Pilot Communications 30cc User manual

www.pilot
www.pilot- -rc.com rc.com
Wingspan:88in
Wingarea: 1479.8spin
Length:78.8in
Engine: 50CC
AssemblyManual For
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

1
INTRODUCTION
Thankyoufor purchasing
our new50cc Yak-54. westrive
toachieve therealQuick
BuildedandARFaircraf .
Itjust requires theleast
amoutofassemblyofanykit
that almost finishedin
factory.To obtaintheperfect
performence,boththedesign
and manufacturing have been
takencarewiththehighest
quality from any
hardware,covering,woodand
glueintheconstructionas
well.Byoptimalweightand
reliableconstruction,youwill
find thisplaneisreallyideal
for 3D-Freestyleand
aerobatic.
Sowehopeeveryeffortand
service weofferwill make you
feeleasy and have awonderful
timeinthepleasureofflying in
3Dspace.
Moreinformationonwebsite
www.pilot
www.pilot- -rc.com rc.com
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

2
W
WARRANTY ARRANTY
■All Pilot-RC productsareguaranteedagainst
defectsfor30daysof receivingyourairplane. This
warrantyislimited toconstruction orproductions
defectsin bothmaterial and workmanship, doesn't
coveranycomponentpartsdamagedbyuseor
modification .
■The manufacturecan'tsupervisethe assembly
,operationandmaintenance,and can'tensureyour
radio systemisingood condition. Therefore,weare
notresponsibleforanydamageoccurring during
theuseofaradio controlledmodel. It isimpossible
todetermine forcertain wehthercrashdamagewas
the result ofaradio systermfailureorpiloterroreven
improperinstallation of ourproducts.Model airplane
ownerisusingiton hisownresponsibility.
■Inno event should Pilot-RC accept the liability
exceedstheoriginal cost of theairframe(notinclude
engine and radiosystem).
■Nomatterwhat reason you wishtoreturnthis
airplane , allshippingcostwill be paid bycostumer.If
somepartsrequirereplacement fromus,theoriginal
parts returnisat costumer'expense.
PDF 件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn

3
ATTENTION
ATTENTION
■You shouldnot regardthisplaneas toy!
■
Toensuresafety,pleaseread the instruction
manual thoroughlybeforeassembly.
■Buildingand operatingmodel plane require
diligentpracticingand correctguidance. Any
neglect,carelessnessand missing experiencecan
causeseriousbodilyharmandpropertydamage.
■Seekthe assistantofaexperiencedpersonor
airplane model clubsin assembly,operation and
maintenancetoensurequickand successfullearning
■Flyonlyinprovenmodel airfield that AMA
(Academyof Model Areonautics)approved
Pilot-RC has theright to changeto thisplane
,instruction and limitedwarrantywithout notice.
Ifyou haveanyproblemsand questions,please
contactpilot RC
Email: [e-mail] , [e-mail]
Cellphone:[phone]
FAX: [phone]
Address: No.34,ChengnanErRoad , Zhongshan city, 528400,Guangdong
Province, China
PDF 件使用 "pdfFactory Pro" 试用版本创建 餀www.fineprint.com.cn

4
Introduction... ...
Warranty... ... .
Attention... ... .
LandingGearAndRudderUnit
RudderAssembly
RudderControlHorns………..…….…...……..
TailWheelInstallation …………..……..........
Landing GearAssembly.
MainLanding GearInstallation ………….…..…….
PantsInstallation…………..….………
ServoUnit
Wing ServoAssembly
ServoArmInstallation ………….….……….
AileronControlHorns………….……….…..
ServoInstallation …….…………..……
RudderServoAssembly
ServoTrayInstallation ….…….….......……..
ServoInstallation ……….….……...……
ElevatorServoAssembly
ServoArmInstallation ………….…………….
ElevatorControlHorns……………....….……
ServoInstallation ……………….....………
SwitchAssembly ………….……….....………
EngineUnit
Engine Assembly……….…..……..……
ThrottleServoAssembly ….….…...…….……
Ignition Module ………….…….……….
HatchAnd FuleTank ………….….……....……
Crowl Assembly …………………......……
CGAndControl Throws …………………………..
FlightPreperation…...…………….….…..……
INDEX
1
2
3
17
18
5
7
9
11
12
13
14
21
22
23
26
27
29
28
30
31
33
34
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

5
Landing Gearand RudderUnit
RudderAssemby
RudderControlHorn 1.Tear off thecover onthehorns
and locking plates
Pleaserefertothe
HARDWARELIST
(download withinstruction)
togetthe exactinformation
abouteverystep. Aprinted
list isrecommended for
your checking rapidlyin
wholeassembly
2. Tracearound the locking plate
withkinfeandcutoff the cover
below.Thenthepre-cutslotsappear
Example:
Onthestep of RudderControlHorninstallation
You cansearch
Rudder
PDF 件使用 "pdfFactory Pro" 试用版本创建 ãwww.fineprint.com.cn

6
RudderAssembly
3. Scuff themiddleof hornswitha
pieceof sand paperfor goodglue
bond.Thenclean upthesurface
4. Applythe 30minutesepoxy
inside the pre-cut slot, andcoat the
horn withepoxyasshown
6. Makesure the horn line upwith
groundandalign thebothside
beforeepoxyhascured
5. Slidthe horn intoslot slightly
Mountthe locking platesin
place.Wipe awayexcessgluewith
rubbingalcohol
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

