Pioneer DVH-860AV/XEUW5 User manual

ORDER NO.
PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2013
DVH-860AV/XEUW5
CRT5452
DVD AV RECEIVER
DVH-860AV /XEUW5
DVH-865AVBT/XERD
DVH-865AVBT/XERI
DVH-8680AVBT/XFBR
K-ZZZ DEC. 2013 Printed in Japan

DVH-860AV/XEUW5
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safety repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safety, you should not risk trying to do so
and refer the repair to a qualified service technician.
This product is a class 1 laser product, but
this product contains a laser diode higher
than Class 1. To ensure continued safety,
do not remove any covers or attempt to
gain access to the inside of the product.
CAUTION: USE OF CONTROLS OR
ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
CAUTION: THE USE OF OPTICAL
INSTRUMENTS WITH THIS PRODUCT
WILL INCREASE EYE HAZARD.
-Safety Precautions for those who Service this Unit.
When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacture.
Discord used batteries according to the manufacture's instructions.
WARNING!
The AEL (accessible emission level) of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.
Laser diode characteristics
Wave length:
DVD:650 nm to 662 nm
CD:775 nm to 795 nm
Focus lens on Maximum output:
CD:2.18 mW
DVD:1.33 mW
Additional Laser Caution
Transistors Q1 and Q2 in PCB drive the laser diodes for DVD and CD
respectively. When Q1 or Q2 is shorted between their terminals,
the laser diodes for DVD or CD will radiate beam. If the top cover is removed
with no disc loaded while such short-circuit is continued, the naked eyes may
be exposed to the laser beam.

DVH-860AV/XEUW5 3
5 678
5678
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION .....................................................................................................................................2
1. SERVICE PRECAUTIONS................................................................................................................................4
1.1 SERVICE PRECAUTIONS .........................................................................................................................4
1.2 NOTES ON SOLDERING...........................................................................................................................5
2. SPECIFICATIONS.............................................................................................................................................6
2.1 SPECIFICATIONS ......................................................................................................................................6
2.2 DISC/CONTENT FORMAT.........................................................................................................................9
3. BASIC ITEMS FOR SERVICE ..........................................................................................................................9
3.1 CHECK POINTS AFTER SERVICING .......................................................................................................9
3.2 PCB LOCATIONS.....................................................................................................................................10
3.3 JIGS LIST ................................................................................................................................................. 11
3.4 CLEANING ............................................................................................................................................... 11
3.5 FACTORY SETTINGS.............................................................................................................................. 11
4. BLOCK DIAGRAM ..........................................................................................................................................12
4.1 OVERALL CONNECTION DIAGRAM ......................................................................................................12
4.2 BLOCK DIAGRAM....................................................................................................................................13
4.3 POWER BLOCK DIAGRAM .....................................................................................................................14
5. DIAGNOSIS ....................................................................................................................................................16
5.1 OPERATIONAL FLOWCHART.................................................................................................................16
5.2 ERROR CODE LIST.................................................................................................................................17
5.3 CONNECTOR FUNCTION DESCRIPTION .............................................................................................18
6. SERVICE MODE.............................................................................................................................................19
6.1 SOFTWARE VERSION INFORMATION DISPLAY ..................................................................................19
6.2 SOFTWARE VERSION UP METHOD......................................................................................................20
7. DISASSEMBLY ...............................................................................................................................................25
8. EACH SETTING AND ADJUSTMENT............................................................................................................31
9. EXPLODED VIEWS AND PARTS LIST ..........................................................................................................32
9.1 PACKING..................................................................................................................................................32
9.2 EXTERIOR (1) (XEUW5, XERD, XERI) ...................................................................................................34
9.3 EXTERIOR (1) (XFBR).............................................................................................................................36
9.4 EXTERIOR (2) (XEUW5, XERD, XERI) ...................................................................................................38
9.5 EXTERIOR (2) (XFBR).............................................................................................................................40
10. SCHEMATIC DIAGRAM................................................................................................................................42
10.1 MB ASSY (MCU_RADIO PART) (GUIDE PAGE) ...................................................................................42
10.2 MB ASSY (BT_AMP PART) (GUIDE PAGE) ..........................................................................................48
10.3 SB ASSY (POWER PART) .....................................................................................................................54
10.4 SB ASSY (MAIN PART)..........................................................................................................................56
10.5 SB ASSY (FLASH&SDRAM PART)........................................................................................................58
10.6 KB PCB and AUX PCB...........................................................................................................................60
10.7 CB ASSY and LB ASSY .........................................................................................................................62
11. PCB CONNECTION DIAGRAM ....................................................................................................................64
11.1 MB ASSY ................................................................................................................................................64
11.2 SB ASSY.................................................................................................................................................68
11.3 KB PCB...................................................................................................................................................70
11.4 AUX PCB ................................................................................................................................................72
11.5 CB ASSY ................................................................................................................................................73
11.6 LB ASSY .................................................................................................................................................74
12. ELECTRICAL PARTS LIST...........................................................................................................................75

