Pioneer Super Tuner IIID AVIC-F700BT User manual

PI~nf9f9r sound. vision. soul
INSTALLATION MANUAL
MANUEL D'INSTALLATION
m
:::3
co
-
en'
J
FLASH MEMORY MULTIMEDIA AV NAVIGATION
RECEIVER
RECEPTEUR
AV MULTIMEDIA AMEMOIRE FLASH
AVEC SYSTEME DE NAVIGATION
AVIC-F900BT
AVIC-F700BT
AVIC-F7010BT

• (Contents
)
(----~)
~ IMPORTANT INFORMATION
ABOUT YOUR NEW NAVIGATION SYSTEM
AND THIS MANUAL 3
~ IMPORTANT SAFEGUARDS
PLEASE READ ALL OF TH ESE
INSTRUCTIONS REGARDING YOUR
NAVIGATION SYSTEM AND RETAIN THEM
FOR FUTURE REFERENCE 4
~ Connecting the System
Precautions before connecting the
system 5
Before installing
this product 6
To prevent damage 6
-Notice for the blue lead 6
-Notice for the blue/white lead 7
Parts supplied 7
Connecting the system 8
Connecting the power cord
(1) 10
Connecting the power cord (2) 12
When connecting to separately sold power
amp 14
When connecting arear view camera 16
When connecting the rear display 17
-When using arear display connected to
rear video
output 17
When connecting the external video
component 17
-Using "AV1 Input" (AV1) 17
-Using "AV2 Input" (AV2) 18
When connecting the external unit featuring
video source
19
~ Installation
Precautions before installation 20
To guard against electromagnetic
interference 20
Before installing 21
m En
Installing this navigation system 21
-Installation notes 21
-Parts supplied 22
-Installation using the screw holes on
the side of the navigation unit
22
Installing the GPS antenna 23
- Installation notes 23
-Parts supplied 23
-When installing the antenna inside the
vehicle (on the rear shelf) 24
-When installing the antenna outside
the vehicle (on
the body) 25
Installing the microphone 26
-Parts supplied 26
- Mounting on the sun visor 26
-Installation on the steering column 27
Adjusting the microphone angle 27
G> After Installation
After Installing this Navigation System 28

Section
[
_IM_PO_R_l_'A_NT ~J [ ~J 01 .. '
iNFORMATION . _ .
ABOUT YOUR NEW
NAVIGATION SYSTEM AND
THIS MANUAL
• The navigation features of this product
(and rear view camera option if purchased)
are intended solely to aid
you in the opera-
tion of your vehicle.
It is not asubstitute for
your attentiveness, judgment and care
when driving.
•Never use this navigation system to route
to hospitals, police stations, or similar facil-
ities
in an emergency. Please call the ap-
propriate emergency number.
•
Do not operate this navigation system (or
the rear view camera option if purchased) if
doing
so in any way will divert your atten-
tion from the safe operation of your vehicle.
Traffic restrictions and advisories currently
in force should always take precedence
over guidance given
by this product. Al-
ways obey'current traffic restrictions,
even
if this product provides contrary advice.
•This manual explains how to install this
na-
vigation system in your vehicle. Operation
of this navigation system
is explained in
the separate manuals for the navigation
system.
•
Do not install this product where it may (i)
obstruct the driver's vision, (ii) impairthe
performance of any of the vehicle's operat-
ing systems of safety features, including
airbags, hazard lamp buttons or (iii) impair
the driver's ability to safely operate the vehi-
cle.
In some cases, it may not be possible
to install this product because of the vehi-
cle type orthe shape of the vehicle inter-
ior. (!]
m
::::s
CC
-
(ii'
::::s'
En m

