Pinnacle Protemp PT-170T-IDF-EU Manual

Model Numbers
PT-100T-IDF-EU / PT-170T-IDF-EU
© 2014 Pinnacle Products International, Inc.
668 Stony Hill Road #302 Yardley, PA 19067 USA
Fax: [phone] • Web: www.protemp-intl.com • Email: [email protected]
User’s Manual &
Operating Instructions
CONSUMER: READ AND SAVE THESE INSTRUCTIONS
732000001-14
®
GENERAL HAZARD WARNING:
READ AND UNDERSTAND ALL OF THE INSTRUCTIONS IN THIS MANUAL
BEFORE ASSEMBLING, STARTING, OR SERVICING THE HEATER. Be sure to comply with the
instructions and warnings provided with this heater. Failure to comply can result in fire or explosion
that can cause property loss, bodily injury, or loss of life. Only persons who can follow and
understand these instructions should operate or service this heater.
DANGER
NOT FOR USE IN RESIDENTIAL LIVING AREAS OR IN ENCLOSED SPACES
WITHOUT ADEQUATE VENTILATION. INDOOR USE PERMITTED ONLY FOR
THE TEMPORARY HEATING OF BUILDINGS OR STRUCTURES UNDER CONSTRUCTION,
ALTERATION OR REPAIR. This is an unvented portable heater that uses air (Oxygen) from within
the area in which it is used. Failure to provide adequate combustion and ventilation air will result in
asphyxiation, carbon monoxide poisoning, bodily injury or death. Refer to “Ventilation” on Page 8-9
DANGER
This appliance shall be installed in accordance with the rules in force,
and used only in sufficiently ventilated space. Consult instructions before
installation and use of this appliance.
WARNING

