PICO G3 Series User manual

For PICO G3 Series

02
11
User Guide
用户指南
19
35
ユーザーガイド
用戶指南
27
󻸛󼐘󼓿󾖴󼊷󺸣󻺋
43
คู่มือการใช้งาน
EN
CN
JP
HK
KR
TH
01

02
EN

03
EN

04
EN
Skip the prompt on the screen and enter Head Operating Mode directly after the device
is powered on;
Disconnect the controller by turning off the Bluetooth connection in "Settings" ► "Bluetooth";
Disconnect the controller by unbinding the controller in "Settings" ► “Controller”;
To bind with the controller again or switch to a new one, go to the main page and turn
on headset pairing mode in "Settings" ► “Controller”. Press the HOME button +
TRIGGER button + trackpad at the same time and hold for 10 seconds, and follow the
instructions on the headset screen.
If you are using a new controller or there is no pairing information of the controller, short
press the HOME button on the controller to enter Pairing Mode.
Note: When switching from Controller Operating Mode to Head Operating Mode, the
controller will be powered off, and the virtual controller and projection lines will disappear.
When switching to Controller Operating Mode, the head pointer will disappear and
change into a virtual controller with projection lines.
Head Operating Mode:
Note: The controller does not connect to the headset under Head Operating Mode.
Perform the following instructions on the headset.
1. Move the Pointer
Swing the headset to move the pointer at the center of the field of vision.
Detailed Description
You can control the headset with Controller Operating Mode and Head Operating Mode.
The buttons on the controller are identical to the buttons on the headset, except for the
trackpad. It is recommended to use the controller to experience a richer and more
exciting interaction and content.
If you do not want to use the controller, you can enter Head Operating Mode by following
the prompt on the screen and pressing the CONFIRM button on the headset in the
following situations:
2. Head Operating Mode
When the controller is not connected, you can turn your head and press the buttons
on the headset to operate the device.
3. Screen Re-centering in Head Operating Mode
Look straight ahead while wearing the headset, press the HOME button on the headset
for more than 1 second to recenter the screen. Adjust the interface until it is positioned
right before you in your field of vision.
4. Headset Volume Adjustment
Pressing the VOLUME button on the headset can increase or decrease the volume.
Long pressing it can adjust the volume continuously.
5. Sleep/Wake up
Method 1: After taking off the headset for a while, the system automatically enters Sleep
mode. It will wake up automatically when the headset is being put on.
Method 2: Short press the POWER button on the headset to sleep or wake up.
6. Headset Hardware Reset
If issues such as the device does not respond when short pressing the HOME button or
POWER button on the headset, or when the screen on the headset is frozen, long press
the POWER button and hold for more than 10 seconds to restart the headset.
1. Trackpad
2. APP/BACK Button
3. HOME Button
4. Status Indicator
5. Controller Lanyard Hole
6. TRIGGER Button
7. VOLUME Button
8. Battery Cove
Status Indicator
Blue flashes slowly (per 0.5 seconds): Pending pairing connection.
Blue is on/off when button is pressed/not pressed: Connected.
Blue flashes quickly (per 0.1 seconds): Low battery power.
Blue flashes slowly (per 1.5 seconds): Firmware upgrade.
HOME Button
Short press to power on the device.
Short press to return to the home screen.
Long press for 1 second to recenter the screen.
TRIGGER Button
Confirm and shoot, etc.
Its functions vary in different games and applications.
APP/BACK Button
Short press to return or go to Menu.
VOLUME Button
Short press to adjust the volume.
Long press to adjust continuously.
Trackpad
Press and hold to confirm.
Touch and slide to turn page.

05
EN
Skip the prompt on the screen and enter Head Operating Mode directly after the device
is powered on;
Disconnect the controller by turning off the Bluetooth connection in "Settings" ► "Bluetooth";
Disconnect the controller by unbinding the controller in "Settings" ► “Controller”;
To bind with the controller again or switch to a new one, go to the main page and turn
on headset pairing mode in "Settings" ► “Controller”. Press the HOME button +
TRIGGER button + trackpad at the same time and hold for 10 seconds, and follow the
instructions on the headset screen.
If you are using a new controller or there is no pairing information of the controller, short
press the HOME button on the controller to enter Pairing Mode.
Note: When switching from Controller Operating Mode to Head Operating Mode, the
controller will be powered off, and the virtual controller and projection lines will disappear.
When switching to Controller Operating Mode, the head pointer will disappear and
change into a virtual controller with projection lines.
Head Operating Mode:
Note: The controller does not connect to the headset under Head Operating Mode.
Perform the following instructions on the headset.
1. Move the Pointer
Swing the headset to move the pointer at the center of the field of vision.
Detailed Description
You can control the headset with Controller Operating Mode and Head Operating Mode.
The buttons on the controller are identical to the buttons on the headset, except for the
trackpad. It is recommended to use the controller to experience a richer and more
exciting interaction and content.
If you do not want to use the controller, you can enter Head Operating Mode by following
the prompt on the screen and pressing the CONFIRM button on the headset in the
following situations:
2. Head Operating Mode
When the controller is not connected, you can turn your head and press the buttons
on the headset to operate the device.
3. Screen Re-centering in Head Operating Mode
Look straight ahead while wearing the headset, press the HOME button on the headset
for more than 1 second to recenter the screen. Adjust the interface until it is positioned
right before you in your field of vision.
4. Headset Volume Adjustment
Pressing the VOLUME button on the headset can increase or decrease the volume.
Long pressing it can adjust the volume continuously.
5. Sleep/Wake up
Method 1: After taking off the headset for a while, the system automatically enters Sleep
mode. It will wake up automatically when the headset is being put on.
Method 2: Short press the POWER button on the headset to sleep or wake up.
6. Headset Hardware Reset
If issues such as the device does not respond when short pressing the HOME button or
POWER button on the headset, or when the screen on the headset is frozen, long press
the POWER button and hold for more than 10 seconds to restart the headset.
1. Trackpad
2. APP/BACK Button
3. HOME Button
4. Status Indicator
5. Controller Lanyard Hole
6. TRIGGER Button
7. VOLUME Button
8. Battery Cove
Status Indicator
Blue flashes slowly (per 0.5 seconds): Pending pairing connection.
Blue is on/off when button is pressed/not pressed: Connected.
Blue flashes quickly (per 0.1 seconds): Low battery power.
Blue flashes slowly (per 1.5 seconds): Firmware upgrade.
HOME Button
Short press to power on the device.
Short press to return to the home screen.
Long press for 1 second to recenter the screen.
TRIGGER Button
Confirm and shoot, etc.
Its functions vary in different games and applications.
APP/BACK Button
Short press to return or go to Menu.
VOLUME Button
Short press to adjust the volume.
Long press to adjust continuously.
Trackpad
Press and hold to confirm.
Touch and slide to turn page.

