Pilz PSEN cs1.1n User manual

PSEN cs1.1n
Operating Manual-22178-EN-06
}PSEN sensor technology

Preface
This document is the original document.
Where unavoidable, for reasons of readability, the masculine form has been selected when
formulating this document. We do assure you that all persons are regarded without discrim-
ination and on an equal basis.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for the user's internal purposes. Suggestions and comments for improving this documenta-
tion will be gratefully received.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital

Contents
Operating Manual PSEN cs1.1n
22178-EN-06 | 3
Introduction ............................................................................................................................5
Validity of documentation.......................................................................................................... 5
Using the documentation .......................................................................................................... 5
Definition of symbols................................................................................................................. 5
Safety ...................................................................................................................................... 6
Intended use ............................................................................................................................. 6
Safety regulations ..................................................................................................................... 7
Safety assessment ................................................................................................................... 7
Use of qualified personnel ........................................................................................................ 7
Warranty and liability ................................................................................................................ 7
Disposal .................................................................................................................................... 7
For your safety.......................................................................................................................... 8
Unit features ...........................................................................................................................8
Function description ............................................................................................................. 9
Block diagram ........................................................................................................................... 9
Operating distances.................................................................................................................. 9
Lateral and vertical offset.......................................................................................................... 10
Wiring ......................................................................................................................................10
Pin assignment, connector and cable....................................................................................... 11
Connection to evaluation devices ........................................................................................ 11
Teaching in the actuator ....................................................................................................... 13
Installation ..............................................................................................................................13
Adjustment ............................................................................................................................. 14
Operation ................................................................................................................................14
Dimensions in mm .................................................................................................................15
Technical details ....................................................................................................................16
Safety characteristic data ......................................................................................................... 18
Supplementary data ..............................................................................................................19
Radio approval.......................................................................................................................... 19
Order reference ......................................................................................................................19
System...................................................................................................................................... 19
Accessories .............................................................................................................................. 19

Contents
Operating Manual PSEN cs1.1n
22178-EN-06 | 4
EC declaration of conformity ................................................................................................ 21
UKCA-Declaration of Conformity ......................................................................................... 21

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 5
Introduction
Validity of documentation
This documentation is valid for the product PSEN cs1.1n. It is valid until new documentation
is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
Using the documentation
This document is intended for instruction. Only install and commission the product if you
have read and understood this document. The document should be retained for future ref-
erence.
Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 6
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Safety
Intended use
The safety functions of the safety switch are:
}Safe shutdown of safety outputs when the actuator is removed beyond the assured re-
lease distance sar or when the actuator is not detected
}Remain shut down safely after the actuator has been removed
The safety switch meets the requirements in accordance with:
}EN 60947-5-3: PDDB with the actuator PSEN cs1.1
}EN 62061: SIL CL 3
}EN ISO 13849-1: PL e (Cat. 4)
}ENISO14119: Coding level Low, type 4
The safety switch may only be used with the corresponding actuator PSEN cs1.1.
The safety level PL e (Cat. 4)/SIL CL 3 is only achieved if
}the safety outputs use 2-channel processing.
Improper use
The following is deemed improper use in particular
}Any component, technical or electrical modification to the product,
}Use of the product outside the areas described in this operating manual,
}Use of the product outside the technical details (see Technical details [ 16]).
NOTICE
EMC-compliant electrical installation
The product is designed for use in an industrial environment. The product
may cause interference if installed in other environments. If installed in other
environments, measures should be taken to comply with the applicable
standards and directives for the respective installation site with regard to in-
terference.

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 7
Safety regulations
Safety assessment
Before using a device, a safety assessment in accordance with the Machinery Directive is
required.
The product as an individual component fulfils the functional safety requirements in accord-
ance with EN ISO 13849 and EN 62061. However, this does not guarantee the functional
safety of the overall plant/machine. To achieve the relevant safety level of the overall plant/
machine’s required safety functions, each safety function needs to be considered separ-
ately.
Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by persons who are competent to do so.
A competent person is a qualified and knowledgeable person who, because of their train-
ing, experience and current professional activity, has the specialist knowledge required. To
be able to inspect, assess and operate devices, systems and machines, the person has to
be informed of the state of the art and the applicable national, European and international
laws, directives and standards.
It is the company’s responsibility only to employ personnel who
}Are familiar with the basic regulations concerning health and safety / accident prevention,
}Have read and understood the information provided in the section entitled Safety
}Have a good knowledge of the generic and specialist standards applicable to the specific
application.
Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended,
}Damage can be attributed to not having followed the guidelines in the manual,
}Operating personnel are not suitably qualified,
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
Disposal
}In safety-related applications, please comply with the mission time TM in the safety-related
characteristic data.
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 8
For your safety
WARNING!
Loss of safety function due to manipulation of the interlocking device
Manipulation of the interlocking device may lead to serious injury and death.
– You should prevent any possibility of the interlocking device being
manipulated through the use of a spare actuator.
– Keep the substitute actuator in a safe place and protect it from unau-
thorised access.
– If substitute actuators are used, these must be installed as described
under Installation [ 13].
– If the original actuators are replaced with substitute actuators, the ori-
ginal actuators must be destroyed before disposal.
}Do not remove the connector's protective cap until you are just about to connect the unit.
This will prevent potential contamination.
Unit features
}Transponder technology for presence detection
}Pilz coding type: Coded
}Dual-channel operation
}2 safety outputs
}LED display for:
– State of the actuator
– Supply voltage/fault
}4 directions of actuation

