Pickering 60-890-005 User manual

pickeringtest.com
Issue 1.1 August 2020
60-890-005 User Manual
LXI 40GHz SPDT & SP6T Terminated Microwave Switch

Page (II)
pickering
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
Page (II) REED RELAY MODULE 40-110/115/120/125
pickering
© COPYRIGHT (2020) PICKERING INTERFACES. ALL RIGHTS RESERVED.
No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by
any means without the written permission of Pickering Interfaces.
Technical details contained within this publication are subject to change without notice.
ISO 9001
Reg No. FM38792

Page (III)
pickering
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
Page (III)
REED RELAY MODULE 40-110/115/120/125
pickering
TECHNICAL SUPPORT
For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.
WARRANTY
All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of
three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be
defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.
Products serviced and repaired outside of the warranty period are warranted for ninety days.
Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.
ENVIRONMENTAL POLICY
Pickering Interfaces operates under an environmental management system similar to ISO 14001.
Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the
environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and
safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can
be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.
Worldwide Technical Support and Product Information
pickeringtest.com
Germany
Tel: [phone]
E-mail: [email protected]
Sweden
Tel: [phone]
E-mail: [email protected]
USA
Tel: (West) [phone]
Tel: (East) [phone]
E-mail: [email protected]
Czech Republic
Tel: [phone]
E-mail: [email protected]
France
Tel [phone]
E-mail [email protected]
Pickering Interfaces Headquarters
Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom
Tel: [phone]
E-Mail: [email protected]
China
Tel: [phone]
E-mail: [email protected]

Page (IV)
pickering
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
Page (IV) REED RELAY MODULE 40-110/115/120/125
pickering
MEANING / DESCRIPTION SYMBOL
PROTECTIVE EARTH (GROUND)
To identify any terminal which is intended for connection to an external conductor for
protection against electric shock in case of a fault, or the terminal of a protective earth
(ground) electrode.
DANGEROUS VOLTAGE
To indicate hazards arising from dangerous voltages.
WARNING / CAUTION
An appropriate safety instruction should be followed or caution to a potential hazard
exists.
Refer to the relevant instructions detailed within the product manual.
HEAVY
If this product is heavy reference should be made to the safety instructions for
provisions of lifting and moving.
STATIC SENSITIVE
To indicate that static sensitive devices are present and handling precautions should
be followed.
!
kg
SAFETY SYMBOLS
PRODUCT SAFETY
The following safety symbols may be used on the product and throughout the product documentation.

Page (V)
pickering
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
Copyright Statement ......................................................................II
Technical Support and Warranty..................................................III
Product Safety .............................................................................. IV
Contents (this page)...................................................................... V
Warnings and Cautions .............................................................. VII
Section 1
Technical Specication...............................................................1.1
Section 2
Technical Description .................................................................2.1
Functional Description ....................................................2.1
Section 3
Installation....................................................................................3.1
Pre Operation Checks .....................................................3.1
Hardware Installation.......................................................3.1
Setting The IP Address ....................................................3.2
Installing The Software....................................................3.3
Soft Front Panel Operation .............................................3.3
Section 4
Programming Guide....................................................................4.1
Programming Options for LXI Units...............................4.1
Programming the Microwave Switch .............................4.2
Command Line Control ...................................................4.6
Using The Soft Front Panel...........................................4.13
Section 5
Connections.................................................................................5.1
Section 6
Trouble Shooting .........................................................................6.1
LXI Status Indicators .......................................................6.1
LAN Reset.........................................................................6.2
Section 7
Maintenance Information............................................................7.1
Microwave Switch Parts List...........................................7.2
General Maintenance.......................................................7.5
RF Relay Removal/Retting ............................................7.8
Appendix A
Fitting Rack Mounting Flanges .................................................A.1
CONTENTS

Page (VI)
pickering
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
THIS PAGE INTENTIONALLY BLANK