06
EN
1. Move the Pointer
Swing the controller to move the projection lines of the virtual controller in the field of vision.
2. Confirm, Turn Page
Press any area of the trackpad to confirm. Swipe the trackpad from top to bottom or left
to right to turn page.
3. Confirm/Shoot
Short press the TRIGGER button to confirm/shoot. Its functions vary in different games and
applications.
4. Back/Menu
Short press the APP button to return/go to Menu.
5. Screen Re-centering and Virtual Controller Centering
Look straight ahead with the headset on, point the controller horizontally right in front of
yourself, and press the controller's HOME button for more than 1 second to re-center the
screen. Drag the Menu to the facing position in the current field of vision and center the
projection lines of the virtual controller.
6. Controller Volume Adjustment
Pressing the VOLUME button on the controller can increase or decrease the volume. Long
pressing it can adjust the volume continuously.
7. Changing Dominant Hand
Go to "Settings" ► "Controller" ► "Dominant Hand".
8. Connect to a new controller under Controller Operating Mode (The headset can
only be connected to a maximum of one controller)
Unbind the current controller in "Settings" ► "Controller". Then, short press the HOME
button of the new controller or the HOME button + TRIGGER button + trackpad of the
current controller for 10 seconds. Afterward, follow the instructions on the headset screen.
9. Power off the Controller
You do not need to power off the controller manually. It will power off automatically to
save power in the following situations.
·When the headset is in Deep Sleep mode (1 minute after taking off the headset)
·When the headset's Bluetooth is turned off
·When the controller is unbound in the headset's Controller Management interface
·When the headset is powered off
10. Reset and Restart the Controller Hardware
If the controller does not respond when the HOME button and any button is pressed, or
when the virtual controller in the headset gets stuck and does not move, please pull out
and insert the battery again to restart.
Product Care
This VR headset features replaceable face cushion and straps. The face cushion and straps
are available to purchase separately. Please contact customer service, or a PICO
authorized service provider or your Sales Representative.
Headset (except the lens, face cushion), controller and accessories care
Please use disinfectant wipe (alcohol-based ingredients allowed) or use a microfiber dry
cloth to dip in a small amount of 75% alcohol and gently wipe the surface of the product
until the surface is wet and wait at least 5 minutes, then dry the surface with a microfiber dry cloth.
Note: Please avoid water into the product when cleaning.
During use or storage, please pay attention to avoid hard objects touching the lens to
avoid lens scratches.
Use an optical lens micro-fiber cloth to dip in a little water or use a non-alcoholic
disinfectant wipes to clean the lenses. (Do not wipe the lenses with alcohol or other
harsh or abrasive cleaning solutions as this may lead to damage.)
Lens care
Face cushion care
Use a sterile wipes (alcohol-based ingredients allowed) or a microfiber dry cloth dipped in
a small amount of 75% alcohol to gently wipe the surface and surrounding areas in contact
with the skin until the surface is slightly wet and hold for at least five minutes. Then leave
to dry before use. (Do not expose directly in sunlight.)
Note: The face cushion will have the following effects after repeated cleaning and disinfection.
Moreover, hand washing or machine washing is not recommended, as this will accelerate
the occurrence of the following phenomena. Please change a new face cushion if any of
the following occur:
·
·
Leather ( PU ) face cushion : color change, sticky surface hair, decreased facial comfort
of face.
Regulatory
After powering on the headset, you can go to “Settings”►“General”►“About"►“Regulatory”
on the home page to view the certified supervision product information specific to your
region.
Safety Warnings
Please read the following warnings and information carefully before using the VR Headset
and follow all guidelines on safety and operation.
Failure to follow these guidelines may result in physical injuries (including electric shock,
fire, and other injuries), property damage, and even death. If you allow others to use this
product, you shall be responsible for ensuring that every user understands and follows
all safety and operational instructions.
Ensure that this product is used in a safe environment. By using this product to view an
immersive virtual reality environment, users will not be able to see their physical environment.
Move only within the safe area that you set: keep your surroundings in mind. Do not use
near stairs, windows, heat sources, or other hazardous areas.
Only use if you are in good health. Consult a doctor before use if you are pregnant, elderly,
or have serious physical, mental, visual, or heart problems.
A small number of people may experience epilepsy, fainting, severe dizziness, and other
symptoms caused by flashes and images, even if they have no such medical history.
Consult a doctor before using if you have a similar medical history or have ever
experienced any of the symptoms listed above.
Some people may experience severe dizziness, vomiting, palpitations and even fainting
when using VR Headsets, playing ordinary video games, and watching 3D movies. Consult
a doctor if you have experienced any of the symptoms listed above.
This product is not recommended for children aged 12 and under. It is recommended to
keep headsets, controllers and accessories out of the reach of children. Teenagers
aged 13 and over must use it under adult supervision to avoid accidents.
Some people may be allergic to plastic, PU, fabric, and other materials used in this product.
Long-term contact with skin may result in symptoms such as red-ness, swelling, and
inflammation. Stop using the product and consult a doctor if you experience any of the
symptoms listed above.
This product is not meant for extended use over 30 minutes at a time with rest periods
of at least 10 minutes between uses. Adjust resting and usage periods if you experience
any discomfort.
If you have a big difference in binocular vision, or a high degree of myopia, or astigmatism
or far-sightedness, it is suggested that you wear glasses to correct your eyesight when
using VR headset.
Stop using the product immediately if you experience visual abnormalities (diplopia and
sight distortion, eye discomfort or pain, etc.), excessive sweating, nausea, vertigo,
palpitations, disorientation, loss of balance, etc or other signs of distress.
This product provides access to immersive virtual reality experiences some types of
content may cause discomfort. Stop using immediately and consult a doctor if the
following symptoms occur.
Health and Safety Warnings
Electronic Devices
Do not use this product in locations where the use of wireless devices is explicitly prohibited, as
this may interfere with other electronic devices or cause other hazards.
Please comply with the expressly stated prohibition of the use of wireless equipment in
medical and healthcare facilities, and shut down the equipment and its accessories.
Radio waves generated by this product and its accessories may affect the normal operation
of implantable medical devices or personal medical devices, such as pacemakers, cochlear
implants, hearing aids, etc. Please consult the medical device manufacturer about the
restrictions on the use of this product if you use these medical devices.
Keep a distance of at least 15cm from the implanted medical devices (such as pacemakers,
cochlear implants, etc.) when this product and any accessories are connected. Stop
using the headset and/or its accessories if you observe a persistent interference with
your medical device.
Impact on Medical Devices
Do not use the equipment in dusty, humid, dirty environments, or near strong magnetic
fields, in order to internal circuit failure of this product.
Do not use this equipment during thunderstorms. Thunderstorms may cause product
failure and increases the risk of electric shock.
Operating Temperature: 0-35 ℃ / 32-104 ℉ , minimum humidity 5%, maximum humidity
95% RH ( non-condensing). Non-Operation (Storage): -20-45℃ / -4-113℉ , 85% RH.
Altitude not higher than 2000m (air pressure not less than 80kPa).
Protect your lenses from light. Keep the product away from direct sunlight or ultraviolet
rays, such as windowsills automobile dashboards, or other strong light sources.
Keep the product and its accessories away from rain or moisture.
Do not place the product near heat sources or exposed flames, such as electric heaters,
microwave ovens, water heaters, stoves, candles or t her places that may generate high
temperatures.
Do not apply excessive pressure to the product during storage or when in use to avoid
damage to the equipment and lenses.
Do not use strong chemicals, cleaning agents, or detergents to clean the product or its
accessories, which may cause material changes that affect eye and skin health of the
health. Please follow the instructions in “Product Care” to manage the equipment.
Do not allow children or pets to bite or swallow the product or its accessories.
Operating Environment
Children's Health
Requirements for accessories
CHOKING HAZARD: This product may contain small parts. Please place these out of the
reach of children or pets and do not leave small children or pets with this product
unattended. Children or pets may inadvertently damage the product, swallow small
parts, or get entangled with the cable resulting in suffocation or other hazards.
Only accessories approved by the product manufacturer, such as power supplies and
data cables, can be used with the product.
The use of unapproved third-party accessories may cause fire, explosion or other damages.
The use of unapproved third-party accessories may violate the warranty terms of the
product and the relevant regulations of the country where the product is located. For
approved accessories, please contact PICO Customer Service Center.
Do not operate a motor vehicle, operate machinery, or engage in activities that may have
potentially serious consequences until you have fully recovered from these symptoms.
Epilepsy seizures, loss of consciousness, convulsions, involuntary movements,
dizziness, disorientation, nausea, somnolence, or fatigue.
Eye pain or discomfort, eye fatigue, eye twitching, or visual abnormalities (such as
illusion, blurred vision, or diplopia).
Itchy skin, eczema, swelling, irritation or other discomforts.
Excessive sweating, loss of balance, impaired hand-eye coordination, or other similar
motion sickness symptoms.
-
-
-
-