DVH-860AV/XEUW5
4
1234
1234
C
D
F
A
B
E
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
1. You should conform to the regulations govering the product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following the safety instructions described in this manual.
2. Be careful about an internal sharp edge.
3. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by
electrostatic induction.
4. Be careful in handing made from metal parts. There might be burr at the edge of it.
5. DEMO MODE is activated by Default Setting.
Keys other than followings are not accepted under DEMO MODE operation.
[SRC], [ESC] and [POWER] (However, POWER being OFF in case of POWER Key.)
Conduct performance confirmation after releasing DEMO MODE operation temporarily.
How to perform temporary releasing
DEMO operation is released temporarily with [SRC] or [ESC] Key on Main Body Key (or on Remote Controller) and
normal operation becomes possible.
How to make DEMO MODE to be OFF (There are two ways, (1) and (2))
DEMO MODE under operation
(1) Turn ACC from OFF to ON. This makes DEMO setting to be OFF.
(2) Temporarily release DEMO MODE (by pressing [SRC] or [ESC] Key) and change setting of DEMO in GENERAL
from setting menu by changing ON to OFF.
6. Two kinds of resetting are available
1) Turn over the Detach Panel and press RESET Button at Central Part.
Without entire initialization.
Microcomputer restarting (emergency resetting at function trouble) .
With the reset of the pioneer.
2) Perform [Default Setting] initialization in Setting
Perform product initialization except a part of items.
Please carry it out when updating software.
7. Any component parts in the DVD Mechanism Unit of this model can not be supplied.
If you need to replace any parts in the DVD Mechanism Unit, replace whole of DVD Mechanism Unit.
8. Graphically-illustrated areas become hot. Be careful not to burn yourself.

DVH-860AV/XEUW5 5
5 678
5678
C
D
F
A
B
E
1.2 NOTES ON SOLDERING
9. When you replace the IC, U401 on the MB, the software has to be updated to the latest one.
10. When you replace MB Assy (Main Board) on DVH-8680AVBT/XFBR, remove Q813 from the old MB Assy, and
install onto the new MB Assy.
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:
Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

DVH-860AV/XEUW5
6
1234
1234
C
D
F
A
B
E
2. SPECIFICATIONS
2.1 SPECIFICATIONS
DVH-860AV/XEUW5
Backup current ........................................ 3 mA or less

