone
In the interest of improving its products and services, the manufacturer reserves the rights to modify the
specifications contained in this document at any time and without prior notice.
Copyright © Philips 1998 - All rights reserved

The Onis Memo handset
Microphone
Down Key
Press this key to move through the
menu or to decrease earpiece
volume during calls.
Memo Recorder Key
Press this key to operate your
memo recorder.
OK Key
Press this key to confirm a menu
selection or to scroll the number on
the display.
Phonebook Key
Press this key to consultyour
Phonebook.
Number/Character
Keypad
Use these keys for dialling and for
entering characters.
Redial Key
Press this key to redial the last
number called.
Internal Call Key
Press this key to make internal calls
and to transfer an outside call to
another handset.
Display
This display tells you what is
happening on your telephone.
Up Key
Press this key to move through
the menu or to increase earpiece
volume during calls or to delete a
character when entering a
number or name.
Loudspeaker Key
Press this key to turn the handset
loudspeaker on or off.
Dialling Key
Use this key to make, answer
or end calls.
Recall/Menu Key
Press this key to consult the
menus, or to use the Recall
function during a call.
Caller List Key
Press this key to consult the
caller list.
Earpiece

The display
When:
Onis Memo only:
Base station indicator light:
See page 28 for explanation.
This line of th
e
display shows
up to 10
numbers or
characters.
These symbols
tell you what is
happening on
your phone.
Mis on - you are consulting the menus.
Pis on - you are consulting the Phonebook.
tis on - a call is in progress.
blinks - the outside line is ringing.
bis on - the handset is charging when on the base station.
- the battery is discharged when off the base station.
Ais on - your handset is out of the range of the base station.
- your handset is not subscribed to any base station.
- the base station is not powered.
Eis on - there are messages on your memo recorder.
lis on - your memo recorder is switched on.
- you have pressed the rkey to operate your memo recorder.
blinks - your memo recorder is answering a call.
Uis on - there are new entries in the caller list since your last consultation.
his on - the handset loudspeaker is on.

Table of Contents2
Table of Contents
Safety information 4
Installing your Onis 5
Connecting your phone 5
Deciding where to put the base station 5
Connecting the base station 5
Connecting another telephone (UK only) 6
Ringer Equivalence Number or REN (UK only) 6
Charging your handset 6
Battery installation 6
Handset charge 7
Handset discharge 7
Testing your telephone 7
Using your Onis 8
Making a call 8
Answering a call 9
Redialling the last number called 9
Adjusting the handset earpiece volume 9
Using the handset loudspeaker (Onis Memo only) 9
The caller list (Onis Memo only) 10
Caller identification 10
Caller list functions 10
Consulting the caller list 11
Dialling from the caller list 11
Removing an entry from the caller list 11
Creating a Phonebook entry from the caller list 11
Accessing your memo recorder from the caller list 11
Your Onis Memo recorder (Onis Mémo) 12
Setting up your memo recorder 12
Recording an outgoing message 12
Setting the day and time 13
Using your memo recorder 14
Switching on the memo recorder 14
Switching off the memo recorder 14
Intercepting calls 14
Listening to received messages 15
Erasing messages 15
Personalising your memo recorder 15
Entering a remote control code 16
Changing the number of rings 16
Switching message record on or off 17

Table of Contents 3
Your memo recorder’s advanced functions 17
Recording a local message 17
Switching on the memo recorder by remote control 18
Calling into your memo recorder by remote control 18
Your Phone book and emergency number 19
The phone book 19
Storing a name and number in your phone book 19
Using the handset keypad to enter characters 19
Personalising your telephone 20
Entering menu mode 20
Setting the dial mode 20
Selecting the ringer melody and volume 21
Handset ringer 21
Base station ringer 21
Using the battery saver 21
Making a call using the phone book 22
Removing a name and number from your phone book 22
The emergency number (Onis) 22
Storing an emergency number - SOS 22
Calling the emergency number 23
Using advanced functions 24
Inserting automatic dialling pauses 24
Registering a new handset with your base station 24
Changing the name of your base station 25
Call waiting 25
Setting up Baby Sit 25
Registering one handset with several base stations 26
Selecting the base station 26
Removing a handset 26
Connection to a PABX 27
Selecting the network type 27
Setting the recall type 27
Useful tips and maintenance 28
Beeps and melodies 28
Base station indicator light 28
Telephone troubleshooting 29
Memo recorder troubleshooting (Onis Memo only) 29
Caring for your phone 30
Battery removal 30