07
EN
1. Move the Pointer
Swing the controller to move the projection lines of the virtual controller in the field of vision.
2. Confirm, Turn Page
Press any area of the trackpad to confirm. Swipe the trackpad from top to bottom or left
to right to turn page.
3. Confirm/Shoot
Short press the TRIGGER button to confirm/shoot. Its functions vary in different games and
applications.
4. Back/Menu
Short press the APP button to return/go to Menu.
5. Screen Re-centering and Virtual Controller Centering
Look straight ahead with the headset on, point the controller horizontally right in front of
yourself, and press the controller's HOME button for more than 1 second to re-center the
screen. Drag the Menu to the facing position in the current field of vision and center the
projection lines of the virtual controller.
6. Controller Volume Adjustment
Pressing the VOLUME button on the controller can increase or decrease the volume. Long
pressing it can adjust the volume continuously.
7. Changing Dominant Hand
Go to "Settings" ► "Controller" ► "Dominant Hand".
8. Connect to a new controller under Controller Operating Mode (The headset can
only be connected to a maximum of one controller)
Unbind the current controller in "Settings" ► "Controller". Then, short press the HOME
button of the new controller or the HOME button + TRIGGER button + trackpad of the
current controller for 10 seconds. Afterward, follow the instructions on the headset screen.
9. Power off the Controller
You do not need to power off the controller manually. It will power off automatically to
save power in the following situations.
·When the headset is in Deep Sleep mode (1 minute after taking off the headset)
·When the headset's Bluetooth is turned off
·When the controller is unbound in the headset's Controller Management interface
·When the headset is powered off
10. Reset and Restart the Controller Hardware
If the controller does not respond when the HOME button and any button is pressed, or
when the virtual controller in the headset gets stuck and does not move, please pull out
and insert the battery again to restart.
Product Care
This VR headset features replaceable face cushion and straps. The face cushion and straps
are available to purchase separately. Please contact customer service, or a PICO
authorized service provider or your Sales Representative.
Headset (except the lens, face cushion), controller and accessories care
Please use disinfectant wipe (alcohol-based ingredients allowed) or use a microfiber dry
cloth to dip in a small amount of 75% alcohol and gently wipe the surface of the product
until the surface is wet and wait at least 5 minutes, then dry the surface with a microfiber dry cloth.
Note: Please avoid water into the product when cleaning.
During use or storage, please pay attention to avoid hard objects touching the lens to
avoid lens scratches.
Use an optical lens micro-fiber cloth to dip in a little water or use a non-alcoholic
disinfectant wipes to clean the lenses. (Do not wipe the lenses with alcohol or other
harsh or abrasive cleaning solutions as this may lead to damage.)
Lens care
Face cushion care
Use a sterile wipes (alcohol-based ingredients allowed) or a microfiber dry cloth dipped in
a small amount of 75% alcohol to gently wipe the surface and surrounding areas in contact
with the skin until the surface is slightly wet and hold for at least five minutes. Then leave
to dry before use. (Do not expose directly in sunlight.)
Note: The face cushion will have the following effects after repeated cleaning and disinfection.
Moreover, hand washing or machine washing is not recommended, as this will accelerate
the occurrence of the following phenomena. Please change a new face cushion if any of
the following occur:
·
·
Leather ( PU ) face cushion : color change, sticky surface hair, decreased facial comfort
of face.
Regulatory
After powering on the headset, you can go to “Settings”►“General”►“About"►“Regulatory”
on the home page to view the certified supervision product information specific to your
region.
Safety Warnings
Please read the following warnings and information carefully before using the VR Headset
and follow all guidelines on safety and operation.
Failure to follow these guidelines may result in physical injuries (including electric shock,
fire, and other injuries), property damage, and even death. If you allow others to use this
product, you shall be responsible for ensuring that every user understands and follows
all safety and operational instructions.
Ensure that this product is used in a safe environment. By using this product to view an
immersive virtual reality environment, users will not be able to see their physical environment.
Move only within the safe area that you set: keep your surroundings in mind. Do not use
near stairs, windows, heat sources, or other hazardous areas.
Only use if you are in good health. Consult a doctor before use if you are pregnant, elderly,
or have serious physical, mental, visual, or heart problems.
A small number of people may experience epilepsy, fainting, severe dizziness, and other
symptoms caused by flashes and images, even if they have no such medical history.
Consult a doctor before using if you have a similar medical history or have ever
experienced any of the symptoms listed above.
Some people may experience severe dizziness, vomiting, palpitations and even fainting
when using VR Headsets, playing ordinary video games, and watching 3D movies. Consult
a doctor if you have experienced any of the symptoms listed above.
This product is not recommended for children aged 12 and under. It is recommended to
keep headsets, controllers and accessories out of the reach of children. Teenagers
aged 13 and over must use it under adult supervision to avoid accidents.
Some people may be allergic to plastic, PU, fabric, and other materials used in this product.
Long-term contact with skin may result in symptoms such as red-ness, swelling, and
inflammation. Stop using the product and consult a doctor if you experience any of the
symptoms listed above.
This product is not meant for extended use over 30 minutes at a time with rest periods
of at least 10 minutes between uses. Adjust resting and usage periods if you experience
any discomfort.
If you have a big difference in binocular vision, or a high degree of myopia, or astigmatism
or far-sightedness, it is suggested that you wear glasses to correct your eyesight when
using VR headset.
Stop using the product immediately if you experience visual abnormalities (diplopia and
sight distortion, eye discomfort or pain, etc.), excessive sweating, nausea, vertigo,
palpitations, disorientation, loss of balance, etc or other signs of distress.
This product provides access to immersive virtual reality experiences some types of
content may cause discomfort. Stop using immediately and consult a doctor if the
following symptoms occur.
Health and Safety Warnings
Electronic Devices
Do not use this product in locations where the use of wireless devices is explicitly prohibited, as
this may interfere with other electronic devices or cause other hazards.
Please comply with the expressly stated prohibition of the use of wireless equipment in
medical and healthcare facilities, and shut down the equipment and its accessories.
Radio waves generated by this product and its accessories may affect the normal operation
of implantable medical devices or personal medical devices, such as pacemakers, cochlear
implants, hearing aids, etc. Please consult the medical device manufacturer about the
restrictions on the use of this product if you use these medical devices.
Keep a distance of at least 15cm from the implanted medical devices (such as pacemakers,
cochlear implants, etc.) when this product and any accessories are connected. Stop
using the headset and/or its accessories if you observe a persistent interference with
your medical device.
Impact on Medical Devices
Do not use the equipment in dusty, humid, dirty environments, or near strong magnetic
fields, in order to internal circuit failure of this product.
Do not use this equipment during thunderstorms. Thunderstorms may cause product
failure and increases the risk of electric shock.
Operating Temperature: 0-35 ℃ / 32-104 ℉ , minimum humidity 5%, maximum humidity
95% RH ( non-condensing). Non-Operation (Storage): -20-45℃ / -4-113℉ , 85% RH.
Altitude not higher than 2000m (air pressure not less than 80kPa).
Protect your lenses from light. Keep the product away from direct sunlight or ultraviolet
rays, such as windowsills automobile dashboards, or other strong light sources.
Keep the product and its accessories away from rain or moisture.
Do not place the product near heat sources or exposed flames, such as electric heaters,
microwave ovens, water heaters, stoves, candles or t her places that may generate high
temperatures.
Do not apply excessive pressure to the product during storage or when in use to avoid
damage to the equipment and lenses.
Do not use strong chemicals, cleaning agents, or detergents to clean the product or its
accessories, which may cause material changes that affect eye and skin health of the
health. Please follow the instructions in “Product Care” to manage the equipment.
Do not allow children or pets to bite or swallow the product or its accessories.
Operating Environment
Children's Health
Requirements for accessories
CHOKING HAZARD: This product may contain small parts. Please place these out of the
reach of children or pets and do not leave small children or pets with this product
unattended. Children or pets may inadvertently damage the product, swallow small
parts, or get entangled with the cable resulting in suffocation or other hazards.
Only accessories approved by the product manufacturer, such as power supplies and
data cables, can be used with the product.
The use of unapproved third-party accessories may cause fire, explosion or other damages.
The use of unapproved third-party accessories may violate the warranty terms of the
product and the relevant regulations of the country where the product is located. For
approved accessories, please contact PICO Customer Service Center.
Do not operate a motor vehicle, operate machinery, or engage in activities that may have
potentially serious consequences until you have fully recovered from these symptoms.
Epilepsy seizures, loss of consciousness, convulsions, involuntary movements,
dizziness, disorientation, nausea, somnolence, or fatigue.
Eye pain or discomfort, eye fatigue, eye twitching, or visual abnormalities (such as
illusion, blurred vision, or diplopia).
Itchy skin, eczema, swelling, irritation or other discomforts.
Excessive sweating, loss of balance, impaired hand-eye coordination, or other similar
motion sickness symptoms.
-
-
-
-

