Planar Dome E4c User manual

Dome E4c Display
MX4 Display Controller
Quick Reference
Windows XP
Windows 2000
020-0496-00A_1.indd 1020-0496-00A_1.indd 1 8/22/06 4:44:59 PM8/22/06 4:44:59 PM

2
Display Features
•AMLCD color panel designed for
widescreen diagnostic imaging.
•High resolution and high contrast
ratio combined for viewing color
and grayscale images simultane-
ously.
•Bezel-free framing of 4 megapixels
of data presented in a landscape
resolution of 2560 x 1600 pixels.
•Gamma correction achieved on
true color display from a palette of
1786 near-gray values.
•Integrated RightLight technology
applied to monitor and stabilize
backlight luminance.
System Requirements
•PCI slot (64-bit recommended)
•50 MB hard disk space
•256 MB RAM
•CD-ROM drive
•Power supply, 350 watts or greater
•Windows XP Service Pack 1 or
Windows 2000 Service Pack 4
•.NET Framework 1.1
Read all instructions before setting up the Dome E4c display. Improper use of
the display can result in electric shock, re, or damage to display components.
Go to www.planar.com/support for more product documentation.
Warning
Avertissement
Avvertenza
Advertencia
Warnung
Wear an antistatic heel or wrist strap
when installing the video card to avoid
damage to computer components.
020-0496-00A_1.indd 2020-0496-00A_1.indd 2 8/22/06 4:45:03 PM8/22/06 4:45:03 PM

3
Check the contents of your Dome E4c display package for all the items shown
here. Save the original packaging materials for storage and shipping.
IMPORTANT: Read “Handling the Display” on page 10 before you set up
the display.
Unpacking the Display
Software CDsPower cord
Graphics card Power adapter
Option available: VESA wall mounting kit.
Quick reference
020-0496-00A_1.indd 3020-0496-00A_1.indd 3 8/22/06 4:45:04 PM8/22/06 4:45:04 PM

4
Display Components
The LED on the display front
indicates display status. Green, the
display is connected and running
properly. Amber, the video signal is
not being received.
The integrated video cable and
input power port are located on
the back. NOTE: When you con-
nect the dual-link DVI cable to the
graphics card, you must attach the
cable connector to the bottom port
of the card. In operation, when the
cable is disconnected, the display
backlight turns o and the unit
enters power-saving mode.
No other user-accessible controls
are available. You must use the
Dome CXtra software to control
display brightness and power-
saving functions.
After installation, the display turns
on automatically when you turn
on your computer system.
LED
020-0496-00A_1.indd 4020-0496-00A_1.indd 4 8/22/06 4:45:05 PM8/22/06 4:45:05 PM

5
(bottom view without stand)
Integrated
DVI cable
Power
port
020-0496-00A_1.indd 5020-0496-00A_1.indd 5 8/22/06 4:45:05 PM8/22/06 4:45:05 PM

6
Installing the Display Controller
To install the controller
1 Turn o your computer and all peripherals.
Disconnect all cables from your computer.
Leave the power cord plugged into the
grounded outlet.
2 Remove the computer cover.
3 Remove any existing graphics card and video
signal cable, if necessary.
4 Remove the blank bracket from the available
PCI slot.
5 Insert the controller into the slot, align the
connector pins, and press the board down
until it is rmly seated.
6 Secure the mounting bracket.
7 Reattach the computer cover and the
peripherals.
Remove any existing graphics card and its driver from your computer system
before you install the MX4 board and driver. Also disable any onboard graphics
capability on the motherboard. See safety precautions on page 2.
Open PCI slot
Blank bracket
MX4 board installed
020-0496-00A_1.indd 6020-0496-00A_1.indd 6 8/22/06 4:45:05 PM8/22/06 4:45:05 PM