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 9
Function description
The safety outputs may have a high or low signal, depending on the position of the actu-
ator.
In a safe condition the safety outputs are in the OFF state.
State of the outputs:
Actuator in the response
range
Safety output 12 Safety output 22
Yes High High
No Low Low
Block diagram
A1 A2
Power
12 22
Receiver Actuator
Operating distances
On
Off
Legend:
}Sao Assured operating distance: 15 mm
}So Typical operating distance: 21 mm
}Sr Typical release distance: 32 mm
}Sar Assured release distance: 40 mm

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 10
Lateral and vertical offset
Lateral offset Vertical offset
[1]
[2]
[3]
[4] [4]
[5]
[6]
Power / Fault
Safety Gate
Input
[4]
[4]
0 10 20
0 10 20
40
-20
-40
20
10
30
-10
-30
0
Legend
[1] Hysteresis
[2] Typical operating distance SO
[3] Typical release distance Sr
[4] Offset in mm
[5] Operating distance in mm
[6] Response range
Wiring
Please note:
}Information given in the "Technical details" must be followed.
}Switch off the supply voltage before disconnecting the plug-in connection.
}Make sure that when connecting or separating the connector the pollution degree 1 or 2
is maintained.
}The power supply must meet the regulations for extra low voltages with protective elec-
trical separation (SELV, PELV).
}The outputs of the safety switch must have a protective separation to voltages over 60 V
AC.
}The supply voltage to the safety switch must be protected with a 2 A to 4A quick-acting
fuse.
}Ensure the wiring and EMC requirements of EN 60204-1 are met.

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 11
Pin assignment, connector and cable
12
3
5
4
5-pin M12 male connector
PIN Pin
designation
Function Wire colour
1 A1 +24 UB Brown
2 12 Output, channel1 White
3 A2 0 V UB Blue
4 22 Output, channel2 Black
5 - Do not connect Grey
The wire colour also applies for the cable available from Pilz as an accessory.
Connection to evaluation devices
Make sure that the selected evaluation device has the following property:
}OSSD signals are evaluated through 2 channels with plausibility monitoring
Note:
}Information given in the Technical details [ 16] must be followed.
Connection diagram, single connection
Actuator
Evaluation device
Safety switch

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 12
Suitable Pilz evaluation devices are, for example:
}PNOZelog for safety gate monitoring
}PNOZpower for safety gate monitoring
}PNOZsigma for safety gate monitoring
}PNOZ X for safety gate monitoring
}PNOZmulti for safety gate monitoring
Configure the switch in the PNOZmulti Configurator with switch type 3.
}PSS for safety gate monitoring with standard function block SB064, SB066 or
FS_SafetyGate
}PSSuniversal PLC for safety gate monitoring with function block FS_SafetyGate
The correct connection to the respective evaluation device is described in the operating
manual for the evaluation device. Make sure that the connection is made in accordance
with the specifications in the operating manual for the selected evaluation device.
The connections to two evaluation devices are shown on the following pages, by way of ex-
ample:
}PNOZ s3 and
}PNOZmulti
PNOZ s3
PSENcode
0 V
24 V
A1
A2
S12
A1
A2
Y32
12
22
2
1
3
4
5
PNOZ s3
S22
PNOZmulti
I0
I1
12
22
1
3
A1
A2
0 V
24 V
4
2
5
PNOZmulti PSENcode
n.c.