08
EN
Dispose of your headset and/or accessories in accordance with local regulations and
government advice. Do not dispose of the headset or accessories in the fire or
incinerator, as the battery may explode when overheated. Dispose separately from
household waste.
Please comply with the local laws and regulations on the disposal of the batteries and
the headset as an electronic device, at designated waste collection points and
separately from household waste.
Do not use high volume for extended periods of time to prevent possible hearing damage.
When using headphones, use the minimum volume required to avoid hearing
damage. Prolonged exposure to high volume may cause permanent hearing damage.
Do not use the equipment near fuel stations or hazardous areas containing flammable
articles and chemical agents. Follow all graphic or text instructions when in possession of
the product around these areas. Operating the product in these hazardous sites poses
risk of explosion or fire.
Do not store or transport the product or its accessories in the same container as flammable
liquids, gases, or substances.
Do not use the product when walking, cycling, driving, or situations that require full visibility.
Take caution if using the product as a passenger in a motor vehicle, as irregular movement
may increase the risk of motion sickness.
Environmental protection
Hearing protection
Flammable and explosive areas
Transportation safety
Charger safety
Battery safety
Only charging devices provided in the product package or specified as an approved device
by the manufacturer should be used.
When charging is completed, disconnect the charger from the equipment and unplug the
charger from the power outlet.
Do not operate the equipment, charger or cable with wet hands to avoid short circuits,
failure, or electric shock.
Do not use the charger if wet.
If the charging adapter or cable is damaged, discontinue using to prevent the risk of
electric shock or fire.
VR Headsets are equipped with non-removable internal batteries. Do not attempt to
replace the battery, as doing so may cause battery damage,fire, or human injury. The
battery can only be replaced by PICO or PICO authorized service providers.
Do not disassemble or modify the battery, insert foreign objects, or immerse in water
or other liquid. Handling the battery as such can cause chemical leakage, overheating,
fire, or explosion. If the battery appears to be leaking material, avoid contact with skin
or eyes.In case of material contact with skin or eyes, immediately rinse with clear water
and seek medical advice.
Do not drop, squeeze ,or puncture the battery. Avoid subjecting the battery to high
temperatures or external pressure, which may result in corruption and overheating of
the battery.
Do not connect the metal conductor with the two poles of the battery, or contact the
terminal of the battery, so as to avoid short circuit of the battery and physical injury
such as burns caused by overheating of the battery.
Please contact PICO or PICO authorized service providers to replace the battery when
the standby time of your device is obviously shorter than the normal time. Replacement
of a battery with an incorrect type may defeat a safeguard.
Do not use your product if any part is broken or damaged.
Do not attempt to repair any part if your product yourself. Repairs should only be made
by an PICO authorized servicer.
Do not expose your headset and controllers to moisture, high humidity, high concentrations
of dust or airborne materials, temperatures outside their operating range or direct
sunlight to avoid damage.
Keep your headset, controllers, charger, cables and accessories away from pets to
avoid damage.
VR Headset
VR Product Care
No Direction Sunlight on Lense
Controller
Disposal and recycling information
The crossed-out wheeled bin symbol on your product, battery, the literature or
packaging reminds you that all electronic products and batteries must be taken to
separate waste collection points at the end of their working lives; they must not be
disposed of in the normal waste stream with household garbage. It is the responsibility
of the user to dispose of the equipment using a designated collection point or
service for separate recycling of waste electrical and electronic equipment (WEEE) and
batteries according to local laws. Proper collection and recycling of your equipment helps
ensure electrical and electronic equipment (EEE) waste is recycled in a manner that
conserves valuable materials and protects human health and the environment, improper
handling, accidental breakage, damage, and/or improper recycling at the end of its life
may be harmful to health and environment. For more information about where and how
to drop off your EEE waste, please contact your local authorities, retailer or household
waste disposal service or visit the website https:// www.picoxr.com
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limifts are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to o perate the equipment.
FCC RF radiation exposure statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
US Regulatory Information
“Supplier’s Declaration of Conformity 47 CFR §2.1077 Compliance Information” SDoC
Website: https://www.picoxr.com/legal/compliance
Canada Regulatory Information
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the
following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Caution:
PICO Product Limited Warranty
PLEASE READ THIS LIMITED WARRANTY CAREFULLY TO UNDERSTAND YOUR RIGHTS AND
OBLIGATIONS. BY USING YOUR PICO PRODUCT OR ACCESSORY, YOU AGREE TO THE
LIMITED WARRANTY.
PICO issues this warranty to you, as a consumer who has purchased a new, covered product
from PICO or an authorized retailer (“you”). This warranty is not available to products that
were purchased from any source other than PICO or an authorized retailer.
What Does This Warranty Do?
This Warranty gives you specific legal rights, and you may also have other rights which vary
from country to country. This Warranty is in addition to and does not affect any rights you
have under the laws in your jurisdiction concerning the sale of consumer goods.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
The high-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference
and/or damage to LE-LAN devices.
DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz,
5470-5600 MHz, and 5650-5725 MHz.
The exposure standard for wireless transmitter employs a unit of measurement known as
the Specific Absorption Rate, or SAR. The SAR limit set by the IC is 1.6W/kg.
The highest SAR value for the EUT as reported to the IC when tested for use is1.55 W/kg.
This equipment may be operated in
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into on outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation. Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