section
m (IMPORTANT J ( J
~_ S_A_F_EG_U_A_R_D_S ~ ~ ~
PLEASE READ ALL OF THESE
INSTRUCTIONS REGARDING
YOUR
NAVIGATION SYSTEM
AND RETAIN THEM FOR
FUTURE REFERENCE
Read this manual fully and carefully before in-
stalling your navigation system.
2Keep this manual handy for future reference.
3
Pay close attention to all warnings in this
manual and follow the instructions carefully.
4This navigation system may in certain circum-
stances display erroneous information regard-
ing the position of your vehicle, the distance
of objects shown on the screen, and compass
directions.
In addition, the system has certain
limitations, including the inability to identify
one-way streets, temporary traffic restrictions .
and potentially unsafe driving areas. Please
exercise your own
judgment in the light of ac-
tual driving conditions.
5As with any accessory in your vehicle's inter-
ior, the navigation system should not divert
your attention from the safe operation of your
vehicle.
If you experience difficulty in operat-
ing the system or reading the display, please
make adjustments while safely parked.
6Please remember to wear your seat belt at all
times while operating your vehicle.
If you are
ever
in an accident, your injuries can be con-
siderably more severe if your seat belt
is not
properly buckled.
7Certain government laws may restrict the pla-
cement and use of navigation systems in your
vehicle. Please comply with all applicable
laws and regulations
in the installation and
operation of your navigation system.
&WARNING
Do not attempt to install or service your naviga-
tion system
by yourself. Installation or servicing
of the navigation system
by persons without train-
ing and experience in electronic equipment and
(I) En
automotive accessories may be dangerous and
could expose you to the risk of electric shock or
other hazards.
C!J

(Connecting the System)
Section
(~ )m
Precautions before
connecting
the system
&WARNING
Pioneer does not recommend that you install
your navigation system yourself.
We recom-
mend that
only authorized Pioneer service
personnel, who have special training and ex-
perience in mobile electronics, set up and in-
stall
this product. NEVER SERVICE THIS
PRODUCT YOURSELF. Installing or servi-
cing this product and its connecting cables
may expose you to the risk of electric shock
or other hazards, and can cause damage
to
the navigation system that is not covered by
warranty.
4CAUTION
• If you decide to perform the installation
yourself, and have special training and ex-
perience in the mobile electronics instal-
lations, please carefully
follow all of the
steps in the installation manual.
•Secure all
wiring with cable clamps or
electrical tape. Do not
allow any bare wir-
ing to remain exposed.
•Do not
directly connect the yellow lead of
this product to the vehicle battery. If the
lead is
directly connected to the battery,
engine vibration may eventually cause
the insulation
to fail at the point where
the wire passes from the passenger com-
partment
into the engine compartment. If
the yellow lead's insulation tears as a re-
sult of contact with metal parts, short-cir-
cuiting can occur, resulting in
considerable danger.
•
It is extremely dangerous to allow the
cables
to become wound around the steer-
ing column or
shift lever. Be sure to install
this product, its cables, and wiring away
in such a
way that they will not obstruct
or hinder driving.
•Make sure
that the cables and wires are
routed and secured so
they will not inter-
fere
with or become caught in any of the
vehicle's moving parts, especiallythe
steering wheel,
shift lever, parking brake,
sliding seat tracks, doors, or any
of the ve-
hicle's controls.
•Do not route wires where
they will be ex-
posed
to high temperatures. If the insula-
tion heats up, wires
may become
damaged, resulting in ashort circuit or
malfunction and permanent damage
to
the product.
•Do not cut the GPS antennacable
to
shorten it or use an extension to make it
longer. Altering the antenna cable could
result in ashort
circuit or malfunction.
•Do not shorten
any leads. If you do, the
protection circuit (fuse holder, fuse resis-
tor or filter, etc.)
may fail to work properly.
•Never feed power
to other electronic pro-
ducts
by cutting the insulation of the
power supply lead
of the navigation sys-
tem and tapping
into the lead. The current
capacity
of the lead will be exceeded,
causing overheating.
•The black lead is ground. Please ground
this lead separately from the ground of
high-current products such as power
amps. Do not ground more than one pro-
duct together
with the ground from an-
other product. For example, you
must
separately ground any amp unit away
from the ground
of this navigation sys-
tem. Connecting grounds togethercan
cause afire and/or damage the products
if
their grounds became detached.[!)
..
m
j
(,Q
iii"
:::r
En CD