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 13
Teaching in the actuator
Any approved Pilz actuator (see Intended use [ 6]) is detected as soon as it is brought
into the response range.
Installation
CAUTION!
Potential loss of safety function due to changed device properties
The unit's properties may be affected if installed in an environment contain-
ing electrically or magnetically conductive material.
– Please check the operating distances and the assured release dis-
tance.
}The safety switch and actuator should be installed opposite each other in parallel.
– Make sure that the actuator is aligned to the marking on the sensor that guarantees
the operating distance required by the plant design (see Operating distances [ 9]).
}Safety switches and actuators should be permanently secured using M5 safety screws
with a flat head (e.g. M5 cheese-head or pan head screws).
}Protect the actuator from contamination.
}Torque setting: Please note the information provided under Technical details [ 16].
}The distance between two safety switches must be maintained (see Technical
details [ 16]).
}Make sure that the safety switch and actuator cannot be used as an end stop.
}Please note the installation measures in accordance with EN ISO 14119 for a safety
switch design 4 and with level of coding Low.
}For simpler installation, the mounting brackets (see Order reference for
Accessories [ 19]) can be used.
}If using angled connector plugs, note the defined angle of the cable routing.
CAUTION!
Possible loss of the safety function by changing the release distance
Sar with non-flush installation
Installing the safety switch non-flush within electrically or magnetically con-
ductive material, the value for the assured release distance Sar can change.
– Check the assured release distance Sar.

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 14
Procedure:
Fig.: Sensing faces on the sensor
1. Drill holes (for M5 screws) in the mounting surface to secure the actuator and sensor
(see Dimensions in mm [ 15]).
2. Use a screw to fix the sensor to the mounting surface.
Make sure that the sensor marking that is be used for operation can be operated using
the actuator from the right side.
3. Do not fully tighten the second screw on the safety switch.
4. Use a screw to fix the actuator to the mounting surface.
Make sure that the actuator with the printed side points towards the marking on the
sensor.
5. Do not fully tighten the second screw on the actuator.
6. Align the safety switch and tighten the screws.
7. Align the actuator and tighten the screws.
Adjustment
}The stated operating distances (see Technical details [ 16]) only apply when the
safety switch and actuator are installed facing each other in parallel. Operating distances
may deviate if other arrangements are used.
}Note the maximum permitted lateral and vertical offset (see Operating distances [ 9]
and Lateral and vertical offset [ 10]).
Operation
NOTICE
The safety function should be checked after initial commissioning and each
time the plant/machine is changed. The safety functions may only be
checked by qualified personnel.

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 15
Check the function of the safety switch before commissioning.
Status indicators:
}"POWER/Fault" LED lights up green: The unit is ready for operation
}"Safety Gate" LED lights up yellow: Actuator is within the response range
Fault indicator:
}"POWER/Fault" LED lights up red: Error message.
Remedy: Rectify fault and interrupt power supply.
Dimensions in mm
72
45
21,5
20
61
M12x1
40
40
5,1 1
5,5
30
20
74
40
11
4
40
5,3
30
30
0,5

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 16
Technical details
General
Certifications CE, EAC, FCC, IC, TÜV, UKCA, cULus Listed
Sensor's mode of operation Transponder
Coding level in accordance with EN ISO 14119 Low
Design in accordance with EN ISO 14119 4
Classification in accordance with EN 60947-5-3 PDDB
Pilz coding type Coded
Transponder
Frequency band 122 kHz - 128 kHz
Max. transmitter output 15 mW
Electrical data
Supply voltage
Voltage 24 V
Kind DC
Voltage tolerance -20 %/+20 %
Output of external power supply (DC) 2 W
Max. inrush current at UB 0,12 A
Max. switching frequency 3 Hz
Max. cable capacitance at the safety outputs
No-load, PNOZ with relay contacts 40 nF
PNOZmulti, PNOZelog, PSS 70 nF
No-load current 50 mA
Semiconductor outputs
Number of OSSD safety outputs 2
Switching current per output 500 mA
Breaking capacity per output 12 W
Potential isolation from system voltage No
Short circuit-proof yes
Residual current at outputs 10 µA
Voltage drop at OSSDs 3,5 V
Lowest operating current 0 mA
Utilisation category in accordance with EN 60947-1 DC-12
Times
Test pulse duration, safety outputs 450 µs
Switch-on delay
after UB is applied 1 s
Actuator typ. 80 ms
Actuator max. 150 ms
Delay-on de-energisation
Actuator typ. 40 ms
Actuator max. 260 ms
Risk time in accordance with EN 60947-5-3 260 ms
Supply interruption before de-energisation 20 ms