Page (VII)
pickering
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
Page vii
LXI HIGH VOLTAGE 2-POLE MATRIX 60-310
pickering
WARNINGS & CAUTIONS
WARNING - HAZARDOUS ENVIRONMENTS SYMBOL
This product is not specically designed for use in hazardous environments, for example in explosive
atmospheres. If the product is to be used in hazardous environments we recommend that the user
ensures suitable protective measures are taken.
!
CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL
Certain semiconductor devices used in this equipment are liable to damage due to static voltage.
Observe the following precautions when handling these devices in their unterminated state, or
sub-assemblies containing these devices:
1. Persons removing sub-assemblies from equipment using these devices must be earthed by a
wrist strap and a resistor at the point provided on the equipment.
2. Soldering irons used during the repair operations must be low voltage types with earthed tips and
isolated from the mains voltage by a double insulated transformer.
3. Outer clothing worn must be unable to generate static charges.
4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in
anti-static bags.
WARNING - DANGER OF ELECTRIC SHOCK SYMBOL
This unit may contain hazardous voltages. Before removing the unit from the rack remove all supplies
and disconnect user I/O signals.
If the unit has removable modules, unused slots in the chassis must be populated with blanking
panels to prevent access to user I/O signals that may be present. Blanking panels are available to
order from Pickering. If the product is not used in this manner for example by using an extender card
then additional care must be taken to avoid contact with exposed signals.
Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.
This unit must not be used for the switching of Mains Circuits. For the switching of voltages up to the
unit’s full specication, Secondary Circuit power supplies and the Device Under Test must be fully
isolated from the Mains Circuit and the safety earth.
The chassis must be correctly installed and be connected to mains or factory safety ground,
please refer to the installation section of this manual.
Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT
For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage
Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved
by a transformer in which the primary windings are separated from the secondary windings by
reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.
Switching
Function
Device
Under Test
Power
Supply
Power
Supply
LXI Unit’s Chassis
Secondary Circuit
Mains
Circuit
Mains
Circuit
Mains/Factory
Safety Ground

Page (VIII)
pickering
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
WARNING
Only the correct SMA connector series should be mated with this unit. SMA-2.9 connectors
are used and the user should only mate the correct type to the unit, failure to do so may
result in damage to the connector.
Also, it is important that the SMA connector’s nut is properly tightened to the correct torque
with a 5/16 inch wrench. This should be 3-5 in·lbs (0.3 to 0.6 N·m) for brass, and 7-10 in·lbs
(0.8–1.1 N·m) for stainless steel connectors.
!
Page viii
LXI HIGH VOLTAGE 2-POLE MATRIX 60-310
pickering
CAUTION - PRODUCT DOCUMENTATION SYMBOL
Suitably qualied & trained users should ensure that the accompanying documentation is fully read
and understood before attempting to install or operate the product.
!
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O
signals (refer to the Maintenance Section).
• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or
the combined weight of the modules & chassis.
• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the
chassis and the user I/O signals.
• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.
• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on
the front of the unit.
WARNING - RACK MOUNTING
If it is required to t this unit into a 19 inch rack, its weight must be
supported by side brackets, runners or a suitable equipment shelf.
The xing holes in the front panel anges are designed only for
securing the device in the rack and must NOT be used to support
the weight of the whole device.
Please refer to Appendix A for the procedure for tting the
supplied anges to either side of the front panel.
!
HIGH VOLTAGE SAFETY WARNING
THIS UNIT IS CAPABLE OF SWITCHING VOLTAGES AND CURRENTS THAT CAN
CAUSE SERIOUS INJURIES. IN APPLICATIONS INVOLVING HIGH VOLTAGES IT
IS STRONGLY RECOMMENDED THAT UNUSED CONNECTORS ARE CAPPED
TO PREVENT ACCIDENTAL CONTACT WHILE IN USE. SYSTEM INTEGRATORS
AND USERS SHOULD CONNECT TO THE FRONT PANEL CONNECTORS WITH
CONNECTORS OR CABLE ASSEMBLIES THAT ENSURE OPERATORS WILL NOT
INADVERTENTLY COME IN CONTACT WITH HIGH VOLTAGES.