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
1
Table Of Contents
Safety Information.............................................1-2
Features and Specications.................................3
100T-IDF-EU Assembly.....................................4-5
170T-IDF-EU Assembly....................................6-7
Operation........................................................8-10
Ventilation.........................................................8-9
Maintenance.......................................................11
Wiring Diagram..................................................12
Troubleshooting Guide.......................................13
Exploded View..............................................14-15
Parts List.......................................................16-19
Safety Information
FIRE, BURN, INHALATION AND EXPLOSION HAZARD. Keep combustibles such
as; building materials, paper or cardboard a safe distance away from the heater
as recommended by these instructions. Never use the heater in spaces which contain products
such as; gasoline, solvents, paint thinners, dust particles, volatile or airborne combustibles or any
unknown chemicals. This is an unvented portable heater. It uses air (Oxygen) from the area in
which it is used. Adequate combustion and ventilation air must be provided.
WARNING
DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND THOROUGHLY
UNDERSTAND THESE SAFETY AND OPERATING INSTRUCTIONS.
Failure to comply with the precautions and instructions provided with this heater can result in death,
serious bodily injury, property loss or damage from the hazards of fire, soot production, explosions,
burns, asphyxiation or carbon monoxide poisoning. Only persons who can read and understand
these instructions should use or service this heater.
WARNING
Look for this icon throughout the manual for helpful tips on how to
assemble, use and clean your IDF Heater.
DO NOT START THE HEATER WHEN EXCESS OIL HAS ACCUMULATED.
WARNING
DO NOT START THE HEATER WHEN THE CHAMBER IS HOT.
WARNING
THE INSTALLATION OF THIS HEATER SHALL COMPLY WITH THE REGULATIONS OF THE
AUTHORITIES HAVING JURISDICTION.
Read The Instruction manual: When this symbol is
marked on a product, it means that the instruction
manual must be read.
WARNING! Never touch heater until heater
has cooled off.
This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience or and knowledge
if they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
2
Safety Information
The products described in this manual are
parafn indirect-red, forced air heaters. Parafn
forced air heaters are primarily intended for
use for temporary heating of buildings under
construction, alteration or repair. These
heaters are equipped with a heat exchanger
that separates the combustion exhaust from
the heated air. This appliance is rated at 98%
combustion efciency, but does produce small
amounts of carbon monoxide.
Carbon monoxide is toxic. Humans can tolerate
only small amounts of carbon monoxide and so
precautions should be taken to provide proper
ventilation. Failure to provide proper ventilation
in accordance with the instructions in this manual
can result in death.
People with breathing problems should consult a
physician before using this heater.
Early signs of carbon monoxide poisoning
resemble the u. Symptoms of improper
ventilation / carbon monoxide poisoning are:
Headache • Dizziness • Nausea • Dry Mouth
Sore Throat • Burning of Nose and Eyes
If you experience any of these symptoms:
GET FRESH AIR AT ONCE! Have your heater
serviced and check for proper ventilation. Some
people are more affected by carbon monoxide
than others. These include: pregnant women,
those with heart or lung problems, anemia or those
under the influence of alcohol or at high altitudes.
Not For Indoor Use. Indoor use permitted only
for the temporary heating of buildings under
construction, alteration or repair!
Provide at least a three square foot (2,800 sq
cm) opening of outside air for every 100,000
Btu / Hr heater rating. Refer to “Ventilation” on
page 8-9 for further instructions.
ALWAYS use only the electrical power (voltage and
frequency) specified on the model plate of the heater.
ALWAYS use only approved, grounded socket and
properly rated extension cables.
ALWAYS unplug the heater when not in use.
ALWAYS install the heater so that it is not directly
exposed to water spray, rain, dripping water, or wind.
If the supply cord is damaged, it must be
replaced by a special cord or assemble available
from the manufacturer, its service agent or
similarly qualied persons in order to avoid a
hazard
NEVER use fuels such as gasoline, benzine, paint
thinners or other oil compounds in this heater.
NEVER refill the heater’s fuel tank while the
heater is operating or still hot. This heater is
EXTREMELY HOT while in operation.
NEVER block air inlet (rear) or air outlet (front).
NEVER use duct work in front or rear of heater.
NEVER move or handle heater while still hot.
NEVER transport heater with fuel in tank.
NEVER use with an external fuel tank.
Keep all combustible materials away from this heater.
Minimum Clearance From Combustibles
100T-IDF-EU 170T-IDF-EU
Top 1.2 m 1.2 m
Sides 1.2 m 1.2 m
Front 2.4 m 2.4 m
ALWAYS locate heater on a stable and level surface.
If your heater is equipped with a thermostat,
once it is plugged in, it can start at anytime in
accordance with the thermostat setting.
RISK OF INDOOR AIR
POLLUTION!
WARNING
CARBON MONOXIDE POISONING
MAY LEAD TO DEATH!
WARNING
RISK OF BURNS, FIRE AND
EXPLOSION!
WARNING
RISK OF ELECTRIC SHOCK!
WARNING
CAUTION! HOT WHILE IN
OPERATION. DO NOT TOUCH.
KEEP CHILDREN, ANIMALS, CLOTHING AND
COMBUSTIBLES AWAY FROM HEATER.
WARNING

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
3
Specications
Features
Model # PT-100T-IDF-EU PT170T-IDF-EU
Rating: kW / Hr 30 50
Fuel Consumption: L/Hr 2.4 4.0
Fuel Tank Capacity: Liters 50 68
Pump Pressure: PSI /BAR 4.5 / 0.31 4.5 / 0.31
Volts: AC/Hz 230VAC / 50Hz 230VAC / 50Hz
Phase 1Ø 1Ø
Specications subject to change without notice.
Handle
Cord Wraps
Fuel Cap
Drain Plug
Fuel Tank
Upper Shell
Exhaust Vent
Hot Air Outlet
Lower Shell
Power Switch
Thermostat Knob
LED Display
Handle
Extension
Cord Wrap
Fuel Cap
Drain Plug
Fuel Tank
Upper Shell
Exhaust Vent
Hot Air Outlet
Lower Shell
Power Switch
Thermostat Knob
LED Displays
Models: PT-100T-IDF-EU
Models: PT-170T-IDF-EU
Figure 1
Figure 2

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
4
Assembly Instructions
Models: PT-100T-IDF-EU
- Remove the heater and all packaging
materials from the shipping carton.
Tools Needed:
- Phillips Head Screw Driver
- 8 mm open end wrench
- 19 mm open end wrench
What’s In The Box
50 mm Screws (4) 38 mm Screws (6) Nuts (10) Lock Washers (10)
Flat Washers (10) Axle Nuts (2) Spacers (2) Axle (1)
Tip: Be sure to remove the axle from the
side of the Styrofoam packaging. Tip: Use a power screwdriver and
locking wrench for easier assembly.
Cord Wraps (2) Wheels (2) Wheel Frame (1) Handle (1)

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
Assembly Instructions
Model: PT-100T-IDF-EU
1. Insert axle through holes in wheel support.
2. Slide the spacer onto axle.
3. Slide wheel onto axle and hold in place with
the axle nuts. (See Figure 3).
4. Place heater on wheel support and line up
holes on the fuel tank lip.
NOTE: Use lock washers and flat washers as
shown in figure 4 to secure the wheel frame
and handle to the tank.
5. Insert (2) short screws (38 mm) through the
first hole from the front in the tank lip on both
sides of the tank and tighten firmly. Make
certain all (2) screws are secure.
6. Attach rear handle with (2) long screws
(50 mm) and (2) nuts through the two holes in
the rear of the tank on both sides and tighten
firmly. Make certain all (4) screws are secure.
(See Figure 6)
7. Attach cord wraps to handle using (2) short
screws (38 mm) each.
Figure 3
Axle
Axle Nut Washer
Spacer
Tire
Wheel Support Frame
Figure 4
5

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
6
- Remove the heater and all packaging
materials from the shipping carton.
Tools Needed:
- Phillips Head Screw Driver
- 8 mm open end wrench
- 19 mm open end wrench
Assembly Instructions
Models: PT-170T-IDF-EU
What’s In The Box
Tip: Be sure to remove the axle from the
side of the Styrofoam packaging. Tip: Use a power screwdriver and
locking wrench for easier assembly.
64 mm Screws (4) 50 mm Screws (4) 38 mm Screws (4) Nuts (12)
Lock Washers (12) Flat Washers (12) Axle Nuts (2) Spacers (2)
Cord Wraps (2) Wheels (2) Wheel Frame (1) Handle (1)
Axle (1)

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
Assembly Instructions
Model: PT-170T-IDF-EU
1. Insert axle through holes in wheel support.
2. Slide the spacer onto axle.
3. Slide wheel onto axle and hold in place with
the axle nuts. (See Figure 5).
4. Place heater on wheel support and line up
holes on the fuel tank lip.
NOTE: Use lock washers and flat washers as
shown in figure 6 to secure the wheel frame
and handle to the tank.
5. Insert (2) short screws (50 mm) through the
first two holes from the front in the tank lip
on both sides of the tank and tighten firmly.
Make certain all (4) screws are secure.
6. Attach rear handle with (2) long screws
(64 mm) and (2) nuts through the two holes in
the rear of the tank on both sides and tighten
firmly. Make certain all (4) screws are secure.
(See Figure 6)
7. Attach cord wraps to handle using (2) short
screws (38 mm) each.
Figure 5
Axle
Axle Nut Washer
Spacer
Tire
Wheel Support Frame
7
Figure 6