09
EN
Dispose of your headset and/or accessories in accordance with local regulations and
government advice. Do not dispose of the headset or accessories in the fire or
incinerator, as the battery may explode when overheated. Dispose separately from
household waste.
Please comply with the local laws and regulations on the disposal of the batteries and
the headset as an electronic device, at designated waste collection points and
separately from household waste.
Do not use high volume for extended periods of time to prevent possible hearing damage.
When using headphones, use the minimum volume required to avoid hearing
damage. Prolonged exposure to high volume may cause permanent hearing damage.
Do not use the equipment near fuel stations or hazardous areas containing flammable
articles and chemical agents. Follow all graphic or text instructions when in possession of
the product around these areas. Operating the product in these hazardous sites poses
risk of explosion or fire.
Do not store or transport the product or its accessories in the same container as flammable
liquids, gases, or substances.
Do not use the product when walking, cycling, driving, or situations that require full visibility.
Take caution if using the product as a passenger in a motor vehicle, as irregular movement
may increase the risk of motion sickness.
Environmental protection
Hearing protection
Flammable and explosive areas
Transportation safety
Charger safety
Battery safety
Only charging devices provided in the product package or specified as an approved device
by the manufacturer should be used.
When charging is completed, disconnect the charger from the equipment and unplug the
charger from the power outlet.
Do not operate the equipment, charger or cable with wet hands to avoid short circuits,
failure, or electric shock.
Do not use the charger if wet.
If the charging adapter or cable is damaged, discontinue using to prevent the risk of
electric shock or fire.
VR Headsets are equipped with non-removable internal batteries. Do not attempt to
replace the battery, as doing so may cause battery damage,fire, or human injury. The
battery can only be replaced by PICO or PICO authorized service providers.
Do not disassemble or modify the battery, insert foreign objects, or immerse in water
or other liquid. Handling the battery as such can cause chemical leakage, overheating,
fire, or explosion. If the battery appears to be leaking material, avoid contact with skin
or eyes.In case of material contact with skin or eyes, immediately rinse with clear water
and seek medical advice.
Do not drop, squeeze ,or puncture the battery. Avoid subjecting the battery to high
temperatures or external pressure, which may result in corruption and overheating of
the battery.
Do not connect the metal conductor with the two poles of the battery, or contact the
terminal of the battery, so as to avoid short circuit of the battery and physical injury
such as burns caused by overheating of the battery.
Please contact PICO or PICO authorized service providers to replace the battery when
the standby time of your device is obviously shorter than the normal time. Replacement
of a battery with an incorrect type may defeat a safeguard.
Do not use your product if any part is broken or damaged.
Do not attempt to repair any part if your product yourself. Repairs should only be made
by an PICO authorized servicer.
Do not expose your headset and controllers to moisture, high humidity, high concentrations
of dust or airborne materials, temperatures outside their operating range or direct
sunlight to avoid damage.
Keep your headset, controllers, charger, cables and accessories away from pets to
avoid damage.
VR Headset
VR Product Care
No Direction Sunlight on Lense
Controller
Disposal and recycling information
The crossed-out wheeled bin symbol on your product, battery, the literature or
packaging reminds you that all electronic products and batteries must be taken to
separate waste collection points at the end of their working lives; they must not be
disposed of in the normal waste stream with household garbage. It is the responsibility
of the user to dispose of the equipment using a designated collection point or
service for separate recycling of waste electrical and electronic equipment (WEEE) and
batteries according to local laws. Proper collection and recycling of your equipment helps
ensure electrical and electronic equipment (EEE) waste is recycled in a manner that
conserves valuable materials and protects human health and the environment, improper
handling, accidental breakage, damage, and/or improper recycling at the end of its life
may be harmful to health and environment. For more information about where and how
to drop off your EEE waste, please contact your local authorities, retailer or household
waste disposal service or visit the website https:// www.picoxr.com
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limifts are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to o perate the equipment.
FCC RF radiation exposure statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
US Regulatory Information
“Supplier’s Declaration of Conformity 47 CFR §2.1077 Compliance Information” SDoC
Website: https://www.picoxr.com/legal/compliance
Canada Regulatory Information
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the
following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
Caution:
PICO Product Limited Warranty
PLEASE READ THIS LIMITED WARRANTY CAREFULLY TO UNDERSTAND YOUR RIGHTS AND
OBLIGATIONS. BY USING YOUR PICO PRODUCT OR ACCESSORY, YOU AGREE TO THE
LIMITED WARRANTY.
PICO issues this warranty to you, as a consumer who has purchased a new, covered product
from PICO or an authorized retailer (“you”). This warranty is not available to products that
were purchased from any source other than PICO or an authorized retailer.
What Does This Warranty Do?
This Warranty gives you specific legal rights, and you may also have other rights which vary
from country to country. This Warranty is in addition to and does not affect any rights you
have under the laws in your jurisdiction concerning the sale of consumer goods.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
The high-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference
and/or damage to LE-LAN devices.
DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350 MHz,
5470-5600 MHz, and 5650-5725 MHz.
The exposure standard for wireless transmitter employs a unit of measurement known as
the Specific Absorption Rate, or SAR. The SAR limit set by the IC is 1.6W/kg.
The highest SAR value for the EUT as reported to the IC when tested for use is1.55 W/kg.
This equipment may be operated in
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into on outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation. Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