4
Safety information
This equipment is not designed for making emergency
telephone calls when the power fails. Alternative
arrangements should be made for access to emergency
services.
This product may be used legally only in a country where the appropriate authority
has given its specific authorisation. This authorisation appears on a label under
the base station.
The marking on the product certifies its conformity to the technical regulations
for user safety and electromagnetic disturbance which were applicable on the date
of approval in accordance with European Union directive No. N°73/23/EEC,
89/336/EEC, 91/263/EEC and 93/68/EEC.
Power requirements
This product requires an electrical supply of 220-240 volts, alternating
monophased current, excluding IT installations defined in standard EN 60-950.
Warning!
The electrical network is classified as dangerous according to criteria in the
standard EN60-950.
The only way to power down this product is by unplugging the power cable from the
electrical outlet. Ensure the electrical outlet is located close to the apparatus and
is always easily accessible.
To be able to make calls in the event of a power cut, it is recommended that this
telephone be used as a complement to another telephone which does not require
mains power.
Telephone connection:
The voltage on the network is classified as TNV-3 (Telecommunication Network
Voltages, as defined in the standard EN 60-950)
Safety precautions:
•Do not allow the handset to come into contact with water.
•Do not open the handset or the base station. This could expose you to high
voltages. Contact our after-sales service for all repairs.
•Do not allow the charging contacts or the battery to come into contact with
conductive materials such as keys, paper clips, rings, bracelets, etc.
•Make sure you insert the batteries with their polarities in the correct position
(see page 6).
What you get with your phone
•1 cordless handset
•1 base station
•1 power cable
•1 telephone cable
•1 user manual
•2 standard AA/R6 rechargeable batteries

Installing your Onis 5
Installing your Onis
Connecting your phone
Deciding where to put the base station
•To reduce to a minimum any interference with other electronic devices such as
telephones, televisions, screens, etc. we advise you to place your base station at
least 50 cm from any such device.
•Place the base station on a flat surface such as a desk.
•Do not install the base station in a damp or humid room.
•Do not place the base station near a strong source of heat.
The operating range of your cordless telephone will vary according to your
environment. Significant obstacles such as concrete walls or metallic supports
(windows and door frames, partitions, etc.) will lessen the communication range
between the base station and the handset.
The range can be improved by placing the base station higher than the handset.
Connecting the base station
Make sure that you connect the power plug to the correct mains voltage of
220-240V.
2Step two
Plug the power cable
into the base station
and then into the wall
outlet.
Plug the telephone
cable into the base
station and then into
the telephone
connector on the wall.
1 Step one
2 1

Installing your Onis6
Connecting another telephone (UK only)
If you connect a second telephone (standard telephone) on the same line,
please use a T-Adaptor.
Ringer Equivalence Number or REN (UK only)
Your Onis has a Ringer Equivalence Number (REN) of 1.0 . To determine the
maximum number of telephones that can be connected to your line, add together
the individual RENs of all the apparatus you wish to connect. If this total exceeds
four, one or all of your telephones may not ring correctly.
Charging your handset
Your handset is powered by 2 rechargeable AA/R6 batteries. In case of
replacement, you must use the following approved batteries: PHILIPS R6 NC-P,
Saft RC6. Never use non rechargeable batteries! The manufacturer is not
liable if these recommendations are not respected.
Battery installation
Slide down and lift off the battery cover.
Insert the new batteries as shown.
Replace the battery cover.
To B.T. socket
T-Adaptor
Another telephone
Telephone line cord
1
2
3
1 2
3

