Pineapple RYNO User manual

REQUIRED
ITEMS
RYNO®CUBEBED FLOORFIXING
These instructions apply only when fixing to a concrete floor with no obstructions (e.g. under floor heating,cables,
plumbing,etc.).When fixing to any other surface,or with obstructions, please contact your Pineapple representative
for further advice.
N.B if fitting against coving there are several options to create a safe installation:
a Cut the coving in the area that the bed sits in
a Trim the base ofthe bed to fit the coving
a Push the bed as close to the wall as possible and infill the gap
a
4 x fixing templates
a
4 x floor brackets
a
4 x locking bolts
a 
4 x 8mm filler rod
a 
4 x 8mm filler rod
a
4 x flat metal plates
a
8 x M10 bolts
a 
Masking tape
a 
8mm wood drill bit
a 
16 x concrete hardware fixings
a 
5mm Allen key
Only provided with the
floor fixed version
[phone]
T
E
[e-mail]
V3 July 2023

04
01
Attach the 4 x flat plates to the underside of
the bed with the supplied M10 bolts
02
03
Place bed in desired location and mark
its outline with masking tape.Use the
overhanging edge of the bed as the guide
Remove bed and place the fixing templates
onto the floor at each cornerof the marked
area.Templates are marked; FL-Front Left,
FR-Front Right,BL-Back Left, BR-Back Right.
(The front of the bed has the recessed area
for sitting)
Using the template mark then drill the floor
in each bracket location with the x4 fixing
points.Take note of the bed sliding direction
– as marked withthe arrows.(The bed slides
underthe brackets from left to right in this
example)
RYNO®CUBEBED FLOORFIXING
V3 July 2023
[phone]
T
E
[e-mail]

05
Remove the templates and bolt the brackets
to the floorusing appropriate hardware
fixings
06
07
Insert locking bolt facing outwards into one
or both front brackets (FL orFR) and screw
in only a few turns.(All 4 locking bolts can
be used if only the head end ofthe bed is
against a wall)
Use masking tape to markthe locations of
the locking bolts on the floor.This will help
to indicate where the holes will have to be
drilled
RYNO®CUBEBED FLOORFIXING
08
Lie bed on its front face and 40mm to the left
of its final position
[phone]
T
E
[e-mail]
V3 July 2023

09
Lowerthe bed over the brackets and push
lengthways 40mm so that it hooks into place
10
11
Drill though the side ofthe bed in line with
where the locking bolts will be (use 8mm
wood drill bit).Clear out any plastic swarf
(bed may need to be removed for this).The
drilling hole will line up with either end of a
‘slot’indent feature.
Insert theAllen key and find the head of the
locking screws.Tighten until the screw stops
turning.The bed should now be locked into
place
[phone]
T
E
[e-mail]
RYNO®CUBEBED FLOORFIXING
V3 July 2023
12
Tap in the filler rod to block access to the
locking screws

Ensure the properand adequate hardware is used to secure furniture
Ensure fastenings are appropriate forthe anchoring material
Use fastenings of an appropriate strength and considerusing security fixings in
challenging environments
Considerusing high strength thread-lockeron fastenings in challenging environments
Ensure all gaps are sealed with the appropriate anti-pick mastic afterproduct
installation if necessary
Please read all instructions carefullyto ensure proper installation.Failureto read and
follow instructions may result inadequate product installation and void of warranty
Pineapple shall not be held liable forany consequences caused bythe improper
installation ofproducts tothe installer orthe end user
DISCLAIMER
[phone]
T
E
[e-mail]
V3 July 2023