Philips SQM5322/27 User manual

1
Register your product and get support at
www.philips.com/welcome
SQM5322/27
EN Tilting wall mount 3
FR 
Support mural inclinable 9
ES Soporte de pared basculante 16

2
Table of contents
1 Important 3
2 Your tilting wall mount 3
2.1 What’s in the box 4
2.2 What you’ll also need 4
3 Installing your wall mount 5
3.1 Mounting the wall plate (drywall) 5
3.2 Mounting the wall plate (concrete) 5
3.3 Attaching the arms to the display 6
4 Mounting and adjusting 7
5 Guarantee and service 8

3
1 Important
Take time to read this manual before you
use your wall mount. It contains important
information and notes regarding operating your
wall mount.
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved. Reproduction in whole or in
part is prohibited without the written consent of
the copyright owner.Trademarks are the
property of Koninklijke Philips Electronics N.V.
or their respective owners.
BWarnings
• Make sure these instructions are read
and thoroughly understood before
attempting installation. If you are
unsure of any part of this installation,
contact a professional installer for
assistance or contact Customer Service
at 1-919- 573-7854.
• This product has been designed
for application on a vertical wall in
commercial and residential buildings,
constructed of wood wall studs or
masonary (solid concrete, brick, and
stone). If you are unsure of your wall
composition or for assistance with other
surfaces, contact a qualified installer.
• This product is not designed for use on
walls constructed of metal studs. If you
are unsure of your wall composition
or for assistance with other surfaces,
contact a qualified installer.
• The wall or mounting surface must be
capable of supporting the combined
weight of the mount and the display;
otherwise the structure must be
reinforced.
• Do not exceed the maximum load
capacity of 165lbs for this product.
• Safety gear and proper tools must
be used. Failure to do so can result in
property damage and/or serious injury.
• A minimum of two people are required
for this installation. Do not attempt
to install this mount alone under any
circumstance.
• Follow all instructions and
recommendations regarding adequate
ventilation and suitable locations for
mounting your display. Consult the
owner’s manual for your display for
more information.
• This mount is equipped with a safety
device that must be used whenever
the mount holds a display. Not using
the safety device can cause property
damage, serious injury, or death.
2 Your tilting wall mount
Congratulations on your purchase and welcome
to Philips!
To fully benefit from the support that Philips
offers, register your product at
www.philips.com/welcome.
Designed to fit most TV brands with a focus
on safety and ease of use. Includes Easy 1-2-3
installation kit, complete with: all necessary
hardware for mounting on different types of
walls, mounting templates, stud finder and
bubble level. C-UL US listed for weight capacity
up to 165lbs.

4
2.1 What’s in the box.
Wall mount Stud finder Cotter pin Bubble level
Bag #1 (A) M4x12 Bolt (x4) (B) M4x30 Bolt (x4) (C) M4 Lock Washer (x4)
Bag #2 (D) M5x12 Bolt (x4) (E) M5x30 Bolt (x4) (F) M5 Lock Washer (x4)
Bag #3 (G) M6x12 Bolt (x4) (H) M6x35 Bolt (x4) (I) M6 Lock Washer (x4)
Bag #4 (J) M8x16 Bolt (x4) (K) M8x40 Bolt (x4) (L) M8 Lock Washer (x4)
Bag #5 (M) Small Spacer (x4) (N) Large Spacer (x4) (O) M6 Washer (x4)
Bag #6 (P) Concrete Anchor (x6) (Q) M8x63 Lag Bolt (x6) (R) Lag Bolt Washer (x6)
2.2 What you’ll also need.
• Phillips head screwdriver
• Ratchet or driver with 1/2” (13 mm) socket
• Portable or electric drill
• 1/4” (6 mm) drill bit and stud finder for drywall installation
• 3/8” (10 mm) masonry bit for concrete installation

5
3 Installing your wall mount
In this chapter, the basic steps to get you started
are described.
B Warning
Carefully read the safety precautions
in “Section 1 Important” before you
install the wall mount.
3.1 Mounting the wall plate (drywall)
B Warning
For safety reasons, this mount must
be secured to three adjacent wood
studs at least 16” apart.The studs
must be capable of supporting the
combined weight of the mount and
display.
1See enclosed mounting template for
diagram and guide of how to mount
properly on the wall.
2Using a stud finder, locate and mark three
adjacent studs for securing the mount
(make sure your marks are in the center
of each stud). You can use your own stud
finder or the one included in the hardware
kit.
D Note
Once studs have been located you will
need to verify with a hammer and a
nail
A) Simply place the nail over your
mark on the wall and tap in with
hammer. If the nail encounters
resistance and is secure in wall you
have veried a stud location
B) If it just pushes through with no
resistance you will need to start
over and locate the stud.
3Using the enclosed mounting template,
place the diagram against the wall and mark
six locations (two per stud) on the wall
where the mount Is to be Installed. Be sure
to use the center of each stud.
4With the help of another person, place the
mount against the wall and level it using the
bubble guide.
5While another person holds the mount in
place, mark six locations (two per stud) on
the wall where the mount is to be installed.
Be sure to use the center of each stud.
(these marks should line up with the ones
made in step 3 above using the template).
6Set the mount aside and drill a 1/4” (6 mm)
pilot hole at each marked location.
7Place the mount back against the wall and
secure it using the lag bolts (Q) and lag bolt
washers (R) provided. Do not over-tighten
these bolts and do not release the mount
until all bolts are in place.
8Once all (6) lag bolts are in place you must
tighten each one. Be sure not to over
tighten. 1
1
3.2 Mounting the wall plate (concrete)
B Warning
For safety reasons, the concrete wall
must be capable of supporting the
combined weight of the mount and
display.
1See enclosed mounting template for
diagram and guide of how to mount
properly on the wall.
2Using the enclosed mounting template,
place the diagram against the wall and mark
six locations on the wall where the mount
Is to be Installed.
3With the help of another person, place the
mount against the wall and level it using the
bubble guide.
4While another person holds the mount in
place, mark six locations on the wall where