Installing your Onis 7
Handset charge
Before you use your telephone for the first time, charge the handset for at
least 16 hours. This precaution helps to lengthen the life of the batteries.
To charge your handset, place it on the base station. The bsymbol will appear
on the display to indicate that the handset is charging.
When the bsymbol disappears, your handset is fully charged.
The base station must be connected to a power supply using the power cable
supplied with your phone.
Handset discharge
Shortly before the handset is totally discharged, the bsymbol appears on the
handset display. If you are in the middle of a call, you will also hear a warning beep.
The handset will switch itself off shortly afterwards. You will need to recharge the
handset before you can use it again.
Testing your telephone
Now that your telephone is installed, try making a call.
•Press ton the handset. The tsymbol appears on the display and you hear
the dial tone.
•Dial the number. The digits you dial appear on the display and the dial tone
should stop.
If you have problems making your test call, make sure that the telephone cord is
correctly plugged into the telephone network socket and into the base station
socket, that the base station is plugged into a power outlet, and that the base
station light is on.
If your base station is correctly connected but the dial tone does not stop when you
dial the number, you need to change the dial mode. To do this refer to “Setting the
dial mode” on page 20.
Tips
- To ensure an optimum handset charge, replace the handset on the
base station regularly.
- The keypad can face upwards or downwards. However, the ringing
tone is louder when the keypad faces downwards.

Using your Onis8
Using your Onis
Making a call
Direct dialling
Press the tkey on the handset.
The tsymbol is shown on the display and you hear the dial tone in the
handset earpiece.
Dial the number using the number keys.
The number called is displayed after the last key is pressed.
If the number you enter is longer than 10 digits, the display will scroll the
number to the left to show the last digits.
To hang up, press tor replace the handset on the base station.
The duration of your call in minutes and seconds is displayed for 4 seconds.
Dialling with number preparation
This way of dialling allows you to make corrections to the number before dialling.
Dial the number (up to 23 digits) before pressing the tkey. You can
use the +key to make corrections by cancelling the last digit
entered.
If the number you enter is longer than 10 digits, the display will scroll the
number to the left to show the last digits.
Press the tkey on the handset.
The number prepared is automatically dialled.
Onis Memo only: you can also press H. The handset loudspeaker is activated
and the number is dialled.
To hang up, press tor replace the handset on the base station.
The call duration is displayed for 4 seconds.
1
2
3
1
Tip
If you want to see the whole number you have dialled so far, press
o. The number will scroll to the left if it is longer than 10 digits.
2
3

Using your Onis 9
Answering a call
When someone calls you, the base station and the handset ring, the tsymbol
blinks on the handset display and the green light on the base station flashes.
Press the tkey on the handset.
The tsymbol stops blinking on the handset. The green light on the base
station blinks regularly to indicate that a call is in progress.
Onis Memo only: you can also press H. The handset loudspeaker is
activated and you can take the call.
To hang up, press tor replace the handset on the base station.
The call duration is displayed for 4 seconds.
Redialling the last number called
Direct redial
Press the tkey on the handset. Wait for the dial tone.
Press the Bkey on the handset.
The last number called is shown on the display and dialled automatically.
Redial with number correction
Press the Bkey on the handset.
The last number called is shown on the display. You can use the +key to
correct the number.
Press the tkey on the handset.
Adjusting the handset earpiece volume
You can adjust the earpiece sound volume during a call by pressing +or -.
You can choose from 3 possible sound levels. The sound level you have selected
will be set for future calls.
Using the handset loudspeaker (Onis Memo only)
Your handset is fitted with a loudspeaker so that other people with you can listen to
the conversation.
During a call, press H.
The sound is amplified through the loudspeaker at the back of the handset.
Adjust the volume of the loudspeaker when it is on, using +or -.
To turn off the loudspeaker, press Hagain.
1
2
1
2
1
2
1
2
3

The caller list (Onis Memo only)10
The caller list (Onis Memo only)
Caller identification
Your Onis Memo is equipped to receive the telephone number of your callers from
the telephone network. In order to use the functions associated with caller
identification you must subscribe to the caller identification service provided by
your telephone operating company.
When your telephone rings, your handset(s) will display your caller’s number if it is
available from the telephone network. If your caller’s number is stored in the
handset Phonebook with an associated name, this name will be displayed instead
of the number.
Caller list functions
Your Onis can store the identification of up to 20 calls unanswered by the
handset(s). Each entry in the caller list contains:
•the caller’s telephone number (up to 23 digits) or the caller’s name (up to 20
characters) if this is stored in your Phonbook or supplied by the Network
•the day and time of the call
•the number of calls by the caller (up to 9 calls)
If a call is answered by you, the caller’s number will not be stored in the caller list.
If the same number calls several times, only the last call is kept in the list.
The U symbol is displayed on the handset when there are new entries
in the caller list.
When the caller list is full the oldest entry is removed, even if you have not read it.
The caller list is not deleted if the base station is switched off.
You can consult the caller list, then call back your correspondents directly from the
list or remove the numbers. You can also create a Phonebook entry directly from
the caller list.