Section
18(Connecting the System)
(~----~)
Before installing this
product
•This product is for vehicles with a12-volt
battery and negative grounding, Check the
battery voltage of your vehicle before instal-
lation.
•
To avoid shorts in the electrical system, be
sure to disconnect the (-) battery cable be-
fore beginning installation.
•
To avoid short-circuiting, cover the discon-
nected lead with insulating tape. It is espe-
cially important to insulate all unused
speaker leads. which if left uncovered may
cause ashort circuit.
•Attach the connectors of the same color to
the corresponding colored port, i,e., blue
connector to the blue port, black to black,
etc.
•Refer to the owner's manual for details on
connecting the power amp and other units,
then make connections accordingly,
•Since aunique
BPTL circuit is employed,
do not directly ground the eside of the
speaker lead
or connect the esides of the
speaker leads together,
Be sure to connect
the eside of the speaker lead to the e
side of the speaker lead on this navigation
system.
•
If the RCA pin jack on this product will not
be used, do not remove the caps attached
to the end of the connector.
•Never connect speakers with an output rat-
ing of less than
50 Wchannel or impe-
dance outside of the 4ohms to 8ohms
specifications to your navigation system.
Connecting speakers with output and/or
impedance values other than those noted
here may result in the speakers catching
fire, emitting smoke, or becoming
da-
maged.
Notice for the blue lead
• A signal is output through the blue lead to
control the antenna of your vehicle.
The
timing varies depending on the setting. (For
more detailed information on changing
[Ant CTRL] mode, refer to "Operation Man-
ual".)
•When [Ant
CTRL] mode is set to [Radio],
the vehicle's antenna can be stowed or
turned off by following the instructions
below.
No ACC position
ACC position
To prevent damage
AWARNING
•When replacing the fuse, be sure to only
use afuse of the rating prescribed
on the
fuse holder.
•When disconnecting aconnector, pull the
connector itself.
Do not pull the lead. as
you may pull it out of the connector.
•This product cannot
be installed in a vehi-
cle without ACC (accessory) position on
the ignition switch.
m En

(Connecting the System)
section
(~ )a
Parts supplied
Parts marked (*) are not supplied with AVIC-
F700BT and AVIC-F7010BT.
-m
~
CO
-
iii"
:r
Power cord
The navigation unit
-Change the source from radio (AM or
FM) to another source.
-
Turn the source off
-
Turn off the ignition switch (ACC OFF)
•If [Ant CTRL] mode is set to [Power], the
vehicle's antenna can
be stowed or turned
off only when the ignition switch is turned
off
(ACC OFF).
• Do not connect this lead to the system con-
trol terminal of external power amps.
•
Be sure not to use this lead as the power
supply lead for the auto-antenna or anten-
na booster. Such connection could cause
excessive current drain and malfunction.
Notice for the bluelwhite lead
•When the ignition switch is turned on (ACC
ON), acontrol signal is output through the
blue/white lead. Connect to
an external
power amp's system remote control term-
inal (max.
300 mA 12 V DC). The control sig-
nal
is output through the blue/white lead,
even if the audio source is switched off.
•
Do not connect this lead to the auto-anten-
na relay control terminal orthe antenna
booster power control terminal.
•
Be sure not to use this lead as the power
supply lead for the external power amps.
Such connection could cause excessive
current drain and malfunction.
C!J
Connector*
Extension lead*
(for speed signal)
RCA connector
Extension lead
(for reverse signal)
GPS antenna
Microphone
En m