DVH-860AV/XEUW5 7
5 678
5678
C
D
F
A
B
E
DVH-865AVBT/XERD, /XERI
General
Rated power source: ............................... 14.4 V DC (allowable voltage range: 12.0 V to 14.4 V
DC)
Preout maximum output level:................. 4.0 V
Maximum current consumption: ............. 10.0 A
Dimensions (W × H × D):
Chassis............................................ 178 mm × 50 mm × 165 mm
Nose ................................................ 188 mm × 58 mm × 22 mm
Weight: .................................................... 1.4 kg
Display
Screen size/aspect ratio: ......................... 3.5 inch wide/16:9 (effective display area: 76.80 mm
× 43.20 mm)
Pixels:...................................................... 320 × (RGB) × 240
Display method: ..................................... TFT active matrix
Durable temperature range (power off) ... –20 °C to + 60 °C
DVD Player
System..................................................... DVD video, Video CD, CD,WMA, MP3, DivX, JPEG
system
Usable discs ............................................ DVD video, Video CD, CD, CD-R/RW, DVD±R/RW/
R DL
Region number........................................ 4 for Latin America models
........................................ 2 for Middle East Asian models
Frequency response................................ 20 Hz to 20 kHz (with DVD, at sampling frequency
96 kHz)
Signal-to-noise ratio................................. 75 dB (1 kHz) (IEC-A network) (RCA level)
Output level:
Video ...............................................
Number of channels ................................ 2 (stereo)
MP3 decoding format .............................. MPEG-1 & 2 Audio Layer 3
WMA decoding format............................. Ver. 7, 7.1, 8, 9, 10, 11 (2ch audio) (Windows Media
Player)
DivX decoding format .............................. Home Theater Ver. 3, 4, 5.2, 6 (.avi, .divx)
DVD video output .................................... NTSC
Audio
Maximum power output: .......................... 50 W × 4
Continuous power output ... ....................
both channels driven)
Load impedance:.....................................
Preout maximum output level
USB standard specification:.....................
.................. 4.0 V
Equalizer (3-Band Graphic Equalizer):
Frequency ....................................... 100Hz/1kHz/10kHz
Gain................................................. -14 to +14 dB
Backup current ....................................... 3 mA or less
Subwoofer (mono):
Frequency ....................................... 80 Hz/120 Hz/160 Hz
Gain................................................. -79 dB to 0 dB
USB
USB 1.1, USB 2.0 full speed
Maximum current supply ......................... 1000 mA
File system: ............................................. FAT16, FAT32
FM tuner
Frequency range: .................................... 87.5 MHz to 108.0 MHz)
Usable sensitivity..................................... 10 dBµ (S/N: 30 dB)
AM tuner
Frequency range: .................................... 531 kHz to 1 602 kHz (9 kHz)
.................................... 530 kHz to 1 640 kHz (10 kHz)
Usable sensitivity:.................................... 30 dBµ (S/N: 20 dB)
Bluetooth 2.0 certified
Bluetooth
Version ....................................................
Output power
Specifications and the design are subject to modifications without notice.
........................................... +4 dBm Maximum(Power class 2)
Note

DVH-860AV/XEUW5
8
1234
1234
C
D
F
A
B
E
DVH-8680AVBT/XEBR
Backup current ........................................... 3 mA or less

DVH-860AV/XEUW5 9
5 678
5678
C
D
F
A
B
E
2.2 DISC/CONTENT FORMAT
3. BASIC ITEMS FOR SERVICE
3.1 CHECK POINTS AFTER SERVICING
is a trademark of DVD Format/Logo Licensing Corporation.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by PIONEER CORPORATION is under license.
Other trademarks and trade names are those of their respective owners.
To keep the product quality after servicing, please confirm following check points.
No. Procedures Item to be confirmed
1 Confirm whether the customer complain has
been solved.
If the customer complain occurs with the
specific media, use it for the operation check.
The customer complain must not be
reappeared.
Display, video, audio and operations must be
normal.
2 DVD Play back a DVD.
(Menu operation; Title/chapter search)
Display, video, audio and operations must be
normal.
3 CD Play back a CD.
(Track search)
Display, audio and operations must be
normal.
4 FM/AM tuner Check FM/AM tuner action.
(Seek, Preset)
Switch band to check both FM and AM.
Display, audio and operations must be
normal.
5 Check whether no disc is inside the product. The media used for the operating check must
be ejected.
6 Appearance check No scratches or dirt on its appearance after
receiving it for service.
For check items concerning image and voice, please refer to the followings:
Check items concerning image Check items concerning voice
Block-noise Distortion
Crosscut noise Noise
Dot noise Low volume
Distorted image (Image skip) High volume
Low brightness Changes in level
Too bright Pause of sound
Color fading
Partial discoloration