Page 1.1
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
pickering SECTION 1 - TECHNICAL SPECIFICATION
SECTION 1 - TECHNICAL SPECIFICATION
pickeringtest.com
LXI 40GHz SPDT & SP6T Microwave Switch 60-890-005
ISSUE 1.0 AUG 2020
• High Performance Microwave Switches
• 40GHz Bandwidth
• 3 Banks of SPDT & 4 Banks of SP6T Switches
• Unused Signals Terminated into 50Ω
• Excellent RF & Repeatability Characteristics
• Field Upgradeable to Maximum Loading
• LED Indication
• Compact 2U Form Factor
• LXI Standard 1.4 Compliant
• IVI & Direct I/O Drivers
• 3 Year Warranty
Schematic Diagram for the 60-890-005 40GHz Terminated Microwave Switch - 3xSPDT & 4xSP6T
The 60-890-005 Microwave Switch is suitable for switching 50Ω
signals up to 40GHz. With 3 banks of SPDT and 4 banks of
SP6T it is ideal for constructing complex microwave switching
systems. Additional relays can be tted to a maximum loading of 6
banks of SPDT and 6 banks of SP6T. All unused signal paths are
automatically connected to 50Ω terminations. Signal connections
are by front panel mounted SMA-2.9 connectors.
The switch has an extremely high level of performance with low
VSWR, very high isolation, low loss and high power handling.
It is ideal for switching 50Ω systems for HF up to microwave
frequencies. It occupies 2U of rack space, providing a compact
switching solution.
Controlling the Switch
The 60-890-005 is controlled through an LXI interface based on
Ethernet 1000Base-T. This provides a quick and easy method of
installing the 60-890-005 and a simple way of controlling the unit
from a remote location through its API or built in soft front panel.
The ability to control the unit at a distance allows the testing of
systems without the need for a physical presence.
Other Microwave Switching Configurations
We are able to offer other microwave switching solutions, if you
have a custom requirement for switching please contact your local
Pickering Interfaces sales representative.
NC
Com
NO
NC
Com
NO
Terminated SPDT Switch 1
Terminated SPDT Switch 2
NC
Com
NO
Terminated SPDT Switch 3
Com 1
2
3
4
5
6
Terminated SP6T Switch 4
Com 1
2
3
4
5
6
Terminated SP6T Switch 3
Com 1
2
3
4
5
6
Terminated SP6T Switch 2
Com 1
2
3
4
5
6
Terminated SP6T Switch 1