Section
I» (Connecting the System )
(~---~)
Connecting the system
Blue
Light gray
.-:::::::5 m (16 ft. 5in.)( ( _
);-
XM tuner (e.g. GEX-P920XM)
(sold separately)
Black
Antenna
jack
~
Vehicle antenna
'----- WIRED REMOTE INPUT
Please
see the Instruction
Manual for the Wired Remote
Control Adapters (sold separately).
......... IP-BUS cable
(supplied with hide-away
XM tuner)
*1
-When connecting your iPod. both connections are necessary.
-It is necessary to set
[AV1 Input] in [AV settings] to [iPod]
when connecting the iPod.
(For details, refer to "Operation
Manual".)
"'"- L.;o",..4_m ....... (1_3_ft_. 1_i_n.....,.) (( _
~- jr
*1
v2m (6 ft. 7 in.)
USB connector
Connect either the interface cable for
iPod
or an appropriate USB storage device.
*1
~------------~---f,,-~-[ji::_-----
, J
CD En

(Connecting the System )Section
(~ ~)GJ
-m
j
CC
-
(ii'
~
/Microphone
---------.
GPS antenna
DIGITAL OUT
This terminal is intended to support future
equipment and should not
be used if you are
using this product by itself.
AWARNING
.To avoid the risk of accident and the potential
violation
of applicable laws, this product should
never
be used while the vehicle is being driven
except for navigation purposes. Also Rear
Displays should not
be in alocation where it is
avisible distraction to the driver.
.In some countries or states, the viewing of
images on adisplay inside avehicle even by
persons otherthan the driver may
be illegal.
Where such regulations apply they must be
obeyed and this product·svideo source should
not
be used.
•Note
The XM tuner, HD-Radio tuner and SIRIUS satellite
radio tuner will not receive their service when
you
drive outside of their coverage area.
'"
SiriusConnect Cable
(sold separately)
•Note
For details concerning
operations and compatiblity,
refer to "Operation Manual".
·Sjri~sCOf)n~ctupiversal.tuner"
or "SIRIUS Dockand pjayradio
with SiriusConnectvehicle
kit"
(sold separately)
/iPOd®
~
Dock USB Interface Cable for iPod®
connector - (
port
(CD-IU230V) (sold separately)
Blue
En
CD

Section
liD ( Conneding the System)
c )
Conneding the powercord (1)
Yellow
To terminal always supplied with power
regardless of ignition switch position.
Red
To electric terminal controlled by ignition
switch
(12 V DC) ON/OFF.
Orange/White
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
----------------------------------
With a 2 speaker system, do not connect anything to
the speaker leads that
are not connected to speakers.
Right
.•
..•.••• ~. (f)' ... Rear speake. ror
. •e Subwoofer (4 0)
Violet
Gray/Black
Viotetl8lac:k .
- - - - - - - - - - - - - - - - - - - -I
Gray 1
----......;. ~ Front speaker :
~ I
I
I
I
I
I
1
I
I
Green
Green/Slack
M-C
+
Front speaker 8White/Black
aNote
When asubwoofer is connected to this navigation
system instead of arear speaker, change the rear
output setting
in the Initial Setting. (Refer to
"Operation Manual".)
The subwoofer output of this
navigation system is monaural.
r-------------------
White
Not used.
When using asubwoofer of 70 W (2 0), be sure to connect with violet and violet/black leads of this
navigation system.
Do not connect anything with green and green/black leads.
Green,/,f ...•... v_
Gr~nI8'aCk Violet/Black
En