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
Operation
Fueling The Heater:
Parafn
For optimal performance of this heater, it is
strongly suggested that parafn be used.
parafn has been rened to virtually eliminate
contaminants, such as sulfur, which can cause
a rotten egg odor during the operation of the
heater. Using diesel fuel can cause excess soot
production. Do not use Bio-Diesel as this fuel will
damage your heater’s seals and lter.
- NEVER use fuel such as, benzene, alcohol, white
glass, camp stove fuel, paint thinners, or other oil
compounds in this heater. THESE ARE VOLATILE
FUELS THAT CAN CAUSE A FIRE OR
EXPLOSION.
- NEVER store paraffin in the living space. Paraffin
should be stored in a well ventilated area outside
the living area.
- NEVER store paraffin in direct sunlight or near a
source of heat.
- NEVER use paraffin that has been stored from one
season to the next. Paraffin deteriorates over time.
OLD Paraffin WILL NOT BURN PROPERLY IN
THIS HEATER.
NOTE: Parafn should only be stored in a blue
container that is clearly marked “Parafn.” Never
store parafn in a red container. Red is associated
with gasoline.
Ventilation:
- Risk of indoor air pollution and Carbon
Monoxide Poisoning. Use heater only in well
ventilated areas.
- Refer to Safety Information on pages 1-2 for
information about Carbon Monoxide Poisoning.
- ALWAYS provide a fresh air opening in the heated
space of at least 2,800 cm
2
for each 29 kW / Hr. of
heater output. Provide a larger opening if more
heaters are being used.
Minimum Ventilation Opening Needed
100T-IDF-EU
170T-IDF-EU
3.0 ft.² 5.3 ft.²
2780 cm² 4870 cm²
NEVER FILL THE FUEL TANK
INDOORS. ALWAYS FILL
THE TANK OUTDOORS. BE SURE THAT
THE HEATER IS ON LEVEL GROUND WHEN
FUELING, AND NEVER OVERFILL THE TANK.
CAUTION
NEVER REFUEL THIS HEATER
WHILE IT IS HOT OR
OPERATING. FIRE OR EXPLOSION COULD
RESULT.
DANGER
CARBON MONOXIDE POISONING
MAY LEAD TO DEATH!
DANGER
8
DO NOT USE GASOLINE OR
CRANKCASE DRAININGS.
WARNING
This appliance is designed to
operate safely at a minimum
ambient temperature of -20° C.
WARNING
Use caution when servicing in
wet areas. Disconnect power
from the power mains and keep all electrical
components from becoming wet. Only a
qualified technician should service the
heater
WARNING
A qualified technician is
required to install, adjust and
where necessary; convert this heater for use
with other fuel types.
WARNING

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
Operation
Ventilation:
- This heater is equipped with a heat
exchanger. The heat exchanger removes the
combustion materials and exhaust from the
heated air.
- The combustion materials and exhaust
(Carbon Monoxide and fuel fumes) can be
vented using the top mounted vent.
- Follow the ventilation congurations below to
properly vent your heater for indoor use.
NEVER OPERATE THIS
HEATER IN AN ENCLOSED
SPACE WITHOUT PROPER VENTILATION.
DANGER
THIS HEATER CAN NOT BE
USED TO HEAT RESIDENTIAL
OR PERMANENT OCCUPANCIES.
DANGER
MIN 5M
MAX 8M
MIN 2M
100°
MIN 4M
MIN 4.5M
120°
9

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
Operation
Starting the Heater: (Ignition)
1. Fill the tank with paraffin or other approved
fuel until needle on fuel gauge points to “F”.
2. Replace fuel cap and tighten firmly.
3. Connect the heater to a three prong
(grounded) power source. You must use a
three prong (grounded) extension cord that is
at least 1.8 meters long and is properly rated
for this service.
4. Move power switch to “On” position. The LED
displays will illuminate.
5. The left display is the setting temperature.
Use the thermostat knob to raise or lower the
setting temperature as desired.
6. The right display is the ambient room
temperature.
7. The heater will ignite once the setting
temperature is higher than the ambient room
temperature.
NOTE: If if the heater still does not ignite,
refer to “Troubleshooting Guide” on page 12.
Stopping / Restarting Heater:
1. To stop the heater, move the power switch to
the “Off” position and unplug the power cord.
2. To restart the heater; wait 10 seconds and
follow ignition steps.
10
TIP: If the heater does not ignite, the
thermostat may be set too low. Turn
the control knob to a higher setting until the
heater ignites. If the heater does not ignite;
move switch to “Off” position, check steps 1-3
above and then move switch to “On” position.
Thermostat Knob
Power Switch
Setting Temperature Room Temperature
Control Panel
Figure 7