Page 1.2 LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
pickering
SECTION 1 - TECHNICAL SPECIFICATION
SPDT & SP6T Microwave Switch – 60-890-005
pickeringtest.com
Specifications
RF Specification - SP6T Terminated Switch
Characteristic Impedance: 50Ω
Connectors: SMA-2.9
Bandwidth DC to 40GHz
Isolation: 70dB (0-6GHz)
60dB (6-12.4GHz)
60dB (12.4-18GHz)
55dB (18-26.5GHz)
50dB (26.5-40GHz)
Insertion Loss: 0.2dB (0-6GHz)
0.4dB (6-12.4GHz)
0.5dB (12.4-18GHz)
0.7dB (18-26.5GHz)
1.1dB (26.5-40GHz)
VSWR: 1.3:1 (0-6GHz)
1.4:1 (6-12.4GHz)
1.5:1 (12.4-18GHz)
1.7:1(18-26.5GHz)
2.2:1 (26.5-40GHz
Maximum RF Carry Power: 40W (0-6GHz)
30W (6-12.4GHz)
25W (12.4-18GHz)
15W (18-26.5GHz)
5W (26.5-40GHz)
Termination power rating: 1W per termination,
3W total per 6 channel multiplexer
Expected Life (Low Power): >2 million operations per position
General Specification - SP6T Terminated Switch
Relay Manufacturer: Radiall
Conguration: SP6T Terminated Microwave
Multiplexer.
Indicators: Blue LEDs to indicate a
closed RF path.
Operate Time: Typically 15ms
RF Specification - SPDT Terminated Switch
Characteristic Impedance: 50Ω
Connectors: SMA-2.9
Bandwidth DC to 40GHz
Isolation: 70dB (0-6GHz)
60dB (6-12.4GHz)
60dB (12.4-18GHz)
55dB (18-26.5GHz)
50dB (26.5-40GHz)
Insertion Loss: 0.3dB (0-6GHz)
0.4dB (6-12.4GHz)
0.5dB (12.4-18GHz)
0.7dB (18-26.5GHz)
0.8dB (26.5-40GHz)
VSWR: 1.3:1 (0-6GHz)
1.4:1 (6-12.4GHz)
1.5:1 (12.4-18GHz)
1.7:1(18-26.5GHz)
1.9:1 (26.5-40GHz
Average RF Carry Power: 80W (0-6GHz)
60W (6-12.4GHz)
50W (12.4-18GHz)
20W (18-26.5GHz)
10W (26.5-40GHz)
Termination power rating: 1W per termination,
Expected Life (Low Power): 2 million operations
General Specification - SPDT Terminated Switch
Relay Manufacturer: Radiall
Conguration: SPDT Terminated Microwave
Switch.
Indicators: Blue LED to indicate switch is
activated.
Operate Time: <10ms

Page 1.3
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
pickering SECTION 1 - TECHNICAL SPECIFICATION
SPDT & SP6T Microwave Switch – 60-890-005
pickeringtest.com
Specifications
Power Source
Universal AC mains supply, 90-120/200-240V 50-60Hz
Power Inlet: Male IEC connector
Power Rating: 100VA maximum
Fuse Rating: 5A, 250V
LAN Interface
Compliant to LXI Standard 1.4, the 60-890-005 has a 1000Base-T
Ethernet Interface via a standard RJ-45 connector mounted on the
rear panel with an LCD display showing the unit’s IP address.
Mechanical Characteristics
Supplied with front panel ears to enable rack mounting on a shelf or
other rear support mechanism.
Dimensions: 2U high, full 19” rack width, 500mm depth
3D models for all versions in a variety of popular le formats are
available on request.
Connectors
Signals via front panel SMA-2.9 connectors.
Cooling
Fan assisted cooling, side air intakes and rear exhaust.
LXI Status Indicators
Front panel mounted LEDs:
• Power
• Ready
• Error
• LAN
• Active
Operating/Storage Conditions
Operating Conditions
Operating Temperature:
Humidity:
Altitude:
0°C to +55°C
Up to 90% non-condensing
5000m
Storage and Transport Conditions
Storage Temperature:
Humidity:
Altitude:
-20°C to +75°C
Up to 90% non-condensing
15000m
Safety & CE Compliance
All products are fully CE compliant and meet applicable EU
directives: Low-voltage safety EN61010-1:2010, EMC Immunity
EN61326-1:2013, Emissions EN55011:2009+A1:2010.