7
7.Notethepre-drill holefor tail
wheelunderthecover.
8. Tryfit thetailwheelsubassembly
and drill holewith6mm bit .Butdo
not mountthe rudder steering tube
until finishtailwheelinstallation
Tail WheelInstallation
RudderAssembly
1. Drawacenterlinewithapencil
asshown
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

8
2. Mount self-tapping screwson the
tail wheelmounting blockwiththe
bracket taped on place
3. Insert steering armintorudder
steeringtube and ensuretheproper
depth
RudderAssembly
4. Epoxythesteeringtubeinplace
5. Tightenthesetnut asshown
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

9
MainLanding GearInstallation
Landing GearAssembly
NOTE: the correct edge inmounting
Taper
torear
Straight
edge to
frontof
fuse
PDF 件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn

10
Landing GearAssembly
1.Install thelandinggearwiththe
boltsand locking nuts
Note:Don t over tighten and crack
the carbonfiber
2. Install thelanding gearaxleswith
locknut ,but do not tighten 4. Makethe flat sidesofthe axlebolt
verticalwithground .Thentighten the
locknut against the landinggear strut
3. Lift the rear of fusetoline it upwith
groundasshown
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

11
Landing GearAssembly
1. Lift the rear of fuseand linethe
wheelpantup withthegroundby
slippingthemover theaxlesand
supportingthemfromthe rear for the
properclearance
2. Drill the holesfor the mounting
boltsand install the blind nuts.
3. Finishthe wheelpantsmounting
withtheboltsanduseBlue Loctite
on thethreads
5.Install thecollarsand wheelin
orderwith adrop ofBlueLoctite on
the collar set screwand ensurethe
wheelisfreetorotate.
PantsInstallation
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

12
ServoUnit
Wing ServoAssembly
MinimumRequestServo:
ServoArmInstallation
1. Turn onyour transmitterand
plug theservointoreceiver. Ensure
everychannelisneutral
2. Ensure the servoarmis90
degreeswithservoasshown. Then
markand drill holeswith2mm bit
3. Mounting screwsand nuts
180 in.zo/ MetalGear / Digital
Adrop of fast
curedgulehere
PDF 件使用 "pdfFactory Pro" 试用版本创建 ÿwww.fineprint.com.cn

13
AileronControl Horns
1.Tear off thecover onthehorns
and locking plates
2. Tracearound the locking plate
withkinfeandcutoff the cover
below.Thenthepre-cutslotsappear
3. Scuff thehornswithapieceof
sand paperforgood glue bond.Then
clean up thesurface
Wing ServoAssembly
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

14
4. Applythe 30minutesepoxy
inside the pre-cut slot forhorn,and
coat thehorn withepoxyasshown
5. Slidethe hornintoslotslightly
and Mountthelocking platein
place.Wipe awayexcessepoxy
withrubbingalcohol
ServoInstallation
1. Cutoutthe coverfor servolocation
carefullyasshown
Wing ServoAssembly
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

15
3.Tape the lead topull-string
tightly.Inordertoensuretheservo
wirecanbepulledoutwithout
hangingupinsidewing
4. Then put theextention lead
through theroot of wing
5. Install servowithmounting
screws.Facethebrand toward the
trailingedgeofthe wing.Use1mm
bit todrill themounting holes
Wing ServoAssembly
2.Lockthe connector withthe
provided safetyclipagainst vibration
and loosened tensionasshown
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

16
6.Install theservoarmsfacing
towardthewing tipand adjust
pushrod inproper lengthtokeepthe
aileronpanelontheneutralposition
7. Repeatall thestepabovefor the
other wing
The carbontube and wing boltsuse
tobe mountedinthefinalassembly
Wing ServoAssembly
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

17
RudderServoAssembly
ServoTrayInstallation
1.Turn onyourradiodeviceaccording
the Wing ServoInstallation.Keep the
servoholeson centerandthearm
alignedwithservoasshown. Then tape
tightly
2. Drill holeswith2mm bit
Adrop of fast
curedgulehere
3. Mounting screwsand nuts
MinimumRequestServo:
180 in.zo/ MetalGear / Digital
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

18
ServoInstallation
1.Mount servowithmounting
screwsand facethe brandtoward
the rudder.Drill holeswith1mm bit
2. Tape the rudderpaneltotopof
the verticalfininthe neutralposition
tomakeit straight
The rudder cablesand couplershave
been installed asshown
3. Attachthepre-installedboll link
tothe rudder hornandnottighten
the locking nut
RudderServoAssembly
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn

19
4. Turn onyourradiotokeep the
servoneutral. Mount thepre-installed
boll linktotherudderarmwithout
locking nut. Put twobrass tube
through thecableand threadthrough
the couplerhole. Ensure the cables
are straight
NOTICE:The couplerisbest to
threadhalf wayintoball linkfor
furthertightening next
5. Crimptheminplacewithcrimping
pliers
6. Cutawayexcess cable
RudderServoAssembly
PDF 件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn