Philips Jack Dry FC6080 User manual

Jack Dry
FC6080

2

3

4

ENGLISH 6
POLSKI 14
ROMÂNĂ 21
РУССКИЙ 29
ČESKY 38
MAGYAR 46
SLOVENSKY 53
УКРАЇНСЬКІЙ 61
HRVATSKI 69
EESTI 76
LATVISKI 83
LIETUVIŠKAI 90
SLOVENŠČINA 97
FC6080

Important
◗Read these instructions for use carefully and
look at the illustrations before you start using
the appliance.
◗Always switch the vacuum cleaner off after
use.
◗Never suck up water (or any other liquid).
Never suck up ashes until they are cold.
◗Do not let water enter the vacuum cleaner or
the wall holder. Never immerse the vacuum
cleaner or the wall holder in water.
◗The charger plug feels warm.This is normal.
◗Only charge the vacuum cleaner with the
charger supplied.
◗Do not use the appliance if it is damaged.Take
it to an authorised Philips service centre for
repair.
Preparing the appliance for use
C◗Wind and store excess mains cord in the wall
holder.
C◗Screw the wall holder to the wall with the
screws supplied with the appliance.
◗You can also place the vacuum cleaner and
the wall holder flat on a table during charging.
ENGLISH6

C◗The crevice tool, floor nozzle and the stick
can be attached to the wall holder by pushing
them into the appropriate fastening slots.
Charging the appliance
1Make sure that the slide switch of the
vacuum cleaner is in off position (0) during
charging.The appliance will not charge if
the slide switch is in another position.
2Insert the charger plug into the wall
socket.
C3Always put the vacuum cleaner back onto
the holder after use to recharge the
batteries, even if the batteries are still
almost fully charged.
C◗The indicator light will come on to indicate
that the appliance is charging.
The indicator light will stay on as long as the
appliance is connected to the wall holder and the
plug is in the wall socket.
The indicator light does not give any information
about the charge level of the built-in batteries.
Charge the appliance for at least 16 hours before
you use it for the first time.
Recharge the appliance as soon as the motor
power decreases noticeably.
ENGLISH 7

If you are not going to use the appliance for a
longer period of time, we advise you to remove
the charger plug from the wall socket to save
energy.
Vacuum cleaning
C1Set the slide switch to position I for
normal suction power.
Connecting accessories
Hard floors and carpets
C1Use the floor nozzle to vacuum clean hard
floors and carpets.
Fluff and hair
C1The floor nozzle and the dust
compartment are equipped with a fluff
collector.You can use the fluff collector to
remove hair or fluff.
Pass the fluff collector gently over the hairs or fluff
to be removed.The hairs or fluff will be worked
loose from the surface, collected and then sucked
up.
ENGLISH8

Hard-to-reach places
C1Use the crevice tool to vacuum clean
hard-to-reach places.
Extra reach
C1You can assemble the stick for extra reach
when cleaning hard floors, carpets and
hard-to-reach areas. Push the narrow part
of the stick into the hole in the handle
until you hear a click.
C◗You can switch the appliance on by means of
the slide switch on the handle of the stick.
C2To detach the stick, press the release
button underneath the handle of the
vacuum cleaner and pull the stick out of
the appliance.
ENGLISH 9

Emptying the dust compartment
C1Press the break button and open the
vacuum cleaner over a dustbin.
C2Remove the filter from the dust
compartment.
3Clean the filter and empty the dust
compartment.
◗Clean the filter with a brush or with a normal
vacuum cleaner if it is very dirty.
Replacing the filter
Replace the filter if it can no longer be cleaned
properly (usually after having been cleaned
50 times).
C1Remove the filter frame from the dust
compartment.
C2Gently turn the filter clockwise to detach
it from the frame.
ENGLISH10