(Connecting the System )
section
(~ ~)G1
-m
::s
CC
-
iir
:::T
L..26 cm (10-1/4 in.)
Power cord
~ ~RCA connector
~ Yellow/Black
If you use equipment with amute
function, connect that equipment to
the Audio Mute lead. If not.
keep the
Audio Mute lead free of any
connections.
•Note
Audio source will be set to mute or attenuate, while the following
sounds will not
be muted or attenuated. For details, see
"Operation Manual".
- voice guidance of the navigation
-incoming Ringtone and incoming
voice of the cellular phone
that
is connected to thiS navigation system via Bluetooth
wireless technology
•Note
The antenna will automatically retract or turn off. yet the timing
varies depending
on the setting.
Blue
To auto-antenna relay control tel'mrnal.
If the vehicle has aglass antenna. connect to the antenna
booster power control terminal
(max. 300 mA 12 V DC).
F-!'·l
En

section
m(Connecting the System )
(-----~)
Connecting the power cord (2)
"3 m (9 ft. 10 in.)
IINote
The position of the speed detection circuit and the position of the
parking brake switch vary depending on the vehicle model.
For details.
consult your authorised Pioneer dealer or an installation professional.
&WARNING
IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE
OR INJURY INCLUDING ELECTRICAL SHOCK, AND
INTERFERENCE WITH THE OPERATION OF THE VEHICLE'S
ANTI LOCK BRAKING SYSTEM. AUTOMATIC TRANSMISSION
AND SPEEDOMETER INDICATION.
4CAUTION
It is strongly suggested that the speed pulse wire be connected for
accuracy of navigation and better performance.
Pink (CAR SPEED SIGNAL INPUT)
This connection is unnecessary for AVIC-F700BT and AVIC-F701 OBT.
The mobile navigation system is connected here to detect the distance the
vehicle travels. Always connect the
vehicle's speed detection circuit. Failure
to make this connection will increase errors
in the location display.
...
Clamp firmly
with needle-
nosed pliers.
Close the cover.
Connection method
Pass the extension
~ cord and the lead for
~ the speed detection
J. circuit through this
hole.
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
l ~ _
Parking brake switch
Power supply Side
Ground side
Clamp the parking brake switch
power supply side lead.
...
Clamp firmly with needle-nosed
pliers.
Connection method
Light green
Used to detect the ON/OFF status of the parking brake. This lead must be
connected to the power supply side of the parking brake switch.
If this connection is made incorrectly or omitted, certain functions
A of your navigation system will be unusable. ~
"WARNING --------------,
LIGHT GREEN LEAD AT POWER CONNECTOR IS
DESIGNED TO DETECT PARKED STATUS AND MUST Ir---"""'"'-------------
BE CONNECTED TO THE POWER SUPPLY SIDE OF THE
PARKING BRAKE SWITCH. IMPROPER CONNECTION
OR USE OF THIS LEAD MAY VIOLATE APPLICABLE
LAW AND MAY RESULT IN SERIOUS INJURY OR
DAMAGE.
En

(Connecting the System )Section
(~ ~)a
-m
::3
co
-
iii'
J
~-.Icn:;an--_
"\Extension lead
(for speed
sig~al)
The navigation unit
g.J
!ower cord
I /This connection is unnecessary for ~
rAVICF700BT and AVIC·F701 OBT.
L _
Violet/white (REVERSEGEAR SIGNAL INPUT)
This is connected so that the navigation system can detect
whether the vehicle
is moving forwards or backwards.
.Connect the violet/white lead to the lead whose voltage
changes when the shift lever
is put in reverse. Unless
connected, the sensor may not detect your vehicle
travelling forward/backward properly, and thus the position
of your vehicle detected
by the sensor may be misaligned
from the actual position.
••
Clamp firmly with
needle-nosed
pliers.
Clamp the backup
light lead. -
Connection method
""
5m (16 ft. 5in.)
ACAUTION
Be sure to use only the supplied extension lead. Use of another
lead could cause fire. smoke
and/or damage this navigation
system. I
Fuse resistor
_Note
When you use arear view camera, please make
sure to connect this lead. Otherwise
you cannot
switch to rear view camera picture.
""
Extension lead
(for reverse signal)
~ _ _ Check the position of your vehicle's ~~
I------=:::::___ J.;-;-- backup light (the one that lights up ..!:-. ~
~ Gwhen the shift lever is in reverse [R)) ~~
~
0and find the backup light lead in the
I': trunk.
!:> /
En

SectIon
liD (Connecting the System)
('------~)
When connecting to separately sold poweramp
~ RCA connector
The navigation unit
Subwoofer output
(SUBWOOFER OUTPUn
28cm
(11 in.) •
Rear output
(REAR OUTPUT)
30cm (11-7/8
in.)
•
Front output
(FRONT OUTPUn
30cm (11-7/8 in.)
~ <:JI-------
~ <:Jl---------
~ <:JI--------
30cm (11-7/8 in.)
Blue/white
To system control terminal of the power amp
(max.
300 mA 12 V DC) .
• Note
You can change the RCA output of the subwoofer depending on your subwoofel'
system. (Refer to "Operation Manual".)
® En

(Connecting the System)
Section
(~ ~)a
..
m
::s
cc
-
iii"
:r
------~----------4c::: ~
Power amp
(sold separately)
Power
amp
(soldseparately)
Power
amp
(sold separately)
--------I.--.....-tc::: ~
'-----...,._ ....
RCA cables
(sold separately)
--------~-;.-----c:;;,--.~~
----~
~~I"--r@J_OO __
~,,"----------
System remote control
Left
Front speaker
Rearspeaker
Right
Front speaker
Rearspeaker
Subwoofer Subwoofer
En ill)

Fuse resistor
Section
aD (Connecting the System)
When connecting arear view
camera
When this product is used with arear view
camera, it is possible to
automatically switch
from the video to rear view image when the
gear shift is moved to REVERSE (R), Rear-
View mode also allows you to check what is
behind you
while driving.
AWARNING
USE INPUT ONLY FOR REVERSE OR MIRROR
IMAGE REAR VIEW CAMERA. OTHER USE MAY
RESULT IN INJURY OR DAMAGE.
A CAUTION
• The screen image may appear reversed.
•The rear view camera function
is to use this
product
as an aid to keep an eye on trailers, or
backing into atight parking spot.
Do not use
this function for entertainment purposes.
•
The object in rear view may appear closer or
more distant than in reality.
•Please note that the edges of the rear view
camera images may differ slightly according
to whether full screen images are displayed
when backing, and whether the images are
used for checking the rear when the vehicle is
moving forward.
A CAUTION
Be sure to use only the supplied extension
lead. Use of another lead could cause fire,
smoke and/or damage this navigation sys-
tem.
® En
(-----~)
Rear view camera
(e,g. ND·BC2)
1-------- .....
(sold separately)
Violet/white
~
~
Power cord
'\
5m
(16 ft. 5in,) The navigation unit
'\. Extension lead (for reverse signal)
For more details about the wiring, refer to Connecting
the power cord
(2) on page 12
•Notes
•It is necessary to set [Back Camera] in
[System Settings] to [On] when connect·
ing the rear view camera.
(For details, refer
to "Operation Manual",)
•Connect to the rear view camera, Do not
connect to any otherequipment.

(Connecting the System)
Sectior
(~ )G
When connecting the rear
display
This connection is unnecessary for AVIC-
F700BTand AVIC-F701
OBT.
When connecting the
external video component
Using IAV1lnput" (AV1)
The navigation unit
~RCAcables
~ 0' (sold sepacately)
~ 'TO audiO outputs
t t t
To video output
:~~~
?;~?~<QJ
• A20cmI7.7I8In)
RCA connector fi
.A ~ Red, white
Yellow
~ I~ II!!, (AUDIO INPUn
(VIDEO INPUn
Rear display with
RCA input jacks
The navigation unit
When using arear display
connected
to rear video output
AWARNING
NEVER install the rear display in alocation
that enables the driver to watch the video
source while driving.
This navigation system's rear video output is for
connection of adisplay to enable passengers in
the rear seats to watch the video source.
C!J
External video
component
(sold separately)
•It is necessary to set [AV1 Input] in [AV
Settings] to [Video] when connecting the
external video component. (For details,
refer to "Operation
Manual".)
En ®

