Pit Boss Ultimate Griddle PB2BGD2 User manual

MODEL / MODÈLE / MODELO / MODELL / MODELLO : PB2BGD2
PART / PIÈCE / PARTE / TEIL / PARTE : 10807, 10808, 10809
WARNING:          
          
 ,         
       
  
AVERTISSEMENT:   '     
           
   ,     
        
    '     
ADVERTENCIA:           
       ,   
,         
           
           
ACHTUNG:        , 
        
   ,     
        
          
AVVERTENZA:  '   '  '
         
    ,     
     '      
         
  
  |  '
   |  |   
2 
  
IMPORTANT, READ CAREFULLY, RETAIN
FOR FUTURE REFERENCE. MANUAL MUST
BE READ BEFORE OPERATING!
  
2   

IMPORTANT, PRENEZ CONNAISSANCE DE
CE DOCUMENT ET CONSERVEZ-LE POUR
RÉFÉRENCE ULTÉRIEURE. VOUS DEVEZ LIRE
CE GUIDE AVANT D’UTILISER LE BARBECUE!
 2 
  
IMPORTANTE, LEER DETENIDAMENTE,
CONSERVAR PARA REFERENCIA FUTURA.
LEA EL MANUAL ANTES DEL USO!
2 
  
WICHTIG: AUFMERKSAM LESEN UND GUT
AUFBEWAHREN BITTE UNBEDINGT VOR
GEBRAUCH DIE BEDIENUNGSANLEITUNG
SORGFÄLTIG DURCHLESEN!
 2 
  
IMPORTANTE: LEGGERE ATTENTAMENTE E
CONSERVARE PER RIFERIMENTO FUTURO.
LEGGERE IL MANUALE PRIMA DELL'USO.
For outdoor nd household use onl Not for commercl use
Réservé  l'use extéreur et résdentel unquement Non destné  un use commercl
Solo pr uso doméstco  en el exteror No pto pr uso comercl
Nur zur Verwendun m Außenberech und fr den prvten Gebruch Ncht zur ewerblchen Nutzun eenet
Solo per uso domestco ed esterno Non per uso commercle

3
EN
ENGLISH
  
MODEL ASSEMBLED (WxDxH) WEIGHT COOKING AREA HEAT INPUT
 22 1,273  728  940  /
50.1  28.6  37.0  46.4  / 102.3  2,720  / 421.6  7.63 
Part# Description
1 Firebox (x1)
2 Hot Plate (x1)
3 Hot Plate Leg Screws (x4)
4 Grease Cup (x1)
5 Lid Support (x1)
6 Lid Handle Bezel (x2)
7 Lid Handle (x1)
8 Cart Front Panel (x1)
9 Cart Back Panel (x1)
10 Cart Side Panel - Left (x1)
11 Cart Side Panel - Right (x1)
12 Side Shelf - Left (x1)
13 Side Shelf - Right (x1)
14 Paper Towel Hook (x1)
15 Side Shelf Bracket - Left (x2)
16 Side Shelf Bracket - Right (x2)
17 Support Leg for Caster - Front (x1)
18 Support Leg for Caster - Back (x1)
19 Support Leg for Wheel - Front (x1)
20 Support Leg for Wheel - Back (x1)
21 Bottle Opener (x1)
22 Locking Caster (x2)
23 Wheel (x2)
24 Bottom Shelf (x1)
A Screw (x37)
B Washer (x16)
C Locking Washer (x16)
D Screw (x4)
E Wheel Cotter Pin (x2)
F Wheel Washer (x2)
G Wheel Axle Pin (x2)
H Battery (x1)
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Care if parts are missing when assembling the unit.
1
2
5
4
  
  
 
6
7
9
8
10
3
11
21
14 12
13
17
18
19
20
15
23
24
16
22

4
EN ENGLISH
 
IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws
completely until all screws for that step have been installed. Hardware combination involving a locking washer and
washer should be installed with the locking washer closest to the head of the screw.
1.      
Parts Required:
1 x Support Leg for Caster / Front (#17)
1 x Support Leg for Caster / Back (#18)
1 x Support Leg for Wheel / Front (#19)
1 x Support Leg for Wheel / Back (#20)
2 x Locking Caster (#22)
2 x Wheel (#23)
2 x Wheel Cotter Pin (#E)
2 x Wheel Washer (#F)
2 x Wheel Axle Pin (#G)
Installation:
• Attach the Wheel to the Support Leg for Wheel by inserting the Wheel
Axle Pin through the Wheel, Support Leg hole, Wheel Washer, then
secure using the Wheel Cotter Pin. Repeat installation for the other
Support Leg with Wheel. Note illustration 1A.
• Install a Locking Caster Wheel to the bottom of a Support Leg by
hand-tightening into the hole. The Locking Caster Wheel is inserted
completely when it cannot rotate any further into the Support Leg.
Repeat installation for second Support Leg. Note illustration 1B.
 