DVH-860AV/XEUW5
10
1234
1234
C
D
F
A
B
E
3.2 PCB LOCATIONS
C
SB Assy
MB Assy
ECB Assy
KB Assy
DAUX PCB
A
LB Assy
F
B
Unit Number : 843DM7387ARMB003(UW5)
Unit Number : 843DM7387BLMB003(RD)
Unit Number : 843DM7387BLMB003(RI)
Unit Number : 883DM7387BBMB003(BR)
Unit Name : MB Assy
Unit Number : 842DM7387ARSB003(UW5)
Unit Number : 842DM7387BLSB003(RD)
Unit Number : 842DM7387BMSB003(RI)
Unit Number : 882DM7387BBSB003(BR)
Unit Name : SB Assy
KB Assy
Consists of
KB PCB
AUX PCB
Unit Number : 843DM7387ARKB003(UW5)
Unit Number : 843DM7387BLKB003(RD)
Unit Number : 843DM7387BLKB003(RI)
Unit Number : 883DM7387BBKB003(BR)
Unit Name : KB Assy
Unit Number : 843DM7387BMCB000(UW5,RD,RI)
Unit Number : CYW1043(BR)
Unit Name : CB Assy
Unit Number : 843DM7387BMLB001(UW5,RD,RI)
Unit Number : CYW1044(BR)
Unit Name : LB Assy

DVH-860AV/XEUW5 11
5 678
5678
C
D
F
A
B
E
3.3 JIGS LIST
3.4 CLEANING
3.5 FACTORY SETTINGS
-Jigs List
Name
21P FFC
Acetate Tape
Jig No.
GGD1627
GYH1026
Remarks
MB Assy (Mother) - SB Assy (DVD Decode)
Disassembly
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
Portions to be cleaned Cleaning tools
DVD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008
-When the Repair is Complete
When the repair is complete, make the DVD mechanism ready for transportation
implementing the following procedures:
1. Attach the two Transportation Screws.
Now you can transport it.(See the figure below)
Transportation Screws
121045000198

DVH-860AV/XEUW5
12
1234
1234
C
D
F
A
B
E
4. BLOCK DIAGRAM
4.1 OVERALL CONNECTION DIAGRAM
CKB PCB C
SB Assy
MB Assy
ECB Assy
A
LB Assy
F
B
DAUX PCB
DVD Mechanism module
(Main Board)
(Key Board)
CON202: 39pin
to TFT-LCD
CN201 : 25pin
to SB
(Servo Board)
CN6: 25pin
to MB
CN2 : 6pin
to Spindle Motor
CN8: 24pin
to Pick-up
CN402 : 34pin
to CB
USB201:
USB Connector
CON203
AUX-IN Connector
CN901: 20pin
Power Connector CN201+CN604 : 7pin
Video input/output
Camera input
MIC inpit
ANT101:
Tuner Antenna
CN404+CN501+CN902 : 8pin
Audio input
SWC
Parking sense
Reverse sense
3.5inch
TFT-LCD
Module
CN202+CN203 : 6pin
to SB
C0N406 : 6pin
to LB
CN7: 2pin
to Loarding
Motor
CN5 :2pin
to Disc sense
Switch
CN3: 5pin
to MB
(Light Board)
CN406 : 6pin
to MB
(Connector Board)
CON2: 34pin
to MB
CON1:34pin
to KB
CON201: 34pin
to CB
BT Module
NF2301
64pin

DVH-860AV/XEUW5 13
5 678
5678
C
D
F
A
B
E
4.2 BLOCK DIAGRAM
CKB PCB C
SB Assy
MB Assy
A
B
DAUX PCB
Motor
Servo system
Zoran
ZR36966H
Panel keys
LCD Driver
T118FS
T35P21
3.5“16:9 TFT
Display
L/R
FL/FR
Motor Driver
D5869S
Audio
Processor
TDA7419
Jinyuan
A/D
SPI
I2C
Power Supply
Video out
Video Switch & Drivers
D6502
I2C
Camera in
Front AV-IN
Bu+
IPOD
Appreciate
337S3959
BT Audio
Operational
AMP
TPA6112A2
UART
L/R
I2C
SD RAM
M12L64164A
FLASH ROM
MX29LV160D
BTI-70G
CVBS
LINE OUT
Front
Rear/Sub
Preamp
YD2792
(4V x 4Ch)
USB terminal
REMOTE
IR
PICK UP
Audio DAC
ET4344
Power Amplifier
PA2032A
RL/RR
Y/C
MCU
NEC uPD78F0547
Line/sub
L/R
CVBS
DVD module
KB Unit
MB Unit
SB Unit
D9V
MCU5
VDD3.3 VDD1.8
USB5
BT3.3 +3.3V +1.8V
DVD5
Switch
74HC4052
L/R
Rear AV in
4.7V
Iso Amp
D3121
BT Module
NF2301-FW4A
USB
TUNER
TEF6621
Wired
Remote
DVD Mechanism
DL-303
Only RD,
RI, BR