10
EN
How to Obtain Warranty Service?
You can check the user manual or visit https://business.picoxr.com when you meet the problem
during using. If the problem cannot be resolved by reference to the user manual and/or
resources available at https://business.picoxr.com, You should contact the Distributor from
which You purchased the Product or Accessory for assistance.
In the event of a perceived malfunction in the Product or Accessory, You should contact us
and provide the following details and take the following actions:
Governing Law
This Limited Warranty will be governed by the law of the country in which the Product and/or Accessories
were purchased and the relevant courts of that country will have exclusive jurisdiction in
relation to this Limited Warranty. If you live in the UK or EU, you may have additional rights
and can bring legal proceedings in the courts of your country of residence.
Laws and Regulations
Copyright © Qingdao Chuangjian Weilai Technology Co.,Ltd. All Rights Reserved.
This information is for reference only and does not constitute any form of commitment. Products
(including but not limited to color, size, and screen display.) shall be subject to physical
objects.
User Software License Agreement
Before using the product, please read the software license agreement carefully. When
starting to use the product, you agree to be bound by the license agreement
If you do not agree to the terms of this agreement, do not use the product and software.
For more details about the agreement, please visit: https://business.picoxr.com/proto-
col?type=user
Privacy Protection
To learn how we protect your personal information, please visit: https://business.pi-
coxr.com/protocol?type=privacy
Product Name: VR All-In-One Headset | Headset Model: A7Q10 | Controller Model: C1B10
For more information about PICO's products, policy ,and authorized servers, please visit
PICO’s official website: https://business.picoxr.com
Company Name: Qingdao Chuangjian Weilai Technology Co.,Ltd.
Company Address: Room 401, 4th Floor, Building 3, Qingdao Research Institute, 393
Songling Road, Laoshan District, Qingdao City, Shandong Province, P.R.China
For more after-sales information, please visit: https://www.picoxr.com/support/faq
Defects or damage resulting from improper usage, maintenance, not included in this manual;
Screen damage caused by sunlight or UV light exposure or other strong light sources;
Deterioration of the cosmetic appearance of the Product or Accessory due to normal wear and tear;
Consumable parts, such as: AA Battery, Lanyard, Cleaning cloth, Face cushion,
Headband, Earphone hole cap, Mounting kit, Mounting pad and protective coatings that
are reasonably expected to diminish over time, unless failure has occurred due to a
malfunction;
Gifts and packages other than product and accessory;
Damage caused by dismantling, modification and repair without PICO or service
provider authorized by PICO;
Damage caused by force majeure such as fire, flood, and lightning;
The product has exceeded the valid period of the warranty.
-
-
-
-
-
-
-
-
The model and serial number of Product and Accessory;
Your full address and contact information;
A copy of the original invoice, receipt or bill of sale for the purchase of the product. You
must present valid proof of purchase upon making any claims pursuant to this Limited
Warranty.
You should back up all your personal programs or data and delete them from the
product before you return the product to us. We cannot guarantee that we will be able
to repair the Product without risk to or loss of programs or data, and any replacement
Product will not contain any of your data that was stored on the original Product.
We will determine if there is a defect or malfunction covered by this warranty. If we find
a defect or malfunction covered by this warranty, we will repair or replace the Product
to provide the Warranty Functionality, and we will send the repaired Product or a
replacement Product. In the event that the Product cannot be repaired or replaced,
You may be entitled to a refund.
Any repaired or replaced product will continue to be covered by this warranty for the
remainder of the original warranty Period or ninety (90) days following your receipt of
the replacement or repaired product, whichever is greater.
-
-
-
-
-
-
Not Covered by This Warranty
1
安装电池
拇指按压箭头位置同时向下滑动
包装盒内包括：
头盔 / 手柄 / 碱性干电池*2 / USB-C to C 2.0数据线 / 用户指南
使用前注意事项
快速引导
本产品在开阔的室内环境使用体验最佳，建议至少预留2米x2米的空间。使用前请确认身体
没有不适且周围环境安全，特别是佩戴头盔在室内行走移动时，要尽量避免发生意外。
不建议12岁及以下儿童使用本产品，建议将头盔、手柄和配件置于儿童够不到的位置，13
岁及以上青少年须在成人监护下使用，以免发生意外。
本产品无近视调节功能，近视用户请佩戴眼镜使用并尽量避免近视眼镜被头盔的光学镜片
磨伤或刮伤。建议在使用和收纳时注意防护光学镜片，避免尖锐物体划伤镜片，擦拭清洁
时请使用柔软的眼镜布，否则可能划伤镜片，影响视觉效果。
长时间使用可能引发轻微的昡晕或者眼疲劳，建议使用30分钟后适当休息，可通过眼保健
操或观看远处物体缓解眼部疲劳。如果您的身体感到任何不适，请立即停止使用。
当头盔镜片被光照或紫外线照射时(尤其在户外、阳台、窗台及汽车内存放时)，可能导致屏
幕出现永久性黄斑。 请尽量避免该情况发生，此种屏幕损坏不在产品的质保范围内。
建议勿将声音音量调得过大，否则可能对听觉造成损伤。
本产品可通过头盔按键实现基本操作，如需体验更丰富有趣的内容，请连接手柄使用。
本产品支持三段式瞳距调节功能，请根据自身瞳距选择相近档位。默认中间瞳距可兼容大
部分人群，建议视觉有重影或对眼的人调整至自己合适的瞳距体验。使用不合适的瞳距档
位，可能会引起重影或者眼睛疲劳。