Page 1.4 LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
pickering
SECTION 1 - TECHNICAL SPECIFICATION
SPDT & SP6T Microwave Switch – 60-890-005
pickeringtest.com
Ordering Information
Mating Connectors & Cabling
For connection accessories for the 60-890-005 please refer to the
90-011D RF Cable Assemblies data sheet where a complete list
and documentation can be found for accessories, or refer to the
Connection Solutions catalog.
Product Order Codes
LXI 40GHz 3xSPDT & 4xSP6T
Terminated Microwave Switch, 50Ω 60-890-005
Versions with other bank counts and different frequency ranges
can be made to order, please contact sales ofce.
Additional Switch Order Codes:
SPDT, Terminated, 40GHz Assembly
SP6T, Terminated, 40GHz Assembly
91-100-106
91-100-107
Product Customization
Pickering LXI units are designed and manufactured on our own
exible manufacturing lines, giving complete product control and
enabling simple customization to meet very specic requirements.
Customization can include:
• Alternative relay types
• Mixture of relay types
• Alternative number of relays
• Different performance specications
All customized products are given a unique part number, fully
documented and may be ordered at any time in the future. Please
contact your local sales ofce to discuss.
Further LXI RF Switching Solutions from
Pickering Interfaces
60-891 LXI 36:1 Microwave Multiplexer.
Available With SMA Connectors (18GHz) or BNC
Connectors (4GHz).
60-721A LXI 72-Channel High Performance Video
Multiplexer with a 1GHz bandwidth.
60-750/751 LXI Microwave Matrix. Bandwidth up to
20GHz and is available in sizes from Single 3x3 up to
Dual 4x4 with Loop-Thru and termination options.
60-801/802 LXI Microwave Multiplexer, up to 40GHz
bandwidth and support for up to 16 banks of 6 or 4
way multiplexers.

Page 1.5
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
pickering SECTION 1 - TECHNICAL SPECIFICATION
SPDT & SP6T Microwave Switch – 60-890-005
pickeringtest.com
Supporting Products & Software
We also offer customized cabling and have a free online Cable Design Tool that can
be used to create custom cable solutions for many applications.
Visit: pickeringtest.com/cdt to start your design.
Mass Interconnect
We recommend the use of a mass interconnect solution when an Interchangeable
Test Adapter (ITA) is required for a PXI or LXI based test system. Our modules are
fully supported by both Virginia Panel and MacPanel.
Pickering Reed Relays
We are the only switch provider with in-house reed relay manufacturing capability
via our Relay Division. These instrument grade reed relays feature SoftCenter™
technology, ensuring long service life and repeatable contact performance.
To learn more, please go to: pickeringrelay.com
Connectivity Solutions
We provide a full range of supporting cable and connector solutions for all our switching products—20 connector families with 1200+
products. We offer everything from simple mating connectors to complex cables assemblies and terminal blocks. All assemblies are
manufactured by Pickering and are guaranteed to mechanically and electrically mate to our modules.
Connectors & Backshells Multiway Cable Assemblies RF Cable Assemblies Connector Blocks
Programming
All LXI devices are supplied with built-in software drivers, web pages for conguration and soft front panels as required by the LXI
specication. A variety of drivers are provided (C, .NET, IVI, SOAP) which are compatible with all Microsoft supported versions of Windows
and popular older versions. For a list of all supporting operating systems, please see: pickeringtest.com/os
The drivers may be used in many commonly used programming environments and applications including:
• Pickering Interfaces Switch Path Manager
• National Instruments products (LabVIEW, LabWindows/CVI, Switch Executive, MAX, TestStand, VeriStand, etc.)
• Microsoft Visual Studio products (Visual Basic, Visual C++, Visual C#)
• Keysight VEE and OpenTAP
• Mathworks Matlab
• Marvin ATEasy
• MTQ Testsolutions Tecap Test & Measurement Suite
As well as various open source environments such as:
• Sharp Develop
• Dev-C++
To learn more about software drivers and development environments, please go to: pickeringtest.com/software