DVH-860AV/XEUW5
14
1234
1234
C
D
F
A
B
E
4.3 POWER BLOCK DIAGRAM
U903
U402 U401
U103
U6
U501
U9
U3
U1 U5
U8
U4
U2
U11
U700
U703
U802 U804 U701
U201
U101
U809 U301
U904
U905
U906
P.AMP
PA2032A MCU
UPD78F0547AGK
60mA
LM2950-5V
MUTE
B+
Power Amplifier
& Antenna control
LOD 9V 1A
LSP9801
ADJ
MAX:500mA
Motor driver
D5869S
SB Assy
(MPEG_BOARD)
AP1507-ADJ
B+
LM2950-5V
Current
Term 1.5A
AP2191D MAX:1.5A
9V
5V
9V
MCU5V
D9V
DVD_5V
DVD
Power
BT_3V3
ACC or X (LED_OFF_DET)
LED_5V
D5V
DVD_5V
5V
LB Assy
(LED-Board)
K5V K5V
D5V USB:3.3V
for D+/D-
USB_CTL
Power On
BATT
+14.4V
SA1117-
3V3 BT Module
NF2301 MAX:150mA
BT Audio
Operational AMP
TPA6112A2
Audio DAC
ET4344
Loarding Motor
D9V A+9V
K5V
4.7V
+5V
DVD
Power
MAX:390mA
DVD DSP
Zoran
ZR36966H
+1.8V
Authentication
341S2162-TBB
M+5V
Ope-Amp
UTC4558
+4.5VA
EEPROM
S24C16
+3.3V
20 mA
Audio 74HCT4052DB
Audio EQ Processor TDA7419
AM FM PLL TUNER TEF6621 150mA
Audio ISO D3132
Audio Preamp YD2792
47 mA
5V
220R
100R + 10K
2R2
100R
10R
200R
10R
Video selector & Driver
D6502
MAX:100mA
50R
1.1R
W-LED
W_LED
CB Assy
(Connector-Board)
RESET
2R2_1W
EEPROM
FT24C02A
D7035 Low_Check
Current Term 5V
1.5A
AP2191D
DC/DC
ACP2809
SD RAM
M12L64164A-7TG
FLASH
MX29LV160DBTI-70G
ABCD
Only RD, RI, BR

DVH-860AV/XEUW5 15
5 678
5678
C
D
F
A
B
E
U201
U202
U203
U204
REM201
U803
U403
KB PCB
(TFT-Board)
SA1117
-3V3
TFT Driver
T118FS
MAX:120mA
MAX:200mA
USB Power
Key illumination
RED or BLUE
SA1117
- 1V8
1A
LOD 9V 1A
LSP9801
ADJ
Current Term
5V 1.5A
AP2191D
USB_5V USB_Power
TFT_5V
+5V_M
VDD1.8
VDD3.3
DVD_5V
AP1507-ADJ
LAMP_SW LAMP
LIGHT
BACK_LIGHT_SW
DC/DC
AP34063
LED+
LCD
RED
BLUE
TFT_5V
+5V_TFT
VCC5V
4.88V
COCOLORE
10R
IR Receiver
Rotary Encoder
MAX:1A
AP1507-ADJ MAX:3A
SA1117-3V3 MAX:800mA
SA1117 1V8 MAX:800mA
USB Connector
BACK_LIGHT_SW
LED-
ABCD

DVH-860AV/XEUW5
16
1234
1234
C
D
F
A
B
E
5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
if Acc on
if Press power on key
Acc = 12 V
Starts
communication
with Grille
microcomputer.
Source keys
operative
Source ON
Completes power-on operation.
(After that, proceed to each source operation)
Power ON
Battery = 12 V
DVD Power = 5 V
Vcc = 5 V
TFT Power
On and TFT
Init
Entery select
mode
operative