11
CN
How to Obtain Warranty Service?
You can check the user manual or visit https://business.picoxr.com when you meet the problem
during using. If the problem cannot be resolved by reference to the user manual and/or
resources available at https://business.picoxr.com, You should contact the Distributor from
which You purchased the Product or Accessory for assistance.
In the event of a perceived malfunction in the Product or Accessory, You should contact us
and provide the following details and take the following actions:
Governing Law
This Limited Warranty will be governed by the law of the country in which the Product and/or Accessories
were purchased and the relevant courts of that country will have exclusive jurisdiction in
relation to this Limited Warranty. If you live in the UK or EU, you may have additional rights
and can bring legal proceedings in the courts of your country of residence.
Laws and Regulations
Copyright © Qingdao Chuangjian Weilai Technology Co.,Ltd. All Rights Reserved.
This information is for reference only and does not constitute any form of commitment. Products
(including but not limited to color, size, and screen display.) shall be subject to physical
objects.
User Software License Agreement
Before using the product, please read the software license agreement carefully. When
starting to use the product, you agree to be bound by the license agreement
If you do not agree to the terms of this agreement, do not use the product and software.
For more details about the agreement, please visit: https://business.picoxr.com/proto-
col?type=user
Privacy Protection
To learn how we protect your personal information, please visit: https://business.pi-
coxr.com/protocol?type=privacy
Product Name: VR All-In-One Headset | Headset Model: A7Q10 | Controller Model: C1B10
For more information about PICO's products, policy ,and authorized servers, please visit
PICO’s official website: https://business.picoxr.com
Company Name: Qingdao Chuangjian Weilai Technology Co.,Ltd.
Company Address: Room 401, 4th Floor, Building 3, Qingdao Research Institute, 393
Songling Road, Laoshan District, Qingdao City, Shandong Province, P.R.China
For more after-sales information, please visit: https://www.picoxr.com/support/faq
Defects or damage resulting from improper usage, maintenance, not included in this manual;
Screen damage caused by sunlight or UV light exposure or other strong light sources;
Deterioration of the cosmetic appearance of the Product or Accessory due to normal wear and tear;
Consumable parts, such as: AA Battery, Lanyard, Cleaning cloth, Face cushion,
Headband, Earphone hole cap, Mounting kit, Mounting pad and protective coatings that
are reasonably expected to diminish over time, unless failure has occurred due to a
malfunction;
Gifts and packages other than product and accessory;
Damage caused by dismantling, modification and repair without PICO or service
provider authorized by PICO;
Damage caused by force majeure such as fire, flood, and lightning;
The product has exceeded the valid period of the warranty.
-
-
-
-
-
-
-
-
The model and serial number of Product and Accessory;
Your full address and contact information;
A copy of the original invoice, receipt or bill of sale for the purchase of the product. You
must present valid proof of purchase upon making any claims pursuant to this Limited
Warranty.
You should back up all your personal programs or data and delete them from the
product before you return the product to us. We cannot guarantee that we will be able
to repair the Product without risk to or loss of programs or data, and any replacement
Product will not contain any of your data that was stored on the original Product.
We will determine if there is a defect or malfunction covered by this warranty. If we find
a defect or malfunction covered by this warranty, we will repair or replace the Product
to provide the Warranty Functionality, and we will send the repaired Product or a
replacement Product. In the event that the Product cannot be repaired or replaced,
You may be entitled to a refund.
Any repaired or replaced product will continue to be covered by this warranty for the
remainder of the original warranty Period or ninety (90) days following your receipt of
the replacement or repaired product, whichever is greater.
-
-
-
-
-
-
Not Covered by This Warranty
1
安装电池
拇指按压箭头位置同时向下滑动
包装盒内包括：
头盔 / 手柄 / 碱性干电池*2 / USB-C to
C 2.0数据线 / 用户指南
使用前注意事项
快速引导
本产品在开阔的室内环境使用体验最佳，建议至少预留2米x2米的空间。使用前请确认身体
没有不适且周围环境安全，特别是佩戴头盔在室内行走移动时，要尽量避免发生意外。
不建议12岁及以下儿童使用本产品，建议将头盔、手柄和配件置于儿童够不到的位置，13
岁及以上青少年须在成人监护下使用，以免发生意外。
本产品无近视调节功能，近视用户请佩戴眼镜使用并尽量避免近视眼镜被头盔的光学镜片
磨伤或刮伤。建议在使用和收纳时注意防护光学镜片，避免尖锐物体划伤镜片，擦拭清洁
时请使用柔软的眼镜布，否则可能划伤镜片，影响视觉效果。
长时间使用可能引发轻微的昡晕或者眼疲劳，建议使用30分钟后适当休息，可通过眼保健
操或观看远处物体缓解眼部疲劳。如果您的身体感到任何不适，请立即停止使用。
当头盔镜片被光照或紫外线照射时(尤其在户外、阳台、窗台及汽车内存放时)，可能导致屏
幕出现永久性黄斑。 请尽量避免该情况发生，此种屏幕损坏不在产品的质保范围内。
建议勿将声音音量调得过大，否则可能对听觉造成损伤。
本产品可通过头盔按键实现基本操作，如需体验更丰富有趣的内容，请连接手柄使用。
本产品支持三段式瞳距调节功能，请根据自身瞳距选择相近档位。默认中间瞳距可兼容大
部分人群，建议视觉有重影或对眼的人调整至自己合适的瞳距体验。使用不合适的瞳距档
位，可能会引起重影或者眼睛疲劳。
A

