Pilot Communications Predator Sport Jet 90" User manual

Predator Sport Jet 90”
USER MANUAL
WINGSPAN:2200mm
LENGTH:2280mm

● Thank you for purchasing our Predator Sport Jet plane. we strive to achieve a good
quality quick build ARF aircraft .
It requires the least amount of assembly of any ARF kit to obtain the maximum
performance.
● Both the design and manufacturing have been undertaken to the highest standards,
using best quality hardware, covering, wood & glue during factory construction stage.
● By optimal weight and balance along with reliable construction, you will find this plane
ideal for flying.
We hope that every effort and service we offer will, in turn, give you confidence using
PILOT Models.
● Have a wonderful time flying your aircraft in a suitable safe space!
Introduction
Warrant
● All Pilot-RC products are guaranteed against defects for 30 days of receiving your
airplane. This warranty is limited to construction or production defects in both material and
workmanship , it does not cover any component parts damaged through use or
modification .
● The manufacture cannot supervise the assembly, operation or maintenance, and is not
responsible for radio malfunctions. Please ensure your radio system is in good condition.
We are not responsible for any accident or damage while using this product. It is
impossible to determine for certain whether crash damage was the result of improper
installation of our products, a radio system failure, or pilot error. Model airplane owners use
our products at their own risk.
●
Pilot
-
RC will not be liable for any costs, unless agreed and proved beyond doubt the
●
Pilot
-
RC will not be liable for any costs, unless agreed and proved beyond doubt the
failure was due to faulty materials or fabrication. Any agreed cost will not exceed the cost
of the airframe and not include engine, radio equipment or third party claims.
● Should you wish to return a product or receive replacement parts, all shipping cost must
be paid by the customer.
Attention
● 1. Do not regard this plane as a toy!
● 2. To ensure safety, please read the instruction manual thoroughly before assembly.
● 3. Building and operating an RC Plane of this nature
requires previous experience and competence to an experienced level. This plane is not for
a beginner!
● 4. If you are in doubt have an experienced pilot at hand. Diligent practicing and correct
guidance is essential, accidents can cause bodily harm and property damage.
● 5. Seek assistance from an experienced person or airplane model clubs in assembly,
operation and maintenance to ensure successful training.
● 6. Fly only in a registered RC model club airfield that is approved by your local
Academy of Model Aeronautics (AMA).
● Pilot-RC has the right to revise the plane, the instructions and the limited warranty
without notice. If you have any problems and questions please contact Pilot –RC：
Email: pilot[email protected] , [e-mail]
Phone:[phone]
FAX: [phone]
Address: No.34, Chengnan Er Road , Zhongshan city, 528400, Guangdong Province, China

Install kit contents
Install kit contents:
（Some contents like fuel tank etc… has already installed in fuselage）
Aluminum tube:
Accessories pack：

Install kit contents
Accessories pack includes：
Socket head cap screws
Counterstunk cross screws
Cross round head with medium screws
Tapping screws
Hexagon screw in metric system(SHCS)
Battery bandage
Servo aluminum angle
Metric Allen Wrench
Push rot wrench
Wring clamp
Crowbar
Crowbar
Push rot:
Oil nipple suit
Extension cord:
(Some of accessories like screw/cord etc… isn’t in this accessories pack)
Epoxy Adhesives
Cyanocrylate adhesives
X-Acto and Saw knives
Sandpaper
Thread lock
Aircraft stand or support
Other Accessories Need To Complete:

Landing gear module(optional):
Landing gear(accessories included):
Landing gear
Pilot landing gear controller
Install kit contents

Servo module(optional):
Servo:
PY20AH 8
Servo arm:
Pilot Futaba aluminum alloy 0.8” 1
Pilot Futaba aluminum alloy 1.2” 7
Install kit contents

Landing gear assembly
Landing gear assembly:
Retract Landing Gear Installation, Predator Jet come with electric-
landing gear and brakes.

