Phoenix Mecano OKIN REFINED RF28 User manual

Issue Department：Date：2018.11.15
System Instruction Author：
Instruction of RF28 Edition：1.1
Page 1 of 4
1/4
Instruction of RF28
1 Key description
1.1 appearance

Figure1buttonofremote
2.5 Head up 2.6 Head down
2.7 Foot up 2.8 Foot down
2.9 Flat
2.1 ZG button
2.3 Memory A button
2.2 AntiSnore button 2.10 Under bed light

Issue Department：Date：2018.11.15
System Instruction Author：
Instruction of RF28 Edition：1.1
Page 2 of 4
2/4
2 Key description
2.1 ZG button
Click the ZG button, the actuator moves to ZG position, stop when click any button during the
movement;
Press and hold the ZG button for 5s, timer LED of remote flashes, the control box records
current position as ZG position;
When in the process of movingto memory positions, the head and foot actuatorsmove first,
then the tilt and lumbar actuators move;
2.2 AntiSnore button
Click AntiSnore button, actuators move to AntiSnore position, stop when click any button
during movement；
Press and hold AntiSnore button for 5s, timer LED of remote flashes, the control box records
current position as AntiSnore position;
When in the process of moving to memory positions, the head and foot actuators move first,
then the tilt and lumbar actuators move;
2.3 Memory A button
Click MA button, actuators move to MA position, stop when click any button during
movement；
Press and hold MAbutton for 5s, timer LED of remote flashes, the control box records current
position as MA position;
When in the process of moving to memory positions, the head and foot actuators move first,
then the tilt and lumbar actuators move;
2.4 Reset all memory positions to default settings
Pressa and hold ZG+FLAT buttonsfor 5s, timer LED of remote flashes, the control box reset
all memory positions to default settings；

Issue Department：Date：2018.11.15
System Instruction Author：
Instruction of RF28 Edition：1.1
Page 3 of 4
3/4
2.5 Head up
Press and hold HEAD UP button of remote, head actuator moves out, stop when
released；
2.6 Head down
Press and hold HEAD DOWN button of remote, head actuator moves in, stop when released；
2.7 Foot up
Pressa and hold FOOT UP button of remote, foot actuator moves out, stop when released;
2.8 Foot down
Press and hold FOOT DOWN button of remote, foot actuator moves in , stop when released；
When moving to flat position, lumbar actuator and tilt actuator move first, after 500ms, head
andfoot actuators start moving;
2.9 Flat
Click FLAT button, the bed goes flat, stop when click any button during the process of going flat；
2.10 Under bed light
Click the under bed light button, the under bed light switch its on/off state; After the under bed
light opens, if do not manually close, it will automatically turn off after 5 minutes;

Issue Department：Date：2018.11.15
System Instruction Author：
Instruction of RF28 Edition：1.1
Page 4 of 4
4/4
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de
licence.L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment.The device has been evaluated to meet general RF exposure requirement.
Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour fac un
autre environnement.ce dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux
rf.
FCC Statement ：
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.

FCC ID: PCU-RF28
IC: 21319-RF28
FCC ID: PCU-CB1220
IC: 21319-CB1220