Pickering 40-567A User manual

pickeringtest.com
Issue 1.1 March 2023
40-567A User Manual
PXI 1-Pole 2 A BRIC™ Multi-Slot Matrix Module

Page (II) PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering
Page (II) REED RELAY MODULE 40-110/115/120/125
pickering
© COPYRIGHT (2023) PICKERING INTERFACES. ALL RIGHTS RESERVED.
No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by
any means without the written permission of Pickering Interfaces.
Technical details contained within this publication are subject to change without notice.
ISO 9001
Reg No. FM38792

Page (III)
PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering
Page (III)
REED RELAY MODULE 40-110/115/120/125
pickering
TECHNICAL SUPPORT
For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.
WARRANTY
All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of
three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be
defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.
Products serviced and repaired outside of the warranty period are warranted for ninety days.
Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.
ENVIRONMENTAL POLICY
Pickering Interfaces operates under an environmental management system similar to ISO 14001.
Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the
environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and
safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can
be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.
Worldwide Technical Support and Product Information
pickeringtest.com
Germany
Tel: [phone]
E-mail: [email protected]
Sweden
Tel: [phone]
E-mail: [email protected]
USA
Tel: (West) [phone]
Tel: (East) [phone]
E-mail: [email protected]
Czech Republic
Tel: [phone]
E-mail: [email protected]
France
Tel [phone]
E-mail [email protected]
Pickering Interfaces Headquarters
Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom
Tel: [phone]
E-Mail: [email protected]
China
Tel: [phone]
E-mail: [email protected]

Page (IV) PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering
Page (IV) REED RELAY MODULE 40-110/115/120/125
pickering
MEANING / DESCRIPTION SYMBOL
PROTECTIVE EARTH (GROUND)
To identify any terminal which is intended for connection to an external conductor for
protection against electric shock in case of a fault, or the terminal of a protective earth
(ground) electrode.
DANGEROUS VOLTAGE
To indicate hazards arising from dangerous voltages.
WARNING / CAUTION
An appropriate safety instruction should be followed or caution to a potential hazard
exists.
Refer to the relevant instructions detailed within the product manual.
HEAVY
If this product is heavy reference should be made to the safety instructions for
provisions of lifting and moving.
STATIC SENSITIVE
To indicate that static sensitive devices are present and handling precautions should
be followed.
!
kg
SAFETY SYMBOLS
PRODUCT SAFETY
The following safety symbols may be used on the product and throughout the product documentation.

Page (V)
PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering
Copyright Statement ...................................................................II
Technical Support and Warranty................................................III
Product Safety .............................................................................IV
Contents (this page)....................................................................V
Warnings and Cautions ..............................................................VII
Section 1
Technical Specication...............................................................1.1
Section 2
Technical Description .................................................................2.1
Mechanical Description ........................................................2.1
Functional Description .........................................................2.1
Section 3
Installation....................................................................................3.1
Pre Operation Checks...........................................................3.1
Hardware Installation ............................................................3.2
Software Installation .............................................................3.2
Testing Operation ..................................................................3.3
Section 4
Programming Guide....................................................................4.1
Programming Options for PXI Modules ..............................4.1
Module Architecture..............................................................4.2
Programming The Module ....................................................4.3
Setting an X-X Connection ...................................................4.4
Using Pickering Drivers in LabVIEW ...................................4.5
Section 5
Connector Information................................................................5.1
Section 6
Troubleshooting ..........................................................................6.1
Section 7
Maintenance Information............................................................7.1
Switching System Test Tools ...............................................7.1
Fuse Replacement.................................................................7.1
Relay Fault Finding ...............................................................7.2
Module Removal From Chassis ...........................................7.12
Card Removal From BRIC.....................................................7.14
Card Replacement.................................................................7.16
CONTENTS

Page (VI) PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering
THIS PAGE INTENTIONALLY BLANK

Page (VII)
PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering
Page (VII)
2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579
pickering
WARNINGS AND CAUTIONS
WARNING - HAZARDOUS ENVIRONMENTS SYMBOL
This product is not specically designed for use in hazardous environments, for example in explosive
atmospheres. If the product is to be used in hazardous environments we recommend that the user
ensures suitable protective measures are taken.
!
WARNING - DANGER OF ELECTRIC SHOCK SYMBOL
This module may contain hazardous voltages. Before removing the module from the rack remove all
supplies and disconnect user I/O signals.
Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O
signals that may be present. Blanking panels are available to order from Pickering in a variety of
slot widths. If the product is not used in this manner for example by using an extender card then
additional care must be taken to avoid contact with exposed signals.
Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.
This module must not be used for the switching of Mains Circuits. For the switching of voltages up
to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must
be fully isolated from the Mains Circuit and the safety earth.
The host chassis must be correctly installed and be connected to mains or factory safety ground,
please refer to your chassis installation manual.
Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT
For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage
Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved
by a transformer in which the primary windings are separated from the secondary windings by
reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.
CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL
Certain semiconductor devices used in this equipment are liable to damage due to static voltage.
Observe the following precautions when handling these devices in their unterminated state, or
sub-assemblies containing these devices:
1. Persons removing sub-assemblies from equipment using these devices must be earthed by a
wrist strap and a resistor at the point provided on the equipment.
2. Soldering irons used during the repair operations must be low voltage types with earthed tips and
isolated from the mains voltage by a double insulated transformer.
3. Outer clothing worn must be unable to generate static charges.
4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in
anti-static bags.
PXI Switching
Module
Device
Under Test
Power
Supply
Power
Supply
Host Chassis
Secondary Circuit
Mains
Circuit
Mains
Circuit
Mains/Factory
Safety Ground

Page (VIII) PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering
Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579
pickering
CAUTION - PRODUCT DOCUMENTATION SYMBOL
Suitably qualied & trained users should ensure that the accompanying documentation is fully read
and understood before attempting to install or operate the product.
!
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O
signals (refer to the Maintenance Section).
• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or
the combined weight of the modules & chassis.
• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the
chassis and the user I/O signals.
• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.
• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on
the front of the unit.

