Phoenix DryTAG RH User manual

DryTAG RH Temp/RH Sensor
QUICK START GUIDE
SETUP
Thank you for purchasing a Phoenix DryTAG RH Bluetooth Beacon. Please follow
these steps to successfully locate your DryTAG RH, add it to a piece of equipment
and add that equipment to your inventory in the DryLINK® Mobile App. For a more
information on DryLINK and the entire Ecosystem,
visit www.usephoenix.com/phoenix-drylink-mobile-app/.
Scan QR code
for more
information on
DryLINK®
TS-1188 08/20 Rev A
USEPHOENIX.COM |800-533-7533
Tighten the screws if
needed
Pull out the battery tab to
activate the battery

QUICK START GUIDE
DryTAG RH Temp/RH Sensor
USEPHOENIX.COM |800-533-7533
A blue box will appear
at the bottom of
the screen if a new
(unclaimed) DryTAG RH
is in range.
Click “View Units” to
select the DryTAG RH
you are installing.
After you select the unit and
click “add,” you will see all of
your non-smart equipment
options.
Add any mounted DryTAG RH to
the correct dehumidifier.
For all non-smart dehumidifiers
not included in the DryLINK
app, click “Add New
Equipment” and add them to
your inventory.
If you want to use the DryTAG
RH as a standalone
thermo-hygrometer, also click
“Add New Equipment.”
The DryTAG RH can be permanently attached to the outlet of a dehumidifier or used as a standalone
thermo-hygrometer to automate the readings for an affected area, unaffected area, or HVAC.
If you choose to mount the DryTAG RH on a dehumidifier, please see our mounthing instruction before continuing.
Adding your DryTAG RH in the DryLINK app
• Once the unit is mounted, open the DryLINK app.
• Add DryTAG RH to your inventory as a standalone thermo-hygrometer or as an outlet reader for any
dehumidifier.

QUICK START GUIDE QUICK START GUIDE
DryTAG RH Temp/RH Sensor
USEPHOENIX.COM |800-533-7533
After clicking “Add New
Equipment” either
select dehumidifier or
meter and fill in the
information.
If you select a
dehumidifier to add the
DryTAG RH to, you will
see this screen. Click
“OK.”
After clicking “OK” it
will become associated
with the selected
dehumidifier in your
inventory and will
provide readings
automatically.

QUICK START GUIDE
DryTAG RH Temp/RH Sensor
USEPHOENIX.COM |800-533-7533
If the DryTAG RH is
added as a standalone
thermo-hygrometer,
it will appear under
your Company Units
inventory tab.
When using the
DryTAG RH on a job
as a standalone
thermo-hygrometer,
click on the affected,
unaffected or HVAC.
You will be shown a list
of smart equipment
to which the DryTAG
RH can be assigned to
take readings.
Select the unit for
which the DryTAG
RH will be gathering
readings. Data will
be gathered for the
remainder of the job
it’s associated with
and provide the same
readings on future
visits.
The DryTAG RH is meant to be permanently used as either the outlet for a dehumidifier or as a stand alone
Thermo-Hygrometer. To change how it is used, go to the equipment details, click the ellipsis, and click remove DryTAG
RH. Delete it from your inventory. If you do not click “Remove DryTAG” first, it will remember the original association
and not allow you to change it. Additionally, the DryTAG RH may take up to 15 minutes to pop up the blue box
allowing you to add the unit again.