Pitney Bowes Integra N300 User manual

1
SV60424 Rev. E 2/00 ©2000 Pitney Bowes Inc. Fifth Edition, February 2000. All Rights Reserved. Printed in USA.
Installation Instructions
for the Integra™ N300 2-lb. Scale
User Guide
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Do not connect power until Step 10.
3
Place the scale near a wall outlet and within
cable reach of your postage meter (if you
have one). IMPORTANT: Ensure the scale
location is free of drafts and the scale is not
touching objects that may affect the weight
reading.
Place your scale on a level
surface.
Your Pitney Bowes
postage meter
1
Power Cord Scale-Meter Interface Cable
(if ordered, packed separately)
Make sure you have:
✓Scale
✓User Guide
✓Power Cord (in its own box)
✓Scale-Meter Interface Cable
2
Scale
(if ordered, packed separately)

2
Locate
the plug
ports
under the
front of the scale
and plug in the small end
of the power cord.
4
If you're
using a
Pitney Bowes
meter, plug the small end of the scale-meter
interface cable into the scale port.
6
Level the scale by turning the scale feet until
the leveling bubble is centered and the scale
does not wobble.
7
8
Lift the
platter,
remove the
packing
material,
and replace
the platter on the scale.
Tuck the
cord(s)
under the
guides on the
bottom of the
scale.
9
If you're using a Pitney Bowes meter, connect
the large end of the scale-meter interface
cable to your meter's communications port.
Tighten the thumbscrews securely. See the
meter's operating guide for the location of
the port.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
;;
;;
Remove packing. Level the scale.
Bubble must
be in center.
Adjustable
Feet (4)
Locate the plug ports. Connect scale-meter interface
cable to scale.
Tuck the cords under the
guides. Connect scale-meter interface
cable to meter.
5
or

3
a. Find the number corresponding
to your state in the chart at
right.
b. At the LC prompt, press the
Zero key to display the first
code. Continue pressing Zero to
advance to your state's code.
c. Ensure that the code on the
display matches your state's
code.
d. Press the Certified key.
Note: Your scale will not work unless you perform this step.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Enter your location code.
Location Codes
State Code
Ohio 72
Oklahoma 61
Oregon 72
Pennsylvania 72
Rhode Island 72
South Carolina 50
South Dakota 72
Tennessee 61
Texas 50
Utah 61
Vermont 72
Virginia 61
Washington, DC 72
Washington 84
West Virginia 61
Wisconsin 72
Wyoming 72
State Code
Louisiana 50
Maine 72
Maryland 72
Massachusetts 72
Michigan 72
Minnesota 84
Mississippi 50
Missouri 61
Montana 84
Nebraska 72
Nevada 61
New Hampshire 72
New Jersey 72
New Mexico 50
New York 72
North Carolina 61
North Dakota 84
State Code
Alabama 50
Alaska 06
Arizona 50
Arkansas 61
California 61
Colorado 61
Connecticut 72
Delaware 72
Florida 50
Georgia 50
Hawaii 43
Idaho 72
Illinois 72
Indiana 72
Iowa 72
Kansas 61
Kentucky 61
The scale displays 0 lb 0.0 oz and the
Select Class arrow flashes. This is the
ready mode.
Result: The scale powers up and displays
the LC (location code) prompt below.
Go to Step 11 to continue.
Plug power cord into outlet.
Note: If the scale does not power-up, check
that the power cord is firmly attached. Also
check that the wall outlet you are using has
power by plugging in another device.
10
11

4
For information on using the scale, refer to the User Guide.
*SV60424Rev.E*
Congratulations!
You have successfully installed your Pitney Bowes electronic scale.
If you have any questions about the initial setup,
BE NEAR YOUR SCALE
and call 1-800-537-2488 (menu option 1).
Or visit our website at www.pitneybowes.com/ms_service/support/integra