Section
D (Connecting the System)
(~-----)
Using" AV2 Input" (AV2) 4CAUTION
Be sure to use aCD-RM10 (sold separately) for
wiring. If
you use other cables, there is acase
where wiring position differs, images and sounds
may
be disturbed.
L: Left audio (White)
R: Right audio
(Red)
V: Video (Yellow)
G: Ground
OK
(S)
~L ~L
V G R R G V
Red, white
To audio outputs
Mini jack
To video output
7
CD-RMlO
(sold separately)
The navigation unit
External video
component
(sold separately)
•It is necessary to set [AV2 Input] in [AV
Settings]
to [Video] when connecting the
external video component. (For details,
refer to "Operation Manual",)
® En

(Connecting the System)
When connecting the
external unitfeaturing video
source
The navigation unit
sectiol
(~ ~)G
m
:s
CQ
-
iii"
~
"
Ii
RCA cable
(sold separately)
~
Blue
Black
•It is necessary to set [AV1 Input] in [AV
Settings] to [EXT] when connecting the ex-
ternal unit. (For details, refer to "Operation
Manual".)
[!J
En @

Section
D (Installation )
(~-----)
Precautions before
installation
&WARNING
Pioneer does not recommend that you install
or service your navigation system yourself.
Installing or servicing the product may ex-
pose you
to risk of electric shock or other ha-
zards. Refer
all installation and servicing of
your navigation system to authorized
Pioneer service personnel.
ACAUTION
•Never install this product in places where,
or in a manner that:
- It could injure the driver or passengers
if the vehicle stops suddenly.
-
It may interfere with the driver's opera-
tion of the vehicle, such as on the floor
in front of the driver's seat, or close to
the steering wheel or shift lever.
•
Make sure there is nothing behind the
dashboard or paneling when drilling holes
in them. Be careful not to damage fuel
lines,
brake lines, electronic components,
communication wires or power cables.
•When
using screws, do not allow them to
come into contact with any electrical lead.
Vibration may damage wires or insulation,
leading to a short circuit or other damage
to the vehicle.
•To ensure
proper installation, use the sup-
plied parts in the manner specified. If any
parts other than the supplied ones are
used,
they may damage internal parts of
this product or they may work loose and
the product may become detached.
• It is extremely dangerous to allow the
cables to become wound around the steer-
ing column or shift lever. Be sure to install
this product, its cables, and wiring away
in such a way that they will not obstruct
or hinder driving.
00 En
• Make sure that leads cannot get caught in
a door or the sliding mechanism of aseat,
resulting in a short circuit.
•Please confirm the proper function of
your vehicle's other equipment following
installation of the navigation system.
•Certain
government laws may prohibit or
restrict the placement and use of this sys-
tem in your vehicle. Please comply with
all applicable laws and regulations re-
garding the use, installation and operation
of your navigation system.
•
Do not install this navigation system
where it may (i) obstruct the driver's vi-
sion, (ii) impair the performance of any of
the vehicle's operating systems or safety
features, including airbags, hazard lamp
buttons or (iii) impair the driver's ability
to safely operate the vehicle.
•
Install the navigation system between the
driver's seat and front passenger seat so
that it will not be hit by the driver or pas-
senger
if the vehicle stops quickly.
•Never install the navigation system in
front of or next to the place in the dash,
door,
or pillar from which one of your vehi-
cle's airbags would deploy. Please refer to
your vehicle's owner's manual for refer-
ence
to the deployment area of the frontal
airbags.
•Do
not install the navigation system in a
place
where it will impair the performance
of any of the vehicle's operating systems,
including airbags and headrests.0
To guard against
electromagnetic interference
In order to prevent interference. set the follow-
ing items
as far as possible from this naviga-
tion system, other cables or leads:
•
TV antenna and antenna lead
•
FM, AM antenna and its lead