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
Maintenance
Long Term Storage:
Models 100T-IDF-EU / 170T-IDF-EU:
1. Drain fuel through the drain plug in the bottom
of the fuel tank.
2. Using a small amount of parafn, rinse and
swirl the parafn inside of the fuel tank, empty
the tank fully.
IMPORTANT: Never store leftover parafn
between seasons, using old fuel can damage
heater.
Service:
DO NOT TAMPER WITH THE UNIT. HAVE
A COMPETENT SERVICEMAN MAKE ANY
NECESSARY ADJUSTMENT OR REPAIRS.
Use only original equipment parts. The use of
alternate or third party components can cause
unsafe operating conditions.
We suggest following a maintenance schedule as
follows:
FUEL / FUEL TANK:
Flush tank every 200 hours of operation or as
needed.
DO NOT ush with water, use fresh parafn only.
NOZZLES:
Nozzles should be cleaned or replaced at least
once per heating season. Contaminated fuel could
make this necessary immediately. To clean dirt
from nozzle, blow compressed air through nozzle
front. It may be necessary to soak the nozzle in
paraffin to loosen any dirt particles.
SPARK PLUG:
Clean and re-gap every 600 hours of operation, or
replace as needed. After removing the spark plug,
clean the terminals with a wire brush.
See Figure 8.
PHOTOCELL:
The photocell should be cleaned using a cotton
swab dipped in alcohol or water at least once
per heating season, or more depending on
conditions. See Figure 17.
11
TIP: Follow the long term storage
instructions to ush the tank.
Never service heater while it is
plugged in or hot!
WARNING
XX
Figure 8
Figure 9

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
Wiring Diagram
12
PHOTOCELL
TEMPERATURE SENSOR
IGNITOR SOLENOID
POWER SWITCH
THERMOSTAT
MOTOR
230V ~ 50Hz
EARTH
NEUTRAL
LINE
Figure 10

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
13
Troubleshooting Guide
Problem Possible Cause Solution
Heater Ignites, but main PCB shuts
off after a short period of time.
Lamp ickers and LED display
shows “E1”.
1. Incorrect pump pressure.
2. Dirty input, output or lint lter.
3. Dirty fuel lter.
4. Nozzle is dirty.
5. Photocell lens is dirty.
6. Photocell not installed properly.
7. Photocell is defective.
8. Improper electrical connection
between main PCB and photocell.
1. Adjust pump pressure.
2. Clean / replace air or lint lter.
3. Clean / replace fuel lter.
4. Clean / replace Nozzle.
5. Clean / replace photocell.
6. Adjust photocell position
7. Replace photocell
8. Check wiring connections .
Heater will not operate or motor
runs for a short time.
Lamp ickers and LED display
shows “E1”.
1. No parafn in the fuel tank.
2. Incorrect pump pressure.
3. Corroded spark plug or incorrect
plug gap.
4. Dirty fuel lter.
5. Dirty nozzle.
6. Moisture in fuel tank.
7. Improper electrical connection
between transformer and circuit
board.
8. Ignitor wire not connected to spark
plug.
9. Defective ignitor.
1. Fill tank with fresh parafn.
2. Adjust pump pressure.
3. Clean / replace spark plug.
4. Clean / replace fuel lter.
5. Clean / replace nozzle.
6. Rinse fuel tank with clean, fresh
parafn.
7. Inspect all electrical connections.
8. Re-attach ignitor wire to spark plug.
9. Replace ignitor.
Lamp is ickering and LED display
shows “E2”.
1. Thermostat switch has failed. 1. Replace thermostat switch.
Poor combustion and / or excess
soot production.
1. Dirty input, output or lint lter.
2. Dirty fuel lter.
3. Poor quality of fuel.
4. PSI is too high or too low.
1. Clean / replace air or lint lter.
2. Clean / replace fuel lter.
3. Flush fuel tank and refuel heater.
4. Use proper pressure.
Heater does not turn on and the
lamp is not lit. “--”
1. Temperature limit sensor has
overheated.
2. No electrical power.
3. Fuse is blown.
4. Improper electrical connection
between temperature limit sensor
and circuit board.
1. Push power switch to “OFF and
allow heater to cool for 10 minutes.
Restart heater.
2. Check power cords for proper
connection and test the power
supply.
3. Check / replace the fuse.
4. Inspect all electrical connections.