12
CN
4
将头盔罩住面部或者眼镜
向下推动后脑垫使其套在头上
佩戴头盔
提示：近视用户请佩戴眼镜使用，本产品不具备近视调节功能
5
调节至清晰舒坦的位置
微调绑带长度及佩戴位置至视野清晰
本产品支持三段式瞳距(58mm/63.5mm/69mm)调节功能，默认中间瞳距可兼容大部分人
群，建议视觉有重影或对眼的人调整至自己瞳距相近的档位体验。
调节时请正视头盔镜片，双手持镜筒中间偏上部位使左右镜简同时向里或者向外运动。按照
下图所示，以右镜筒为例，镜筒上方刻度与白色竖线符号的相对关系向左或者向右拨动镜片
调节档位
(镜筒刻度与白色竖线对齐: 63.5mm,镜筒刻度在白色竖线偏左: 58mm,镜筒刻度在白色竖线
偏右：69mm）。
瞳距调节
提示：使用不合适的瞳距档位，可能会引起重影或者眼镜疲劳
近视用户佩戴
本设备不具备近视调节功能，头盔可支持佩戴镜框宽度小于160mm的大多数标准眼镜。

13
CN
4
将头盔罩住面部或者眼镜
向下推动后脑垫使其套在头上
佩戴头盔
提示：近视用户请佩戴眼镜使用，本产品不具备近视调节功能
5
调节至清晰舒坦的位置
微调绑带长度及佩戴位置至视野清晰
本产品支持三段式瞳距(58mm/63.5mm/69mm)调节功能，默认中间瞳距可兼容大部分人
群，建议视觉有重影或对眼的人调整至自己瞳距相近的档位体验。
调节时请正视头盔镜片，双手持镜筒中间偏上部位使左右镜简同时向里或者向外运动。按照
下图所示，以右镜筒为例，镜筒上方刻度与白色竖线符号的相对关系向左或者向右拨动镜片
调节档位
(镜筒刻度与白色竖线对齐: 63.5mm,镜筒刻度在白色竖线偏左: 58mm,镜筒刻度在白色竖线
偏右：69mm）。
瞳距调节
提示：使用不合适的瞳距档位，可能会引起重影或者眼镜疲劳
近视用户佩戴
本设备不具备近视调节功能，头盔可支持佩戴镜框宽度小于160mm的大多数标准眼镜。

14
CN

15
CN

16
CN

17
CN

18
CN
セット内容
VRヘッドセット / コントローラー / アルカリ電池 2個 / USB-C to C 2.0データケーブル / ユーザー
ガイド
健康および安全に関する重要な注意事項
•
本製品は広い室内でご使用ください。本デバイスをご使用の際は、最低でも2m×2mのス
ペースを確保することをお勧めします。ご使用前に、体調に問題がないことと、周囲の環
境が安全であることを確認してください。事故を防ぐため、ヘッドセットの着用時に室内
を移動する際は十分にご注意ください。
12歳以下のお子様による本製品の使用は推奨されていません。VRヘッドセット、コント
ローラー、およびアクセサリーはお子様の手の届かないところに保管することをお勧めし
ます。事故を防ぐため、13歳以上の未成年者の方は成人の監督下で使用してください。
本製品には近視調整機能がありません。近視のユーザーは眼鏡を着用したままヘッドセッ
トを装着してください。その際、お使いの眼鏡がヘッドセッドの光学レンズをこすったり
傷つけたりすることがないようご注意ください。ヘッドセットのご使用中や保管時は光学
レンズを保護してください。レンズを傷つける恐れのある鋭利なものは避けてください。
レンズは柔らかいマイクロファイバーの布でクリーニングし、傷がつかないようにしてく
ださい。レンズに傷がつくと、映像体験に悪影響が及びます。
長時間のご使用は、めまいや眼精疲労の原因となります。ご使用時は30分ごとに休憩して
ください。目の運動をしたり、遠くの物体を見たりすることで目の疲れを和らげることが
できます。ご使用中に不快感を覚えた場合は、直ちに製品の使用を中止してください。
ヘッドセッドのレンズを直射日光や紫外線にさらすと（特に屋外、ベランダ、窓台、自動
車内での保管時）、画面に黄色い斑点状の変色が起き、修復できなくなる可能性がありま
す。このような状況下で生じた画面の損傷は製品保証の対象外ですので、十分にご注意く
ださい。
音量を上げすぎないでください。聴力に悪い影響を与える可能性があります。
ヘッドセットのボタンを押すことで、本製品の基本操作ができます。コントローラーと接
続することで、より豊かで刺激的な体験をお楽しみいただけます。
本製品は、3つのプリセット済み瞳孔間距離（IPD）に対応しています。ご自分のIPDに
合ったレンズ間隔をお選びください。初期設定では中間の間隔になっており、ほとんどの
ユーザーに対応しています。複視や斜視のユーザーは、ご自分のIPDに合ったレンズ間隔
に調整する必要があります。レンズ間隔が合わないまま使用すると、複視や眼精疲労の原
因となります。
•
•
•
•
•
•
•
製品およびパッケージは定期的に更新されており、スタンドアローンヘッドセットの機能およびコンテンツは将来的に
アップグレードされる可能性があります。
そのため、本取扱説明書および製品パッケージに記載されている内容、外観、機能は変更されることがあり、最終製
品が反映されていない場合があります。本書の説明はあくまで参考としてご利用ください。
本ユーザーガイドには重要な安全情報が含まれておりますので、本製品を使用される前によくお読みになり、他の
ユーザーの方々ともこの情報をご共有ください。本ユーザーガイドは、今後の参照用として保管してください。
クイックガイド
電池を取り付ける
矢印の位置を親指で押し、カバー
を下にスライドさせます。
2
ステータス表示が青色に点滅するまでホームボタンを押します。
コントローラーの電源を入れる
ステータス表示が青色に点灯するまで、ヘッドセットの電源ボタンを長押しします。
3
ヘッドセットの電源を入れる
1
*
*
How to Obtain Warranty Service?
You can check the user manual or visit https://business.picoxr.com when you meet the problem
during using. If the problem cannot be resolved by reference to the user manual and/or
resources available at https://business.picoxr.com, You should contact the Distributor from
which You purchased the Product or Accessory for assistance.
In the event of a perceived malfunction in the Product or Accessory, You should contact us
and provide the following details and take the following actions:
Governing Law
This Limited Warranty will be governed by the law of the country in which the Product and/or Accessories
were purchased and the relevant courts of that country will have exclusive jurisdiction in
relation to this Limited Warranty. If you live in the UK or EU, you may have additional rights
and can bring legal proceedings in the courts of your country of residence.
Laws and Regulations
Copyright © Qingdao Chuangjian Weilai Technology Co.,Ltd. All Rights Reserved.
This information is for reference only and does not constitute any form of commitment. Products
(including but not limited to color, size, and screen display.) shall be subject to physical
objects.