Philips HR 8358 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Impact Vacuum cleaner
HR 8358
PRODUCT INFORMATION
- Maximum air displacement : 30 l/sec
- Maximum vacuum water column : 300 cm
- Power consumptio (IEC) 225V : 1100 W
- Dust storage capacity : 2 litres
- Cord length (depends on version) : 5.3 m
- Filter system : 5 filters
- Dimensions cleaner : 37 x 28 x 23 cm
- Weight accessoiries : 4.8 kg
- Noise : 80 dB
- Colour : Yellow / Dark purple
- Electronic controled motor rpm
- Cordwinder build-in with flat cord
- Dustbag-full indicator in dustcover
OPTIONAL
Exhaust air filter HR 6932 (8836 932 01210)
Sydney cotton dustbag HR 6997 (8836 997 01010)
Sydney 3M dustbag HR 6999 (8836 999 90010)
Sydney paper dustbags HR 6999 (8836 999 01010)
4322 277 00264
02/03
SERVICE INFORMATION
- To open the appliance, first remove the screws A,B,C,D.
- To reach the motor remove the screws E.
- To disassemble the cordwider use Torx screw driver no T10,
which is one of set consisting of T20, T15, T10, T9, T8, T7 and
T6 = 4822 395 50145.
- Give attention that the contact fingers (item 45) are placed on the
cord-winder shaft in such a way that the pressure point of the
cordwinder knob to the cord winderlever (item 40) is vertical.
- The spare parts have been standardized as much as possible.
- Component configuration on exploded view may differ in case
of specific versions, however, the actual components are distin-
guished by means of code numbers.
- Item 1 Cotton dustbag is used in those countries where paper
dustbags are not available
- Item 41 Cord-winder spring unit is provided with a long spring,
both long and short cords can be used in combination with this
spring.
- Cordwinder spring has to be tensioned till maximum minus
approx. 1,5 revolution.
This product meets the requirements regard-
ing interference suppression on radio and TV.
After the product has been repaired, it should
function properly and has to meet the safety
requirements as officially laid down at this
moment.

Pos. 12 nc description
1 8836 997 01010 Sydney cotton dustbag (opt.)
8836 999 90010 Sydney 3M dustbags (opt.)
8836 999 01010 Sydney paper dustbags
2 4322 009 07510 dustbag holder
3 4322 009 07530 upperhousing (el.)
4 4322 001 73150 inletrubber
5 4322 003 16240 nose piece
6 4322 001 99290 wheel (24)
7 4322 002 22260 spindle
8 4322 009 07470 lower housing
9 4322 003 16310 handle el. (yellow)
10 4322 009 07600 vario knob (purple)
11 4322 009 07580 dust cover (yellow)
12 4322 001 72900 motor buffer
13 4322 001 73160 sealing m.c.
14 4322 000 35360 duo filter
14A 4322 009 08460 duo filter and holder
15 4322 003 16330 hinge
16 4322 009 07550 cord outlet
17 4322 003 16280 backgrille
18 8836 932 01210 exhaust filter
19 4322 009 07480 rear wheel
20 4322 003 16210 knobs (yellow)
21 4322 000 09750 pedal spring
22 4322 006 20080 Low Volt PCB
4322 006 22210 High Volt PCB
22A 4322 006 21480 switch (soldered version)
23 4322 001 73230 cooling connection
24 4322 003 16150 motor cap
25 4322 001 72780 buffer ring front
26 4322 006 97400 motor 110 V - 60 Hz / ans
4322 009 06430 motor 220 - 240 V / ans
Pos. 12 nc description
27 4322 003 11990 receptical housing
28 4322 009 07520 motor foam/disc/ans
40 4322 003 06620 push rod
41 4322 009 07610 reelhalf springside
42 4322 001 72360 brake tyre
43 4322 009 07640 base plate
44 4322 009 07620 reelhalf contactside
45 4322 009 07630 contact plate
46 4322 006 01880 Argentina L = 6.3 m
4322 006 01380 Australia L = 6.3 m
47 4322 006 01770 Japan / Taiwan L = 5.3 m
48 4322 006 01370 H.K. / U.K. L = 6.3 m
49 4322 006 01400 Euro 4.8 mm L = 6.3 m
50 4322 006 01480 Swiss L = 6.3 m
51 4322 006 01430 Italy L = 6.3 m
54 4322 004 21160 small nozzle (opt.)
55 4322 003 10070 tube clip
56 4341 004 22610 steel tube painted con. 55 cm.
57 4322 004 21850 bend + hose
58 4322 005 03770 bend handle
59 4341 004 20130 combi crevice brush
60 4322 004 21180 nozzle D272
61 4822 479 20039 nozzle brush
62 4822 479 20038 nozzle strip
4222 000 46640 DFU W. Europe
4222 000 46630 DFU E. Europe
4222 000 46650 DFU rest of world
M
SPEED
CONTROL UNIT
CORD WINDER
C

C
CD
10
3
6
40
2
1
5
4
45
46÷51
42
11
8
41
43
44
9
7

DAP1057
A
B
B
E
E
C
D
21
22
1
0
15
18
12
24
25
26
20
16
1
1
19
9
17
2827
13
14A
14
23
22A

DAP1058
60
61
62
57
58
56
55
59
46AUSTRALIA
JAPAN 47
EUROPE Ø 4.8mm 49
CH 50
ITALY 51
48GB
54