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
Exploded View - 100T-IDF
14

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
15
Exploded View - 170T-IDF

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
16
Parts List - 100T-IDF
ALWAYS contact the manufacturer of this heater before replacing any parts
other than those specified or recommended in the servicing instructions.
WARNING
Item # Description Part Number
1 Frame 73-041-1000
2 Drain Plug 73-002-0252
3 Drain Plug Seal Ring 73-002-0401
4Fuel Filter Assembly 73-003-0101
5 Fuel Filter Joint 73-003-1001
6Fuel Tank 73-002-0102
7 Axle 73-041-0352
8 Cotter Pin 73-041-0307
9 Flat Gasket 73-014-0308
10 Wheel 73-041-0306
11 Wheel Screw 73-041-0309
12 PCB Bracket 73-027-1002
13 Ignitor Bracket 73-052-1002
14 PCB 73-027-1000
15 Fuel Tank Cap Gasket 73-006-0111
16 Fuel Tank Cap 73-006-0102
17 PCB 2 73-027-1100
18 Power Switch 73-038-0102
19 Thermo Cut-Off Adjusting Screw 73-019-1002
20 Knob 73-028-0501
21 Display Window 73-028-0401
22 Control Panel 73-028-0302
23 Fuel Gauge 73-002-1001
24 Front Support 73-041-0114
25 Ignitor 73-052-1000
26 Bottom Shell 73-001-0200
27 Air Outlet 73-001-0355
28 Ceramic Fiber Bracket 73-010-1101
29 Ceramic Fiber Fixed Support 73-010-1201
30 Ceramic Fiber 73-010-1001
31 Upper Front Shell 73-001-0102
32 Combustion Chamber 73-010-0102
33 Exhaust Hood / Flue Collar 73-010-0152

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
17
Item # Description Part Number
34 Upper Back Shell 73-001-0302
35 Photocell Assembly Bracket 73-016-1001
36 Photocell Assembly 73-016-0102
37 Thermo Cut-Off Bracket 73-019-1101
38 Thermo Cut-Off 73-019-1001
39 Wind Shield 73-015-1001
40 Nozzle Assembly 73-015-0102
41 Ignition Needle 73-015-3001
42 Nozzle Connector 73-015-2001
43 Nozzle Base 73-015-2101
44 Oil Filter 73-003-0131
45 Oil Filter Connector 73-003-1001
46 Nozzle Base Plate 73-015-2201
47 Side Plate 73-015-1201
48 Screw Nut 73-015-4001
49 Oil Filter Support 73-003-1101
50 Copper Bend Connector 73-015-5301
51 Fan 73-024-0102
52 Shrapnel Nut 73-016-2001
53 Rear Guard 73-016-0052
54 Fuel Filter Joint 2 73-003-2001
55 Sleeve 73-020-2001
56 Motor 73-020-1000
57 Motor Support 73-020-0103
58 Pump 73-020-0151
59 Back Frame 73-041-1001
60 Cord Holder 73-041-1002
61 Oil Pipe 73-003-0132
62 Back Support 73-041-0115
Parts List - 100T-IDF

