Philips Mobilo HR 8501 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Mobilo Vacuum cleaner
HR 8501
PRODUCT INFORMATION
- Maximum air displacement : 32 I/sec
- Maximum vacuum water column : 240 cm
- Power consumption (IEC) : 1200 W
- Dust storage capacity : 3 l
- Cord length (depends on version) : 6 metre
- Filter system : Paper dustbag
: Motor inlet filter
: Exhaust air filter
- Dimensions cleaner : 44.5 x 29.5 x 25 cm
- Weight cleaner : 5.5 kg
OPTIONAL
- Exhaust air filter HR 6932 = 8836 932 01210
- Hard floor nozzle HR 6943 = 8836 943 03010
- Active carbon filter HR 6949 = 8836 949 01010
- Active carbon filter replacem. set HR 6968 = item 12 + 13
- S-class filter HR 6992 = 8836 992 01010
- S-class filter replacement set HR 6994 = item 19 + 20
- Sydney cotton dustbag HR 6997 = 4322 004 93250
- Sydney closable pap. dustbag HR 6999 = 8836 999 01010
- Turbo brush HR 6988 = 8836 988 01010
- Sydney 3M-dustbag HR 6999 = 8836 999 90010
SERVICE INFORMATION
- To open the appliance, first remove the 2 screws of the control
panel (item 11) then with a big screw driver disconnect the 2
snap locks of panel and lower housing (see drawing).
4322 277 00203
00/02
PCS 101 336
- Component configuration on exploded view may differ in case
of specific versions. However, the actual components are distin-
guished bij means of code numbers.
- If a repair has been made, make sure that all functions of the
appliance are working correctly.
- The spare parts have been standardized as much as possible.
- Item 6, cotton dustbag, is used in those countries where paper
dustbags are not available.
- Item 21 is provided with a long cord-winder spring; both long and
short cords can be used in combination with this spring.
- Cordwinder spring has to be tensioned till maximum minus appox.
1,5 revolution.
- Depending on the original length of the cord, the spare cord must
be shortened.
- Item 71 up to and including item 85. The assembly of accessories
depends on the national version.
To connect the nozzle, the telescopic
tube and the handle: insert the
narrowed section into the wider section
while turning it a little.
To disconnect: pull while rotating.
To adjust the telescopic tube (item 74)
to the required length, use the knob in
the direction of the arrow while sliding
the top section of the telescopic tube
into or out of the lower section.
fig. 1
- To (dis)assemble the appliance use TORX screw driver no T15
= 4822 395 10329, which is one of a set consisting of T20, T15,
TI0, T9, T8, T7 and T6 = 4822 395 50145.
!Service
Information

1 4322 003 16520 Acc. cover
2 4322 000 67680 Spring
3 4322 009 06750 Dust cover
4 4322 001 94690 Packing ring
5 4322 003 12650 Front cover
6 8836 999 01010 Sydney closable pap. dustbag
8836 999 90010 Sydney 3M-dustbag
4322 004 93250 Sydney cotton dustbag
7 4322 009 06760 Dustbag carrier
8 4322 003 12280 Clamp of dustbag carrier
9 4322 003 12020 Dust compartment sealing
10 4322 003 16290 Badge
11 4322 003 12620 Back panel
12 4322 009 07040 Inlett grille + trio filter
13 4322 000 37300 Safety trio filter
14 4322 003 12660 Switch knobs
15 4322 001 72780 Buffering motor
16 4322 003 12080 Motor disc
17 4322 003 12510 Cord outlet
18 4322 009 06700 Lower housing + wheels
19 8836 932 01210 Exhaust air filter
20 4322 009 06910 Air outlet grille
21 4322 009 05350 Reel half spring unit
23 4322 001 72360 Brake tyre
24 4322 009 04800 Reel half contact unit
25 4322 009 05060 Contact ring plate
26 4322 007 11960 Cord set Australia L = 6.3 m
27 4322 007 12150 Cord set Japan/low voltage
28 4322 007 12190 Cord set UK L = 6.3 m
29 4322 007 11920 Cord set 4.8 mm pins L = 8.5 m
29 4322 007 11930 Cord set 4.8 mm pins L = 6.3 m
30 4322 006 01280 Cord set Swiss L = 8.5 m
30 4322 007 12020 Cord set Swiss L = 6.3 m
31 4322 007 11950 Cord set Italy L = 6.3 m
32 4322 003 12240 Dustbag sealing
33 4322 005 07270 Caster
34 4322 003 12560 Cover (opt.)
35 4322 009 06710 Rear wheel
37 4322 003 12030 Cord winder lever
41 4322 006 50580 Push button switch
42 4322 003 12010 Motor cover
43 4322 001 72790 Rear motor buffer
44 4322 003 09720 Suspension bracket
47 4322 009 06430 Motor 220-240V/50-60Hz
48 4322 000 09750 Spring switch-knob
71 4322 009 05400 Clip metal tube
72 4322 002 22610 Metal tube
73 4322 009 05410 Clip telesc. tube (opt.)
74 4322 004 21050 Telescopic tube (opt.)
75 4322 004 21850 Bend + hose ass’y
76 4322 005 03770 Bend ass’y
77 4322 003 12070 Crevice nozzle
78 4322 004 21160 Small nozzle
79 4322 004 22110 Big nozzle
DFU 4222 000 45280
This product meets the requirements regard-
ing interference suppression on radio and TV.
After the product has been repaired, it should
function properly and has to meet the safety
requirements as officially laid down at this
moment.
M
MAIN
SWITCH
CORD WINDER
C

3
4
8
6
33
3221÷31
12 13
9
7
5
CLICK
2
1

PCS 101 337
3534
19 20
17
12 13
48
10
16
15
43
47
44
42
41
37
11
14
CLICK
DAP1079
18

DAP1076
71 73
72 74
76
75
77
78
79

6
25
B
24
B
21
26AUSTRALIA
JAPAN 27
EUROPE Ø 4.8mm 29
CH 30
ITALY 31
DAP0778
23
28B