Parts are located throughout the shipping carton, including underneath the griddle. Inspect the unit, parts, and hardware blister
pack after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the griddle
before assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt
to assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss® Grills Customer Care.
www.pitboss-grills.com
IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.
Tools required for assembly: screwdriver and wrench. Tools not included.
1
1

19
20
17
18


23
22

5
EN
ENGLISH
2.    
Parts Required:
1 x Bottom Shelf (#24)
4 x Screw (#A)
4 x Washer (#B)
4 x Locking Washer (#C)
Installation:
• Place a piece of cardboard on the floor to prevent scratching the unit
and parts during assembly.
NOTE: Ensure the flat surface of the Bottom Shelf is facing up.
• Attach the Bottom Shelf to one Support Leg with Wheel by carefully
aligning it into the corner, then secure using one washer, locking washer,
and screw. Repeat installation for the other three Support Legs to the
remaining three corners of the Bottom Shelf. See illustration for proper
arrangement of the Support Legs.
3.    
Parts Required:
1 x Cart Front Panel (#8)
1 x Cart Back Panel (#9)
1 x Cart Side Panel - Left (#10)
1 x Cart Side Panel - Right (#11)
16 x Screw (#A)
Installation:
• Install the Cart Front Panel between the front Support Legs of the Cart
Base. Secure using two screws into each Support Leg. Repeat same
installation for the Cart Back Panel. Note illustration 3A.
NOTE: Ensure the "PIT BOSS" of the Cart Front Panel is facing the
front of the unit. The flat surface of the Cart Back Panel should face
towards the back.
• Install the Cart Side Panel Left between the left Support Legs of the
Cart Base. Secure using two screws into each Support Leg. Repeat same
installation for the Cart Side Panel Right to the right Support Legs of the
Cart Base. Note illustration 3B.
IMPORTANT: The latches on the Cart Side Panels should face forward.
2
3
3
17 18
24
20



19


9
8
10
11


6
EN ENGLISH
4.     
Parts Required:
2 x Side Shelf Bracket - Left (#15)
2 x Side Shelf Bracket - Right (#16)
12 x Screw (#A)
12 x Washer (#B)
12 x Locking Washer (#C)
Installation:
• Mount one Side Shelf Bracket to a Support Leg using three washers,
locking washers and screws. Install each screw halfway first, then
tighten completely when all three screws are mounted and aligned
properly. Repeat installation for the other three Side Shelf Brackets to
the remaining three Support Legs.
5.    
Parts Required:
1 x Side Shelf - Left (#12)
1 x Side Shelf - Right (#13)
4 x Screw (#D)
Installation:
• Align and position one Side Shelf on the Side Shelf Brackets on one side
of the unit. From underneath, secure a screw into each corner, as shown
in illustration. Repeat same installation for the Side Shelf on the other
side of the unit.
NOTE: Once installed, both Side Shelves can be raised (for use) or
lowered (for storage) with ease.
IMPORTANT: Avoid using the Side Shelves to move or lift the unit.
The weight of the unit will cause the shelves to break, which is not
covered by warranty.
6.    
Parts Required:
1 x Paper Towel Hook (#14)
1 x Bottle Opener (#21)
2 x Screw (#A)
Installation:
• Mount the Bottom Opener to the Front-Left Support Leg using two
screws. Note illustration for correct orientation, with opening angled
downwards.
• Install the Paper Towel Hook on the two pre-mounted screws of the
same Support Leg. Press down to ensure the Paper Towel Hook stays
secure in place.
4
6
5
15
16
15
16



12
14
21


13


7
EN
ENGLISH
7.    
Parts Required:
1 x Firebox (#1)
2 x Lid Handle Bezel (#6)
1 x Lid Handle (#7)
Installation:
• Remove the pre-installed screws from the Lid Handle. From inside the
lid of the Firebox, insert one screw to protrude to the outside. Add a
Lid Handle Bezel on the screw, then hand-tighten the screw (from the
inside) into the Lid Handle. Repeat same installation for other end of Lid
Handle.
8.    
Parts Required:
1 x Lid Support (#5)
3 x Screw (#A)
Installation:
• On the backside of the Firebox, fasten the Lid Support to the center of
the panel using three screws.
9.      
NOTE: A regulator is shown; however, not all distributors sell the units with
a regulator included. A Manifold Transition Kit is provided should a gas
regulator not come pre-assembled on the griddle. Select the connector
from the Manifold Transition Kit that is required for your gas manifold and
regulator tubing.
Installation:
• Place the Firebox next to the Cart, both facing the same direction. Using
two people, lift the Firebox using the inset grooves on each side. Slowly,
place the Firebox onto the cart frame, passing the regulator and hosing
through the Cart side Panel on the right of the unit. Note illustration 9A.
IMPORTANT: Take care to avoid pinching or damaging the regulator
or hosing during installation of the Firebox to the Cart. Poor
installation may cause the parts to not function properly.
• Once in position, turn the latches (one on each side) to lock the Firebox
into the Cart. Note illustration 9B.
77
6
6
1
9
9
8
5


8
EN ENGLISH
10.     
Parts Required:
1 x Hot Plate (#2)
4 x Hot Plate Screws (#3)
Installation:
• Turn the Hot Plate upside-down. Insert a Hot Plate Screw into a corner
hole of the Hot Plate, turning by hand, until it cannot rotate any further
into the nut. Repeat same installation on the other three corner holes.
11.    
Parts Required:
1 x Grease Cup (#4)
Installation:
• Open the Firebox lid. Carefully, place the Hot Plate into the Firebox. Once
the Hot Plate is installed, ensure it sits level in the Firebox. Adjust the
height of the Hot Plate Screws, if needed, so the Hot Plate is level.
NOTE: To maintain the searing and grilling performance of your Hot
Plate, regular care and maintenance is required.
• Place the Grease Cup into the Grease Cup housing on the front of the
Firebox, as shown in the illustration.
12.    
Parts Required:
1 x Battery (#H)
Installation:
• Turn the ignition button cap counter-clockwise to remove it. Insert the
Battery into the housing with the positive (+) terminal facing outward.
Screw the ignition button cap back into place to cover.
• The unit is now completely assembled.
Refer to Owner's Manual for Operating Instructions.
11
4
12

10 3
3
3
3
2