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
18
Parts List - 170T-IDF
ALWAYS contact the manufacturer of this heater before replacing any parts
other than those specified or recommended in the servicing instructions.
WARNING
Item # Description Part Number
1 Frame 73-041-0101
2 Drain Plug 73-002-0251
3 Drain Plug Seal Ring 73-002-0400
4Fuel Filter Assembly 73-003-0101
5 Fuel Filter Joint 73-003-1000
6Fuel Tank 73-002-0101
7 Axle 73-041-0351
8 Cotter Pin 73-041-0302
9 Flat Gasket 73-041-0303
10 Wheel 73-041-0301
11 Wheel Screw 73-041-0304
12 Ignitor Bracket 73-052-1001
13 PCB Bracket 73-027-1001
14 PCB 73-027-1000
15 Fuel Cap Gasket 73-006-0110
16 Fuel Cap 73-006-0101
17 PCB 2 73-027-0200
18 Power Switch 73-038-0101
19 Thermo Cut-Off Adjusting Screw 73-019-1002
20 Knob 73-028-0500
21 Display Window 73-028-0400
22 Control Panel 73-028-0301
23 Bracket 73-041-0111
24 Fuel Gauge 73-002-1000
25 Ignitor 73-052-1000
26 Front Support 73-041-0112
27 Bottom Shell 73-001-0201
28 Air Outlet 73-001-0351
29 Ceramic Fiber Bracket 73-010-1100
30 Ceramic Fiber Fixed Support 73-010-1200
31 Ceramic ber 73-010-1000
32 Upper Front Shell 73-001-0101
33 Shell Support Ring 73-001-1000

NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2014, Pinnacle Products International, Inc. Indirect Fired Heater User’s Manual
®
19
Parts List - 170T-IDF
Item # Description Part Number
34 Combustion Chamber 73-010-0101
35 Exhaust Hood / Flue Collar 73-010-0151
36 Upper Back Shell 73-001-0301
37 Photocell Assembly Bracket 73-016-1000
38 Photocell Assembly 73-016-0101
39 Thermo Cut-Off Bracket 73-019-1001
40 Thermo Cut-Off 73-019-1000
41 Left Wind Shield 73-015-1100
42 Right Wind Shield 73-015-1000
43 Nozzle Assembly 73-015-0101
44 Ignition Needle 73-015-3000
45 Nozzle Connector 73-015-2000
46 Nozzle Base 73-015-2100
47 Oil Filter 73-003-0130
48 Oil Filter Connector 73-003-1000
49 Nozzle Base Plate 73-015-2200
50 Side Plate 73-015-1200
51 M16 Screw Nut 73-015-4000
52 Oil Filter Support 73-003-1100
53 Copper Bend Connector 73-015-5300
54 Copper Pipe 73-015-5200
55 Pipe Fix Nut 73-015-5100
56 Pipe Fix Ring 73-015-5000
57 Fan 73-024-0101
58 Pump 73-020-0151
59 Shrapnel Nut 73-016-2000
60 Rear Guard 73-016-0051
61 Fuel Filter Joint 2 73-003-2000
62 Sleeve 73-020-2000
63 Motor 73-020-0101
64 Motor Support 73-020-0102
65 Solenoid Valve 73-035-0301
66 Back Frame 73-041-0102
67 Cord Holder 73-041-0103
68 Power Cord 73-034-0100
69 Lock 73-003-1200
70 Oil Pipe 300 mm 73-003-0302
71 Oil Pipe 350 mm 73-003-0301
72 Oil Pipe 400 mm 73-003-0300
73 Back Support 73-041-0113