Page 1.6 LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
pickering
SECTION 1 - TECHNICAL SPECIFICATION
SPDT & SP6T Microwave Switch – 60-890-005
pickeringtest.com
Supporting Products & Software
© Copyright (2020) Pickering Interfaces. All Rights Reserved Pickering Interfaces maintains a commitment to continuous product development, consequently we reserve the right to vary from the description given in this data sheet.
Signal Routing Software
Our signal routing software, Switch Path Manager, automatically selects and energizes switch
paths through Pickering switching systems. Signal routing is performed by simply dening
test system endpoints to be connected together, greatly accelerating Test System software
development.
To learn more, please go to: pickeringtest.com/spm
Diagnostic Relay Test Tools
eBIRST Switching System Test Tools are designed specically for our PXI, PCI or LXI
products, these tools simplify switching system fault-nding by quickly testing the system
and graphically identifying the faulty relay.
To learn more, please go to: pickeringtest.com/ebirst
Three Year Warranty
All standard products manufactured by Pickering Interfaces are warranted against
defective materials and workmanship for a period of three years from the date of delivery to the original purchaser. Extended warranty and
service agreements are available for all our modules and systems with various levels to suit your requirements. Although we offer a 3-year
warranty as standard, we also include guaranteed long-term support—with a history of supporting our products for typically 15-20 years. To
learn more, please go to: pickeringtest.com/support
Available Product Resources
We have a large library of product resources including success stories, product and support videos, articles, as well as complete product
catalogs and product reference maps to assist when looking for the switching, simulation and cable and connector solutions you need.
We have also published handy reference books on Switching Technology and for the PXI and LXI standards.
To view, download or request any of our product resources, please visit: pickeringtest.com/resources

Page 2.1
pickering SECTION 2 - TECHNICAL DESCRIPTION
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
SECTION 2 - TECHNICAL DESCRIPTION
FUNCTIONAL DESCRIPTION
Figure 2-1. Block Diagram for the 60-890-005 Microwave Switch (3xSPDT + 4xSP6T version)
The 60-890-005 is a microwave switch with up to 6 banks of SPDT and 6 banks of SP6T under the control of an
LXI interface and is designed for the routing of signals with frequencies up to 40GHz. The individual switches can
be used in isolation or cascaded to form larger switching networks. A block diagram for a 3xSPDT + 4xSP6T switch
is shown in Figure 2-1
Control information for the switch is sent from the Embedded Processor to the two Relay Driver PCBs via a Bridge
circuit. Each Relay Driver board can control up-to 6 microwave relays and the unit can be populated with a maximum
of 6xSPDT and 6xSP6T. The Relay Driver board’s data ports are interconnected in a daisy chain and are controlled
with a serial data stream from the Bridge board. Programming information for the processor is sent to the unit via the
LAN interface from a remote computer using the unit’s unique Ethernet address. Programming documentation for
the unit as well as data for Pickering’s other LXI compatible switching products is stored in the embedded processor
and can be downloaded over the LAN interface. LXI Status LEDs on the front of the chassis indicate the condition
of the unit and the LAN connection.
Power
Supplies
LAN
Interface
PWR
RDY
ERR
LAN
ACT
Status LEDs
RJ45
Socket
Embedded
Processor
Logic
Supply
Relay Coil
Supply
Control Control Control Control
Bridge
Board
Control Control Control Control Control Control
Control Control
Relay Drivers #2
Relay Drivers #1
Microwave Switches & LED Indicators
3xSPDT and 4xSP6T Terminated Microwave Switches
RL1 RL2 RL3 RL7 RL8 RL9 RL10

Page 2.2
pickering
SECTION 2 - TECHNICAL DESCRIPTION
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
THIS PAGE INTENTIONALLY BLANK