The caller list (Onis Memo only) 11
Consulting the caller list
You can only consult the caller list when the handset displays the base station
name and the handset number (Standby mode).
Press Uto enter the caller list, then +or -to scroll through the list.
Press oto toggle between the caller number (or name), day and time
of call, number of calls, and the option REMOVE? (pressing oafter
REMOVE? will delete the entry).
Press Uto exit the caller list.
Note:
The entry is considered unread until the “number of calls” is displayed.
Dialling from the caller list
While consulting an entry in the caller list, you can dial the number directly.
Press tor Hto return the call of the caller currently displayed in the
list.
The number is dialled automatically.
Removing an entry from the caller list
While consulting an entry in the caller list, you can choose to delete it.
Press ountil REMOVE? is displayed. Press oagain.
The entry is removed and the next entry is displayed.
Creating a Phonebook entry from the caller list
While consulting an entry in the caller list, you can automatically create the entry in
the Phonebook, provided that the Phonebook is not full.
Press P , enter a name (limited to 10 characters), then press o.
The entry is created even if the number already exists in the Phonebook, or
the name is supplied by the network.
Note that you can cancel the copy operation by pressing Pinstead of o.
Accessing your memo recorder from the caller list
If the E icon is displayed while consulting an entry in the caller list, it indicates
that a message is associated with the entry. This message can be played by
pressing the rkey.
1
2
3
1
1
1

Your Onis Memo recorder (Onis Mémo)12
Your Onis Memo recorder
(Onis Mémo)
Your memo recorder offers the following functions:
•answering machine only facility with no recording of incoming messages (callers
will hear your outgoing message, but will be unable to leave messages).
•answering machine and recording facility (callers will be able to leave messages
after hearing your outgoing message). You can receive up to 32 messages
within a total capacity of 6 minutes.
If you have received new messages:
•the base station indicator light flashes red 3 times every 2 seconds.
If your memo recorder is handling a call:
•the green indicator light on the base station blinks.
•the tand lsymbols are shown on the handset display, along with the number
of messages and the time.
Setting up your memo recorder
Recording an outgoing message
If you want to record or change an outgoing message, proceed as follows:
Press rto enter memo recorder mode then, if message playback
starts, press s.
lis displayed.
Press K, then v.
RECORD is displayed.
Speak clearly close to the microphone of the handset.
You have up to 30 seconds to talk.
Once your message is finished, press sto stop recording.
A beep indicates the end of the recording.
To hear your outgoing message, press v.
Tip
All the symbols appearing in grey on the keypad refer to the
memo recorder ( Vplayback, sstop, Krecord, etc.).
1
2
3
4

Your Onis Memo recorder (Onis Mémo) 13
Press rto exit memo recorder mode.
Note:
To change your outgoing message, simply record over the previous one by
proceeding as described above.
Checking your outgoing message
Press v.
The memo recorder starts playing back the message. The memo recorder
stops automatically at the end of playback (you will hear 1 beep).
Press rto exit memo recorder mode.
Setting the day and time
You need to enter the day and time so that your memo recorder can time stamp the
messages you receive. When you enter memo recorder mode or when you listen
to your messages, the day and time are displayed.
In the event of a power failure, this operation must be repeated.
Default setting: MON 00:00.
Press R, press -until you reach ANSW SETUP
, then press o.
Press -or +until you reach DAY TIME, then press o.
Press -or +to select a day of the week, then press oto confirm.
Press -or +to select the hour, then press oto confirm.
Press -or +to select the minutes, then press oto confirm.
Press Rto exit menu mode.
Note:
When you switch the unit on again after a power failure, the default day and time
are: MON 00:00. After a power failure, the red light on the base station flashes
quickly to indicate that the time setting has been erased.
5
1
2
1
2
3
4
5
6

