Philips AquaTrio Cordless 7000 Series User manual

English 6
Bahasa Melayu 30
ภาษาไทย 54
简体中文 78
繁體中文 103
한국어 124
ﺔﻴﺑﺮﻌﻟﺍ 146

English
6English
Contents
Introduction _______________________________________________________________________________ 6
General description_________________________________________________________________________ 6
Before first use _____________________________________________________________________________ 6
Charging __________________________________________________________________________________ 8
Vacuuming and mopping hard floors _________________________________________________________ 9
Display icons and their meaning______________________________________________________________ 21
Replacement ______________________________________________________________________________ 23
Troubleshooting ___________________________________________________________________________ 24
Introduction
Thanks for buying this Philips product! To fully benefit from the support that
Philips offers, register your product at www.philips.com/MyAquaTrio7000s
General description
1 On/off button
2 + and - buttons
3 AUTOCLEAN button
4 Charging socket including sealing cap
5 Clean water tank
6 Dirty water tank
7 AquaSpin nozzle
8 Microfiber brushes
9 Handle
10 Cleaning brush
11 Adapter
12 Power plug
13 Philips Floor Cleaner XV1792
14 After-Clean & Storage station
15 Appliance holder
16 After-Clean tray
17 Baseplate
Before first use
Assembling the After-Clean & Storage station
In order to use the AUTOCLEAN function or store and charge the appliance on
the After-Clean & Storage station, you need to first assemble the station by
clicking the appliance holder into the baseplate.

7
English
Note: Make sure that the After-Clean tray is placed in the baseplate and that
the temperature in the room where the appliance is stored, charged and cleaned
is between 5 °C and 35 °C.
Note: you can store the cleaning brush in the After-Clean tray as well.
1To assemble the appliance, insert the handle into the main body ('click').
2To store the appliance, you can place it in the After-Clean & Storage station.
Slide the appliance on to the appliance holder so that the end of the
appliance holder sticks into the appliance.
If you need to disassemble the appliance again, follow the steps below:
1Insert a pin/flat screwdriver into the hole in the back of the appliance and
pull up the handle.
2Pull the handle out of the appliance while continuing to push the screwdriver
into the hole.

8English
Charging
The appliance is equipped with a 25 V Li-Ion battery. Charging takes 4 hours.
1To charge the appliance, open the sealing cap on the back of the appliance.
2Insert the power plug into the socket on the back of the appliance. Then
insert the adapter into the wall socket.
3A value between 0% and 90% flashes on the screen to indicate that the
appliance is charging.
4When the appliance is fully charged, the value 100% lights up on the screen.
After a few minutes, the display will switch off.
5Remove the power plug from the socket on the back of the appliance.
6Close the sealing cap.
Warning: Store and charge the appliance at a temperature
above 5°C and below 35°C.

9
English
Tip: You can charge the appliance in the After-Clean & Storage station.
Tip: You can charge the appliance separately in a place that suits you best.
Vacuuming and mopping hard floors
Using the appliance
The clean water tank and the dirty water tank are already attached to the
appliance upon delivery. You can use the appliance to clean hard floors.
Note: This appliance is suitable for vacuuming and mopping at the same time.
It is not necessary to vacuum the floor before mopping.
The appliance is suitable for vacuuming and mopping all types of hard floors,
except uncoated wooden floors. You can test the appliance on a small area out
of direct view, to make sure that the appliance is suitable for your floor.
1Push the button down to unlock the clean water tank and remove the clean
water tank.
2Open the cap on the clean water tank.

10 English
3Add 15 ml of the XV1792 Philips Floor Cleaner to the clean water tank.
Caution: Philips has only tested this appliance with XV1792 Philips
Floor Cleaner. Other detergents may lead to excessive foaming, which
reduces performance and may cause the appliance to malfunction.
XV1792 Philips Floor Cleaner is available in selected markets. When
using any other suitable liquid floor cleaner, add a maximum of 15 ml to
the clean water tank.
4Fill the clean water tank up to the top with cold or lukewarm tap water.
Caution: The tap water that is poured into the clean water tank must
not be warmer than 50°C.
5Close the water tank with the sealing cap.
6Place the clean water tank back into the appliance.