Philips ThinkLink SE8881B/38 User manual

Quick start guide
SE888

Note
*In multi-handset packs, there
are additional handsets,
chargers and power adapters.
** In some countries, you have
to connect the line adapter to
the line cord, then plug the line
cord to the telephone socket.
Caution
• Use only the supplied batteries
and power adapter.
What’s in the box
Handset*
Base station
Charger*Power adapter*Line cord**
CD rom
Quick start guide
Guarantee

Connect the base station and charger
Telephone
socket
Power
socket
Power
adapter
Power
socket
Extra handset
charger
Telephone
base station
1 Connect each end of the power adapter to:
• the DC input jack at the bottom of the base station;
• the power socket on the wall.
2 Connect each end of the line cord to:
• the telephone socket at the bottom of the base station;
• the telephone socket on the wall.
3 For multi-handset version, connect each end of the power
adapter to:
• the DC input jack at the bottom of the extra handset charger.
• the power socket on the wall.
NoteChargethebatteriesfor8hoursbeforerstuse.
1Get started

Congure your phone
1 The batteries are pre-installed in the handset. Pull the battery
tape off from the battery door before charging.
2 Whenusingyourphoneforthersttime,youseeawelcome
message (country dependent).
3 Select your country, then press [OK] toconrm.
4 Set the date and time.
• If the time is in 12-hour format, press *key to select [AM] or
[PM] .

Charge your phone
Charge
8 hours
Place the handset on the base station to charge the handset.
When the handset is placed correctly on the base station, you hear
a docking sound.
»The handset starts charging.
NoteChargethebatteriesfor8hoursbeforerstuse.
Check the battery level
When the handset is off the base station/charger, the bars
indicate the battery level (full, medium and low).
When the handset is on the base station/charger, the bars
ashuntilchargingcompletes.
Theemptybatteryiconashesandyouhearanalerttone.
The battery is low and needs recharging.

Charge your mobile phone
Telephone
base station
1 For iPhone users, connect the plug of your USB charging cable
(not supplied) to the USB socket at the bottom of SE888.
2 For mobile phones with micro USB charging, connect the micro
USB cable plug to the micro USB socket of the mobile phone.

2Bluetooth
Pair SE888 with your mobile phones
Make sure the Bluetooth function of the mobile phones
is activated and in searching status.Then you can do the
pairing in this way:
1 On the base station, press MENU.
2 Select [Bluetooth] > [Find Me] .
3 Place the mobile phone close to the base station, then
press [OK] toconrm.
4 On the mobile phone, select SE888 and connect.
5 Enter the PIN code (0000) on the mobile phone if
necessary.
»When SE888 and the mobile phone are paired,
or is displayed on the screen of the handset
and base station.
Note
• When the Bluetooth device list is full, remove some
mobile phone names before pairing can start.
• If the name of SE888 exists in your mobile phone, you
have to remove it from your mobile phone.Then you
can do the pairing again.
Tip
For PC pairing and PC phonebook download, install
the PC software ‘ThinkLink’ saved in the cd rom or at
http://www.philips.com/support

Call
Quick call from land line
Press / on the handset or on the base station
and dial the phone number.
Dial before you call
1 Dial the phone number on the handset or base station.
2 Press / to select the land line or Bluetooth line ( /
/ ) from which you want to make an outgoing call.
3 Then, you can either:
• press / on the handset; or
• press or on the base station and select a line
or mobile phone to dial out the call.
Note Make sure that the Line settings are set to
[Home] for land line or [Mobile 1]/[Mobile 2] for
Bluetooth line. For information, see Line settings in the
Phone settings chapter in the user manual.
Tip If you select [Auto] on the handset, the idle line is
pre-selected for an outgoing call, with [Home] as the
highest priority. Then [Mobile 1] and [Mobile 2] . If
you select [Manual] , select an icon among these three
options.
3Enjoy

Answer a call
• When there is an incoming call from the land line, press
/ on the handset or on the base station.
• When there is an incoming call from the Bluetooth
line, press / on the handset or on the base
station.
• When there are incoming calls from the land line and
Bluetooth line at the same time, press / on the
handset/base station to select a call, then,
• on the handset, press / ; or
• on the base station, press or to pick up one
of the calls.
End a call
• Press on the handset or on the base station.
• Place the handset to the base station.
Adjust the volume during a call
Press / on the handset or / on the base station to
change the volume during a call.
Add a contact in the phonebook
1 Press on the handset or base station.
2 Select [Option] > [Add new] , then press [OK] to
conrm.
3 Enter the name then press [OK] toconrm.
4 Enter the number, then press [Save] toconrm.

Record an announcement
1 Press [Menu]
2 Select > [Announcement] , then press [OK] to
conrm.
3 Select [Answer & rec.] or [Answer only] , then press
[OK] toconrm.
4 Select [Record new] , then press [OK] toconrm.
5 Start recording close to the microphone after the beep.
6 Press [OK] to stop recording.
»You can listen to the newly recorded
announcement on the handset.