Landing gear assembly - nose
Install the servo to the nose landing gear.
Install the servo arm and the push rod. Adjust it to make sure the plane can go
straight approx. You still can adjust by radio after install it.

Place the nose gear to the mounting and adjust it to the correct position, then mark
the 4 mounting screws hole.
Landing gear assembly - nose
Before you drilling the mounting screws hole , please make sure there is nothing to
get stuck when it open and close.

Landing gear assembly - nose
After installation
Carefully arrange the nose gear retract
wire lead and the steering wire as well ...
Thanks to the “Test” function of the Pilot
-
Install the nose retract gear to the
fuselage.
Thanks to the “Test” function of the Pilot
-
Rc controller unit, you can test the
correct and free working of the system
without the need for your transmitter or
receiver, just connect a battery direct to
the controller.

Landing gear assembly - main
Recommend to use this 4 in MPX style connector from Pilot-RC. It’s
an optional parts.
.Connect all servo / landing gear
/ brakes wire.
2.The multi connector 4 in
out from the opening hole…

Wing Ser o/Flaps Assembly
The control horns are pre-installed at the factory, ready for use.
1.Take out the aileron / flaps plating from the wing.
With the wings upside down,
position the gear in inside
the wing on the mounting
brackets and mark the
location for the screws.
Double check the positioning
of your gear before drilling
any holes. Make sure that
the gear movement is free of
2.Use the supply L-shape
aluminium braket to install the servo.
Use 1.2 inch servo arm, install the
servo arm to the servo and mark the
drilling hole... Refer to pic below.
the gear movement is free of
any obstacles.
Please take care when
drilling not to drill through
the wood and out through
the composite shell of the
wing.

3.Attach the included pushrods and ball links between the servo arm and the control
horn.
Wing Ser o/Flaps Assembly
4.Servo and servo arm installed

Wing Ser o/Flaps Assembly
5.Aileron servo / Flaps servo installed. 6.Use a thin ply as a back plate and
installed the 4 in 1 connector , use 5 min
epoxy to glue it from inside of the
fuselage.
7.Just one connector for aileron/flaps/landing gear/brakes.
One side of the connector can be screwed to the fuselage, while the other is left
inside the wing, loose, for easy connections.

Ele ator/ Rudder Ser o Assembly
Rudder servo assembly
The control
horns are
pre-installed
at the
factory,
ready for
use.
2.Insert the servo into the
rudder, in its allocated slot, with
the servo shaft closest to the
rudder. 3.Screw the servo in place, and then
install the servo arm on to the servo,
making sure that this is centred .
Attach the included pushrods and
ball links between the servo arm and
the control horn.

Ele ator/ Rudder Ser o Assembly
1.The rudder extension wire
connector.
2. Find the 2 pcs M4 cap screws to
tighten it. It will hold the rudder
position

Ele ator/ Rudder Ser o Assembly
Elevators
1.Put in the servo to the precut slot
in the elevator.
2.Screw the servo in place, and then
install the servo arm on to the servo,
making sure that this is centred
3: The other side of the
servo connector glue at
the side of the fuselage,
just a drop of CA or 5
min epoxy to glue it.

Ser o Wire Arrangements
1.You will find a top tube in the
top section of the fuselage! Servo
wire will slide in from the plastic
tube all the way out from the tube.
2.You can use a fire proof tubing to keep
the wire all isolate from heat.
3.To keep all the wire away from
heat best…

Ser o Wire Arrangements
1.Next step is to get all servo wire go
through the tube under the fuel
tank...showed as the picture below.
2.Predator jet come with high quality 2
in1 Kevlar fuel tank. Kevlar smoke tank is
optional parts.
240ml
UAT
3.There are two fuel tank as seen in the
picture, top one is the smoke tank and
the bottom one is the main fuel tank with
UAT build in ..

Tank Arrangement
The 90” predator use PilotRC 2 in 1 Kevlar tank. It’s included
4600ml fuel tank, and 240ml UAT(and you can choose the 2000ml
smoke tank as optional).