Your Onis Memo recorder (Onis Mémo)14
Using your memo recorder
When you have installed your Onis and set up the memo recorder (day and time
set), the memo recorder is ready for use.
Switching on the memo recorder
Press rto enter memo recorder mode then, if message playback
starts, press s.
lis displayed. The number of messages and the time are displayed.
Press ON .
ANSW ON is displayed. Your memo recorder is now on.
Press rto leave memo recorder mode.
lremains displayed to indicate that the memo recorder is on.
You will hear an error beep in the following cases:
•No outgoing message has been recorded. NO OUT MES is displayed.
•The memory is full. ANSW FULL is displayed.
Switching off the memo recorder
Press rthen press OFF .
ANSW OFF is displayed. The memo recorder is switched off.
Press rto leave memo recorder mode.
Intercepting calls
Using your handset
If your memo recorder has started handling a call and you wish to take it:
Press tto take the call.
The memo recorder will stop handling the call. You can talk to the caller.
Using another telephone
If you have another telephone (e.g. a corded telephone) connected in parallel and
you want to intercept the call that your memo recorder is handling:
Pick up the receiver and press Dtwice on the other telephone.
The memo recorder will stop handling the call. You can talk to the caller.
1
2
3
1
2
1
1

Your Onis Memo recorder (Onis Mémo) 15
Listening to received messages
The Esymbol on the handset screen indicates that new messages have been
received.
Press rto enter memo recorder mode.
The day, time and number of messages received are displayed.
The memo recorder plays back the messages automatically.
To handle your messages during playback, use the following keys:
Press <to play the current message again.
Press <twice to hear the previous message again.
Press >to listen to the next message.
Press sto stop message playback.
Press rto exit memo recorder mode.
Erasing messages
Erasing individual messages
Press the rkey on the handset.
The display shows the day, time and the number of messages received.
The memo recorder plays back the messages automatically.
While listening to the messages, press xwhen the memo recorder
plays back the message you want to erase.
A beep confirms that the message has been erased. The number of the
received messages displayed is updated automatically.
Erasing all the messages received
Press r, then s. Press and hold xfor 2 seconds.
A beep confirms that all the messages have been erased.
Personalising your memo recorder
If you have recorded an outgoing message and set the day and time, your memo
recorder is ready for use. However, you can also personalise the settings on your
memo recorder.
The following settings are available:
•Define a remote control code (RCC: ----)
See “Entering a remote control code” on page 16.
•Choose the number of times the telephone rings before your memo recorder
picks up (Number of rings). See “Changing the number of rings” on page 16.
•Decide whether your callers can leave a message (RECORD ON/OFF).
See “Switching message record on or off” on page 17.
1
2
3
4
1
2
1

Your Onis Memo recorder (Onis Mémo)16
Entering a remote control code
You need to enter a code in order to be able to use your memo recorder’s remote
control functions from another telephone e.g. to listen to your messages from a
telephone outside your home.
Press R, then press -until you reach ANSW SETUP
. Press o.
Press -until you reach RCC:, then press o.
Enter your 4 digit code (e.g. 1234), then press o.
The handset beeps to confirm the code.
Press Rto exit menu mode.
Note:
You can correct an error when you are entering your remote control code (RCC)
by using the +key.
If you wish to change your remote control code, repeat the above procedure.
If you to wish to erase the remote control code during step of the procedure
described above, press +four times, then press o, and finally press R.
Changing the number of rings
You can change the number of times your telephone rings before your memo
recorder answers a call.
Press R, then press -until you reach ANSW SETUP
. Press o.
Press -until you reach RINGS, then press o..
Press -or +to select 2 RINGS, 3 RINGS, 4 RINGS, 5 RINGS, or TOLL
SAVER, then press oto confirm your choice.
Press Rto exit menu mode.
The Save function TOLL SAVER
This is used when you call into your memo recorder by remote control (see “Calling
into your memo recorder by remote control” on page 18).
When TOLL SAVER is selected, you can tell if a new message has been received
since you last rang in.
1
2
3
4
3
1
2
3
4