Pittsburgh PRO 00239 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2009 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 15k

Page 2 For technical questions, please call 1-888-866-5797. Item 00239
Specifications
Torque Range 10 - 150 ft-lb
Drive 1/2"
Accuracy ± 4%
Important Safety Information
WARNING Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in injury.
Save all warnings and instructions for future reference.
1. The warnings, cautions, and instructions
in this instruction manual cannot cover all
possible conditions and situations that may
occur. It must be understood by the operator
that common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
2. Wear ANSI-approved safety
goggles during use.
3. Do not use for loosening fasteners.
4. Use only within rated torque range.
5. Use as intended only. Do not
use as hammer or pry bar.
6. Do not use handle extension to increase
force. Do not use as a breaker bar.
7. Do not use a Torque Wrench that
has been dropped. Have it tested
before putting back into use.
8. Have the Torque Wrench calibrated and
serviced only by a qualified technician.
9. Inspect before every use; do not use
if damaged or if parts are loose.
10. Keep away from children.
11. Use only sockets with the correct
drive and rated to at least the
torque that will be applied to it.
Operating Instructions
Square
Drive
Torque
Scale
Knurled
Handle
Lock
Knob
CAUTION! Wear ANSI-approved
safety goggles during use.
Note: The Torque Wrench is marked with
Foot Pounds and Newton Meters
(on opposite sides of Upper Handle). The
following instructions illustrate use in Foot Pounds.
1. BEFORE EVERY USE, exercise Torque
Wrench. Loosen Lock Knob
(see step 5 on page 3), then perform
the following exercise three times:
a. Turn Knurled Handle to the right until
maximum torque setting is reached.
b. Turn handle to the left until minimum
torque setting is reached.

Page 3For technical questions, please call 1-888-866-5797.Item 00239
2. Refer to equipment manufacturer’s
instructions for torque value.
3. Clean the fastener’s threads. Dirty threads
may result in a misleading torque reading.
4. Select socket that properly fits the fastener.
Press socket firmly onto Square Drive.
5. Loosen the Lock Knob by turning it
counterclockwise until it stops.
6. To set torque value to 76:
a. Turn the Knurled Handle until top of handle
lines up with bottom horizontal mark
for 70 and 0 lines up with center line.
08
2
90
110
130
FOOT POUNDS
6
4
80
100
120
140
70
150
b. Turn Knurled Handle until the 6 lines
up with the center line. The torque
value is set to 76 in.-lb. (70 + 6 = 76)
64
8
90
110
130
FOOT POUNDS
2
0
80
100
120
140
70
150
7. Tighten the Lock Knob by turning
it clockwise until it stops.
CAUTION: To prevent damage to the Torque
Wrench, do not use for loosening fasteners.
8. Set Switch to ON position. The
Torque Wrench can only measure
torque during clockwise operation.
On
Position
Note: Thread fastener with another
tool until it is snug, then finish the
operation with the Torque Wrench.
9. Place socket on fastener, then grasp the
Knurled Handle and pull smoothly and
slowly until the handle breaks away and
a click is heard or felt. STOP PULLING!
The proper torque has been achieved.
Further pulling may damage fastener.
10. Release pressure to allow the handle
to reset for the next operation.
11. AFTER EVERY USE, loosen the Lock
Knob, set to the lowest torque setting,
then tighten the Lock Knob.
12. Store Wrench inside its case,
indoors, in a clean, dry location
that is out of reach of children.

Maintenance and Servicing
Procedures not specifically explained in this manual
must be performed only by a qualified technician.
TO PREVENT INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs,
have the problem corrected before further use.
1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts, and
• any other condition that may
affect its safe operation.
2. AFTER EVERY USE:
• loosen the Lock Knob, set to the lowest
torque setting, then tighten the Lock Knob.
• wipe wrench with a clean cloth.
Do not use liquid on the cloth or
immerse wrench in liquid.
3. EVERY 6 MONTHS, have the
Torque Wrench calibrated and
serviced by a qualified technician.
Note: Replacement parts are not available.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797