DVH-860AV/XEUW5 17
5 678
5678
C
D
F
A
B
E
5.2 ERROR CODE LIST
Message Cause Action
Loading Disc is being read Please wait, it may take several minutes for
some disc or storage device.
No Disc
Disc is dirty Clean disc with soft cloth
Disc is upside down Insert disc with label side up
Disc not present in loading
compartment Insert disc
Bad Disc Disc is dirty Clean disc with soft cloth
Disc is upside down Insert disc with label side up
Unknown disc Disc format is not compatible with
this unit Change another disc.
Change to a supported file.
Change to a supported file.
content
Wrong file
Video resolution
not supported
The video resolutionexceeds
The file is not supported.
720X576.
Region Error DVD is not compatible with region
code of unit Use discs with corresponding regional code.
Error Illegal mechanism operation Press EJECT key for 5 seconds to reset
loading mechanism.
AMP ERROR
Unit fails to operate or speaker
connection is incorrect; protective
circuit is activated.
Check the speaker connection. If the message
fails to disappear even after the engine
is switched off/on, contact your dealer or
an authorized Pioneer Service Station for
assistance.

DVH-860AV/XEUW5
18
1234
1234
C
D
F
A
B
E
5.3 CONNECTOR FUNCTION DESCRIPTION
BT Antenna Do not connect
the wire to metal
body
1: FR-
2: FL+
3: FR+
4: FL-
5: RR+
6: ILLU_IN
7: RR-
8: ANT
9: T_MUTE
10: +B
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
17
18
19
20
11: RL+
12: GND
13: RL-
14: LO-FL
15: ACCIN
16: LO-FR
17: GND
18: GND
19: LO/SUB-RR
20: LO/SUB-RL
Fuse 10A
(Light Green/
White)
Radio Antenna
Parking SW
(Active low level input)
(Pink)
SWC (Steering Wheel Control)
Reverse
AUDIO IN (AV)
L(White)
R(Red)
VIDEO OUT
(Yellow)
To Monitor with
NTSC system
(Yellow)
CAMERA IN
(Yellow)
VIDEO IN (AV)
(Black)
MIC
Only RD, RI, BR

DVH-860AV/XEUW5 19
5 678
5678
C
D
F
A
B
E
6. SERVICE MODE
6.1 SOFTWARE VERSION INFORMATION DISPLAY
MODEL: DVH-850AVBT/XERD
MPEG CHIP: ZORAN36966H
MPEG VERSION: V0.24_20120922
PCB:V1.0
Disc Region: 4
MCU DATE: 09.20.12
MCU VERSION: 01.03
BT Firmware: V00.46R00.25
Example of a display
1) Enter into the setting menu by press and hold "SEL" key.
2) Press "5" "4" "3" "2" by numeric keys on the remote control.
Then, you will find the version information as shown below.
To exit the version display mode, press the "ESC" key.

DVH-860AV/XEUW5
20
1234
1234
C
D
F
A
B
E
6.2 SOFTWARE VERSION UP METHOD
Save six (6) sorts of file for Version Up (build.img, UPD_MPEG.VER, update.img, UPD_MCU.VER, UPD_BT.VER and
NFOREBT.dfu) on an USB.
Turn the product power to be ON and insert the above mentioned USB.
1. MPEG software update
2. MCU software update
3. BT software update (Only a model with BT functional)
4. Reset, "do default setting" in the setting menu.
5. Check Version
Insertion of USB will display the following Update screen.
UW5 model
Method of individual upgrading
Prepare files shown below according to the purpose for upgrading the software. (It is not necessary to prepare all files)
Item to upgrade Use software
MPEG build.img , UPD_MPEG.VER
MCU update.img , UPD_MCU.VER
BT NFOREBT.dfu , UPD_BT.VER
Upgrade the software in the order of MPEG, MCU, and BT.
Please be sure to perform Default Settings in the Setting after performing Version Up.
If you do not perform the Version Up, the initialization of MPEG software will not be executed.
In addition, the Main Body Reset SW located at the rear surface of Detach Panel is only for the Restart RESET
of MCU and it does not mean to perform all of the initializations.
(Language Setting: Russian for UW5 model)
BR model
(Language Setting: Portuguese(B) for BR model)