Page 3.1
pickering SECTION 3 - INSTALLATION
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
INSTALLING THE MICROWAVE MULTIPLEXER
The 60-890-005 may be mounted on a desk top or tted into a standard 19 inch rack (rack mounting anges are
supplied with the unit that can be tted to the sides of the front panel). When tting into a rack it is important to
provide adequate support using side brackets or runners, the mounting holes in the front panel anges are
designed only for securing the unit in the rack and must NOT be used to support the weight of the whole
unit.
The 60-890-005 relies upon forced air cooling. Internal fans draw air through slots in the front panel and expel air
through two vents in the rear panel. When positioning the chassis, make sure that there is adequate clearance to
allow unrestricted air ow through these vents. The locations of the air intakes and outlets are shown in Figures 3-1
and 3-2.
Power is supplied to the rear of the unit using a standard IEC power lead and the power on/off switch is located next
to the power inlet socket. The unit is supplied with a suitable Earthed mains power lead, If a different lead is used it
is important to ensure that an adequate Earth connection is present. When mounted in a rack, provision should be
made to allow access to the rear of the unit. This is to enable the operation of the power on/off switch and the Reset
button. The rear panel layout is shown below.
The Microwave Switch is controlled by the host computer via an Ethernet interface. The RJ45 socket on the rear of
the unit can be connected to a hub or switch via an Ethernet cable to allow control over a local area or wide area
network. Alternatively a crossover Ethernet cable can be used to connect the unit to a laptop PC and local control
can be carried out isolated from a network. The IP address of the unit has to be manually or automatically congured
before it can be used on a network, please refer to the following section “Setting the IP Address” and the “LXI Getting
Started Guide” document to carry out this process.
Figure 3-1. Front view of the Microwave Switch in 3xSPDT & 4xSP6T format
showing intake slots for cooling air next to the microwave relays
Page 3.1
LXI HIGH VOLTAGE 2-POLE MATRIX 60-310
pickering SECTION 3 - INSTALLATION
SECTION 3 - INSTALLATION
Refer to the Warnings and Cautions at the front of this manual
The product is designed for indoor use only.
!
kg
PREOPERATION CHECKS (UNPACKING)
1. Check the module for transport damage and report any damage immediately to Pickering Interfaces.
Do not attempt to install the product if any damage is evident.
2. Ensure that the designated area for the product is of a at and solid construction to support its weight.

Page 3.2
pickering
SECTION 3 - INSTALLATION
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
Figure 3-2. Rear view of the Microwave Switch showing the mains supply connection,
LAN socket and cooling air outlets
SETTING THE IP ADDRESS
To use the 60-890-005 Microwave Switch over a LAN connection it should be set up and congured as described in
the “LXI Getting Started Guide” document.
If the IP address is to be set manually and before connecting to a network, contact your IT department so they can
give you the correct settings for:
• IP Address
• Subnet Mask
• Default Gateway
• DNS Server(s)
Once you have the required information, the IP conguration window is used to manually set the IP address. This is
shown in Figure 3-4.
The current IP address setting of the 60-890-005 is indicated on an LCD display on the rear panel of the chassis.
Incorrect setting will result in a loss of communication and may also be indicated by a red LAN LED on the front
panel. If this does occur press and hold the LAN Reset button on the back panel of the device for a full factory reset
(see Section 6 “Troubleshooting” for details).
Figure 3-3. Display for IP Address on Rear Panel

Page 3.3
pickering SECTION 3 - INSTALLATION
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
SOFT FRONT PANEL OPERATION
The 60-890-005 Microwave Switch can be programmed using the Soft Front Panel. This can be run as a Java Applet
from the device’s LXI home page. You must have the Java Runtime environment loaded from Sun Microsystems to
use this facility. This application can be downloaded from www.sun.com/java .
To access the Soft Front Panel, rst select Instrument Control from the Instrument Home Page, then click the
relevant icon in the displayed window to launch the Java applet.
For a description of the controls, refer to “Using The Soft Front Panel” at the end of Section 4.
INSTALLING THE SOFTWARE
From the device web page, select ‘Driver Download’ from the menu at the left of the page. This will retrieve the driver
from the instrument and install it on your PC.
Alternatively, the driver may be found on the DVD shipped with the product in the ‘Drivers_LXI’ folder:
Series-60-Setup.exe.
This driver may also be found on the Pickering Interfaces web-site at:
http://www.pickeringtest.info/downloads/drivers/Sys60/
or from the Software Downloads section at:
www.pickeringtest.com
Figure 3-4. Example conguration window used to manually set the IP address of a Pickering LXI device

Page 3.4
pickering
SECTION 3 - INSTALLATION
LXI 40GHz SPDT & SP6T TERMINATED MICROWAVE SWITCH 60-890-005
THIS PAGE INTENTIONALLY BLANK