7
Connecting the Display
To connect the display
1 Plug the DVI cable into the bottom
video port of the installed controller.
(Only the bottom port allows you to
enable dual-link functionality.
Use the bottom port to support the
display with the full, non-scaled
2560 x 1600 resolution.)
2 Plug the power cord into the input
power port on the connector plate.
3 Plug the power cord from the power
adapter into a grounded outlet.
NOTE: The display turns on automatically
when you turn on your computer system.
Use only the power cord supplied with your display.
Connect the
DVI cable to the
bottom port for
dual-link functionality.
DVI
port 1
MX4 board
installed
DVI cable
Connection for
a single display
020-0496-00A_1.indd 7020-0496-00A_1.indd 7 8/22/06 4:45:06 PM8/22/06 4:45:06 PM

8
Before you install the driver, remove any previously installed display driver
for the display controller from your system.
To install the display driver
1 Start your computer system. Click Cancel on the Found New Hardware Wizard.
Click No at the restart prompt.
2 Insert the driver installation CD and click Next.
3 Auto-detection reports the driver version and graphics board(s). Click Next.
4 Click the check box to enable independent mode for each graphics card.
Click Next.
5 Click Next to continue. File copy begins.
6 Click Continue Anyway on the dialog reporting no digital signature.
Repeat for a second graphics card.
7 Click Next upon completion of the driver installation.
8 Select the Restart computer option and click Finish.
To congure the display
1 Right-click the desktop and select Properties > Settings.
2 Use the native resolution of the display, 2560x1600.
3 For use of the second display, select Extend my Windows desktop onto
this monitor.
4 Click OK until you return to the desktop.
Installing the Display Driver
020-0496-00A_1.indd 8020-0496-00A_1.indd 8 8/22/06 4:45:06 PM8/22/06 4:45:06 PM

9
Use the PowerDesk dialog to make changes to the video settings.
To rotate the display
1 Click the PowerDesk icon (on taskbar), and select Monitor Adjustments on the
PowerDesk menu.
2 Select Adjust Orientation, then the degree of rotation. Click OK.
To set up multi-display mode
1 Click the PowerDesk icon, and select Multi-Display Setup.
2 Select the device and multi-display setup you want to use. Click OK.
To change video setting per display
1 Click the PowerDesk icon.
2 On the PowerDesk menu, select the graphics card representing the display you
want to change video settings on, then select Grayscale Setup category.
NOTE: Grayscale mode is the installation default.
3 Select one of the options: Use Color (RGB mode) or 256 (Grayscale mode).
When using the grayscale mode, be sure to select the xed linear gray palette.
4 Click OK, then restart the system.
NOTE: You must restart the system each time you change the video settings of a
display. For dual congurations, change the settings of the rst display and restart
the system, then change the settings of the second display and restart.
To set the brightness
You must have the Dome CXtra software installed to change the display
brightness. Adjust the value of the white level on the Backlight tab of the
RightLight Panel Conguration.
Adjusting the Display Properties
020-0496-00A_1.indd 9020-0496-00A_1.indd 9 8/22/06 4:45:06 PM8/22/06 4:45:06 PM

10
Handling the Display
•Set up your display on a stable,
level surface away from any direct
light or heat source, but near a
grounded AC outlet.
•Choose a well-ventilated location
with an adequate amount of space.
Do not block the vents on the back
of the display.
•Never lift the display by the desk
stand. Use both hands to lift or
move the display. Avoid touching
the screen.
•Never apply pressure to the screen
or touch the screen with bare ngers
or with any objects.
•Allow the display unit to reach room
temperature before you power it on.
Ambient room temperature ranges
from 20°C to 25°C (68°F to 77°F).
•Avoid sudden temperature changes
in the environment, as this may
cause condensation in the display.
•Never remove the back cover or
disassemble the display. There are
no user-serviceable parts inside.
•When troubleshooting, check that
all cables are properly connected
and that your computer is turned on
or not in power-saving mode.
•Follow your local governing
ordinance for proper disposal or
recycling of electronic components.
Hand injury may result from misuse of the desk stand when
lowering the display height. Avoid holding the bottom area
of the display. Never place your hands between the display
and the desk stand.
To lower the display height, grasp both sides of the display
and push down.
020-0496-00A_1.indd 10020-0496-00A_1.indd 10 8/22/06 4:45:07 PM8/22/06 4:45:07 PM