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 17
Times
Simultaneity, channel 1 and 2 max. ∞
Environmental data
Ambient temperature
In accordance with the standard EN 60068-2-14
Temperature range -25 - 70 °C
Storage temperature
In accordance with the standard EN 60068-2-1/-2
Climatic suitability
In accordance with the standard EN 60068-2-78
Humidity 93 % r. h. at 40 °C
EMC EN 60947-5-3
Vibration
In accordance with the standard EN 60947-5-2
Frequency 10 - 55 Hz
Amplitude 1 mm
Shock stress
In accordance with the standard EN 60947-5-2
Acceleration 30g
Duration 11 ms
Airgap creepage
Overvoltage category III
Pollution degree 3
Rated insulation voltage 75 V
Rated impulse withstand voltage 0,8 kV
Protection type
Housing IP67
Operating distances
Assured operating distance Sao 15 mm
Typical operating distance So 21 mm
Assured release distance Sar 40 mm
Typical release distance Sr 32 mm
Repetition accuracy switching distances 10 %
Change of operating distance with temperature
changes +-0,01mm/°C
Typ. Hysteresis 3 mm
Mechanical data
Actuator 1 PSEN cs1.1
Min. distance between safety switches 400 mm
Sensor flush installation in accordance with EN
60947-5-2 yes, follow installation guidelines
Connection type M12, 5-pin male connector
Material
Top PBT
Max. torque setting for fixing screws 1 Nm

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 18
Mechanical data
Dimensions
Height 75 mm
Width 40 mm
Depth 40 mm
Actuator dimensions
Height 11 mm
Width 40 mm
Depth 40 mm
Weight of safety switch 130 g
Weight of actuator 20 g
Weight 150 g
Where standards are undated, the 2016-10 latest editions shall apply.
Safety characteristic data
NOTICE
You must comply with the safety characteristic data in order to achieve the
required safety level for your plant/machine.
Operating
mode
EN ISO
13849-1:
2015
PL
EN ISO
13849-1:
2015
Category
EN62061
SIL CL
EN62061
PFHD [1/h]
IEC61511
SIL
IEC61511
PFD
EN ISO
13849-1:
2015
TM [year]
2-ch. OSSD PL e Cat. 4 SIL CL 3 4,10E-09 –1,10E-04 20
Explanatory notes for the safety-related characteristic data:
}The SIL CL value in accordance with EN 62061 corresponds to the SIL value in accord-
ance with EN 61508.
}TM is the maximum mission time in accordance with EN ISO 13849-1. The value also ap-
plies as the retest interval in accordance with EN 61508-6 and IEC 61511 and as the
proof test interval and mission time in accordance with EN 62061.
All the units used within a safety function must be considered when calculating the safety
characteristic data.
INFORMATION
A safety function's SIL/PL values are not identical to the SIL/PL values of
the units that are used and may be different. We recommend that you use
the PAScal software tool to calculate the safety function's SIL/PL values.

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 19
Supplementary data
Radio approval
USA/Canada
FCC ID:
IC:
FCC/IC-Requirements:
This product complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standards.
Operation is subject to the following two conditions:
1) this product may not cause harmful interference, and
2) this product must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made to this product not expressly approved by Pilz may void the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Le présent produit est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) le produit ne doit pas produire de brouillage, et
(2) l'utilisateur de le produit doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
VT8-PSENCS1
7482A-PSENCS1
Order reference
System
Product type Features Connection type Order no.
PSEN cs1.1n/PSEN cs1.1 Safety gate system, coded 5-pin M12 male connector 540003
PSEN cs1.1n (switch) Safety switch, coded 5-pin M12 male connector 540053
PSEN cs1.1 Actuator, coded 540080
Accessories
Installation material
Product type Features Order no.
PSEN bracket Mounting bracket 532110
PSEN mag/cs bracket
straight
Mounting aid 532111
PSEN screw M4x20 10pcs Safety screws made from stainless steel with one-way slot 540313
PSEN screw M4x26 10pcs Safety screws made from stainless steel with one-way slot 540314
PSEN screw M5x10 10pcs Safety screws made from stainless steel with one-way slot 540311
PSEN screw M5x20 10pcs Safety screws made from stainless steel with one-way slot 540312
PSEN cs1/2 bracket cable
fix
Mechanical protection against defeat, protecting against unau-
thorised cable disconnection or damage for safety switches
PSENcodecs1/2, PSENcode cs5/6M12, PSENslock
532112

PSEN cs1.1n
Operating Manual PSEN cs1.1n
22178-EN-06 | 20
Cable
Product type Connection 1 Connection 2 Length Order No.
PSS67/PDP67 cable
M12-5sf
straight, M12, 5-pin, socket straight, M12, 5-pin,
connector
3 m 380208
5 m 380209
10 m 380210
20 m 380220
30 m 380211
PSS67/PDP67 cable
M12-5af
Angled, M12, 5-pin, socket Angled, M12, 5-pin,
connector
3 m 380212
5 m 380213
10 m 380214
30 m 380215
PSEN cable M12-5sf straight, M12, 5-pin, socket Open cable 3 m 630310
5 m 630311
10 m 630312
20 m 630298
30 m 630297
PSEN cable M12-5af Angled, M12, 5-pin, socket Open cable 3 m 630347
5 m 630348
10 m 630349
30 m 630350
PDP67 F 8DI ION Decentralised input module IP67 for PNOZmulti 773600