Pilot Communications J-10 Jet 107" User manual

J-10 Jet 107”
USER MANUAL
WINGSPAN:1650mm
LENGTH:2700mm

Introduction
Warrant
!All Pilot-RC products are guaranteed against defects for 30 days of receiving your airplane. This
warranty is limited to construction or production defects in both material and workmanship , it does
not cover any component parts damaged through use or modification .
!The manufacture cannot supervise the assembly, operation or maintenance, and is not
responsible for radio malfunctions. Please ensure your radio system is in good condition. We are
not responsible for any accident or damage while using this product. It is impossible to determine
for certain whether crash damage was the result of improper installation of our products, a radio
system failure, or pilot error. Model airplane owners use our products at their own risk.
!Pilot-RC will not be liable for any costs, unless agreed and proved beyond doubt the failure was
due to faulty materials or fabrication. Any agreed cost will not exceed the cost of the airframe and
not include engine, radio equipment or third party claims.
!Should you wish to return a product or receive replacement parts, all shipping cost must be paid
by the customer.
Attention
!1. Do not regard this plane as a toy!
!2. To ensure safety, please read the instruction manual thoroughly before assembly.
!3. Building and operating an RC Plane of this nature
requires previous experience and competence to an experienced level. This plane is not for a
beginner!
!4. If you are in doubt have an experienced pilot at hand. Diligent practicing and correct guidance
is essential, accidents can cause bodily harm and property damage.
!5. Seek assistance from an experienced person or airplane model clubs in assembly, operation
and maintenance to ensure successful training.
!6. Fly only in a registered RC model club airfield that is approved by your local Academy of
Model Aeronautics (AMA).
"
!Pilot-RC has the right to revise the plane, the instructions and the limited warranty without notice.
If you have any problems and questions please contact Pilot –RC：
Email: [email protected] , [email protected]
Phone:[phone]
FAX: [phone]
Address: No.34, Chengnan Er Road , Zhongshan city, 528400, Guangdong Province, China
!Thank you for purchasing our 2.7m(107”) J-10 Jet plane. we strive to achieve a good quality
quick build ARF aircraft .
It requires the least amount of assembly of any ARF kit to obtain the maximum performance.
!Both the design and manufacturing have been undertaken to the highest standards, using best
quality hardware, covering, wood & glue during factory construction stage.
!By optimal weight and balance along with reliable construction, you will find this plane ideal for
flying.
We hope that every effort and service we offer will, in turn, give you confidence using PILOT
Models.
!Have a wonderful time flying your aircraft in a suitable safe space!

Install kit contents
Install kit contents:
（Some contents like fuel tank etc… has already installed in fuselage）
Carbon tube：The outer diameter is 35mm, the wall thickness is 1.5mm,
and the length is 710 mm.
Landing gear module(optional):
Landing gear
Pilot landing gear controller

Accessories pack includes：
Hexagon screws in metric system(SHCS)
Tapping screws
Metric Allen Wrench
Push rot wrench
V teeth steel wire
Push rot
Wring clamp
Gasket
Battery bandage
Oil nipple suit
Extension cord
Crowbar
(Some of accessories like screw/cord etc… isn’t in this accessories pack)
Install kit contents
Accessories pack：

Servo module(optional):
Servo:
PW20AH 4
PY65AH 1
PY12AH 1
Servo arm:
Pilot Futaba aluminum alloy 0.8” 2
Pilot Futaba aluminum alloy 1.2” 3
Pilot Futaba aluminum alloy 1.6” 2
Install kit contents
Other Accessories Need To Complete:
Epoxy Adhesives
Cyanocrylate adhesives
X-Acto and Saw knives
Sandpaper
Thread lock
Aircraft stand or support

Front landing gear assembly
1: Install the servo to the nose landing gear.
2: Install the servo arm and the push rod. Adjust it to make sure the plane can go
straight approx. You still can adjust by radio after install it.

3: Place the nose gear to the mounting and adjust it to the correct position, then
mark the 4 mounting screws hole.
Front landing gear assembly
4: Before you drilling the mounting screws hole , please make sure there is nothing
to get stuck when it open and close.

1.Use M4 *14 screw to lock on the reserved space，and use
special fixed aluminum sheet to connect left and right for
reinforcement.
Landing gear assembly - main

Landing gear assembly - main
2.Check the main landing gear for interference.

Wing Servo Assembly
The control horns are pre-installed at the factory, ready for use..screw the servo to
the servo plate then install the servo arm on to the servo, making sure that this is
centred

Rudder Servo Assembly
1.Insert the servo into the precut servo mount. screw the servo in place, and then
install the servo arm on to the servo, making sure that this is centred.

Elevator Servo Assembly
2.Next is the elevators. as follows, the servo is fixed.
put in the servo to the precut slot in the elevator. .screw the
servo in place, and then install the servo arm on to the servo,
making sure that this is centred.

Installation of Vector Nozzle

Distance of vector rotation
Installation of engine and vector is completed.
Distance between Rear End of Engine and Vector Leading Edge
15mm

Installation of Vector Nozzle
1. Fixing Vector Servo Machines and Fixing Servo Machine Lines
X-axis servo fixed
Y-axis servo fixed

Tank Arrangement
The 106” J10 use PilotRC 5000ml oil tank.
Anti-bubble oiltank:250ml
Fuel vent

To arrange the fuel tank, connect all the oil tube(or you can
connect it later), and stick the Velcro stick on the tank support
frame. Also, you need stick the Velcro stick on the fuel tank, to
arrange the tank on the support frame, use Velcro stick tape to
straining the tank.
Installation of main oil tank and Smoke tank
1.Fixing of Main Oil Tank

Installation of main oil tank and Smoke tank
2.Fixing of Smoke Pull Oil Tank

Installation position of UAT and smoke pump

Installation of each controller
On top of the nose gear.