Page 1.1
PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering SECTION 1 - TECHNICAL SPECIFICATION
SECTION 1 - TECHNICAL SPECIFICATION
Updated Product Information
These products have been introduced as a “form & fit” update
to the 40-567 range, the electrical performance is very similar
and the software and pinout are identical.
40-567A-108 352x8 Matrix Switching Diagram (Fully Populated BRIC8)
The 40-567A supports 8 concurrent switch paths for X to X (see application diagram overleaf)
Supported by eBIRST
eBIRST switching system test tools simplify switching
system fault-finding by quickly testing the system and
graphically identifying the faulty relay.
For more information go to: pickeringtest.com/ebirst
The 2 A Matrix BRIC is a higher power/voltage version of
Pickering’s established range of PXI Matrix BRIC modules.
It features higher voltage, current and power handling
capability than the ultra high density reed relay based BRICs.
It is not as suited to switching low level signals, where
Ruthenium Reed Relays are a better choice and have a very
long lifetime of up to 1000 million operations. For superior low
level switching please refer to our 40-560B/561A/562B range.
yVery High Density 2A Matrix With Up To
704 Crosspoints Per 2-Slot BRIC,
1408 Crosspoints Per 4-Slot BRIC &
2816 Crosspoints Per 8-Slot BRIC
(352 Crosspoints Per PXI Slot)
yIntegrated PXI Module With Built In High
Performance Screened Analog Bus
y2-Slot Configurations to 88x8 (1-Pole),
4-Slot Configurations to 176x8 (1-Pole) &
8-Slot Configurations to 352x8 (1-Pole)
ySwitch up to 100 VDC/70 VAC, 2 A, 60 W
yAutomatic Analog Bus Isolation Switching
Maximizes Bandwidth and Matrix Reliability
yDrivers Supplied for Windows & Linux, Plus
Support for Real-time Systems
ySupported by PXI or LXI Chassis
ySupported by
eBIRST ™
y3 Year Warranty
BRIC™ 2nd Generation PXI 2 A Switch Matrix
The 40-567A BRIC is a range of high density matrix modules
able to switch up to 2 A or 100 VDC/70 VAC. The 40-567A BRIC
modules are available in 2, 4 or 8-slot sizes to suit most high
performance PXI matrix requirements, constructed using
high quality electro-mechanical relays for high switching
confidence.
Typical applications include signal routing for functional ATE
systems. With its high level of switching density, 40-567A
matrix modules allow a complete functional ATE system to be
housed in a single 3U PXI chassis, BRIC modules allow the use
of a much lower cost 8-slot PXI chassis.
High Reliability and Easy of Use
The 40-567A PXI BRIC is designed to minimise the cost and
complexity of cable assemblies to the device under test and
instrumentation. Analog busing is housed within the module
using a high performance screened analog backplane.
Pickering can construct custom cable assemblies for all
of our PXI modules, please contact sales office for further
assistance.
Pickering’s Range of 2 A BRIC Matrix Modules
Model No. Poles Y-Bus Size Min. Matrix
Size
Max. Matrix
Size
40-568 1 4 75x4 600x4
40-596 1 6 58x6 464x6
40-567A 1 8 44x8 352x8
40-597 1 12 32x12 256x12
40-598 1 16 24x16 192x16
40-566A 2 4 55x4 385x4
40-565A 2 8 24x8 192x8
pickeringtest.com
40-567A
PXI 1-Pole 2 A BRIC™ Multi-Slot Matrix
Issue 1.0 January 2023

Page 1.2 PXI 1-Pole 2 A BRIC Multi-Slot Matrix 40-567A
pickering
SECTION 1 - TECHNICAL SPECIFICATION
Example Application of the 40-567A 1-Pole 2A BRIC Matrix
Instrument 1 Instrument 2 Instrument 3
1 2 3 4 5 6 7 8 9 10 11 12
Instrument 4 Instrument 5
20 21 22 23 24 25 26 27 28 29 30 31 32
Device Under Test No. 1
33 34 35 36 37 38 39 40 41 42 43 44 45
Device Under Test No. 2
46 47 48 49 50 357 350 351 352
DUT No. 3
Schematic diagram showing a 352x8 BRIC Matrix being used to parallel test multiple DUTs.
The BRIC Matrix allows tremendous test system flexibility.
X1 X44
X176
X1
MATRIX
CROSSPOINT
x8
X1 X44
X352
X1
MATRIX
CROSSPOINT
x8
The 40-567A in BRIC4 Format is Available With Matrix Configurations Between 44x8 and 176x8
The 40-567A in BRIC8 Format is Available With Matrix Configurations Between 44x8 and 352x8
X1 X44
X88
X1
MATRIX
CROSSPOINT
x8
The 40-567A in BRIC2 Format is Available With Matrix Configurations of 44x8 and 88x8
40-567A
pickeringtest.com
Page 2
PXI 1-Pole 2 A BRIC™ Multi-Slot Matrix