Planet Networking & Communication IPM-4220 User manual

– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
Thank you for choosing PLANET IP-based Switched Power Manager. The
Switched IPM provides the useful function of managing power for any
combination to connect with itself.
Open the box of the Switched IPM and carefully unpack it. The box
should contain the following items:
Switched IP Power Manager x 1 Quick Guide x 1
Power Cord x 1 Rack-mounting Kit (Only for IPM-8220) x 1
Note
If there is any item missing or damaged, please contact
the seller immediately.
2. Installation Precautions
Please set the maximum power-off protection allowed by power circuit
as per the rated current information indicated on the device with
reference to the local state rules, safety procedures and disconnector
deviation.
The unit can only be connected to a grounded power outlet or system.
Make sure the total current output of all the connected systems within
the rated current indicated on the device.
The test results of this device may be inaccurate giving unstable
power supply.
Avoid using this device in places near water or moisture environments.
Use the attachments/accessories specied by the manufacturer only.
Please avoid any items or liquids entering the device because their
contact with dangerous voltage points or short-circuit parts may cause
a re or electric shock.
3 Physical Introduction
IPM-4220
Rear Panel :
1
3
45 6 7 8 9
2
Front Panel :
15
10 11 12 13 14
16
17
1
System Indicating Light
Slow ashing: Normal operating
Rapid ashing: Normal updating
2Reset and Warning Indicating Light
3Temperature/Humidity Port for IPM-ESB Connection
4Reset Button
5RJ45 Ethernet Port
6USB Connected Port (Future Feature)
7
COM2/1
2 Com Ports provided to enable terminal control, API control and
2 mutual cascading
8Circuit Breaker Protection
9Power Inlet
10 Power On/Off Switch
11 Power Outlet
Note: The maximum output current is 16 amps.
12 LCD Panel
To display total current, voltage and IP
13
Switch/Set button
Provide LCD panel in order to switch the total current and IP; set
alarm current
14
IP Indicating Light
Lights remaining lit: IP displaying
Slow ashing: Max. current of alarm occurrence
15
Alarm Indicating Light
Lights remaining lit: Alarm has occurred
Slow ashing: There was current overloading
16 Buzzering
17 Power Outlet Indicating Light
Panel Operation
The rst mode of LCD is total current, switching with the Switch/Set
button to show the regular sequence of total current, max. current and
IP shown below:
0.0
0.0
192
168
010
001
Total Current
IP Display
IP Display Max. Current
IP Display IP Display
■ Alarm and IP indicating light
will not flash.
■ IP indicating light is flashing
because of overload.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light is flashing.
1
33
33
2
 1LCD menu shows the total current. èHold the Switch/Set button
for 3 seconds with a long beep to enter alarm current setting. è
Press the Switch/Set button to increase the alarm current by 0.5A
in each press. èHold the Switch/Set button for 3seconds with a
“beep” to save the setting.
 2Press the Switch/Set button and shows the maximum current.
èHold the Switch/Set button for 3seconds with a long beep to
adjust to a zero point.
 3Press the Switch/Set button to switch the display of each IP
address.
IPM-8220
Rear Panel :
1
3
45 6 7 8 9
2
Front Panel :
14
10 11 12 13
1516
1
System Indicating Light
Slow ashing: Normal operating
Rapid ashing: Normal updating
2Reset and Warning Indicating Light
3Temperature/Humidity Port for IPM-ESB Connection
IPM-4220/IPM-8220
Quick Installation Guide
IP-based 4-/8-port Switched
Power Manager

– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
Thank you for choosing PLANET IP-based Switched Power Manager. The
Switched IPM provides the useful function of managing power for any
combination to connect with itself.
Open the box of the Switched IPM and carefully unpack it. The box
should contain the following items:
Switched IP Power Manager x 1 Quick Guide x 1
Power Cord x 1 Rack-mounting Kit (Only for IPM-8220) x 1
Note
If there is any item missing or damaged, please contact
the seller immediately.
2. Installation Precautions
Please set the maximum power-off protection allowed by power circuit
as per the rated current information indicated on the device with
reference to the local state rules, safety procedures and disconnector
deviation.
The unit can only be connected to a grounded power outlet or system.
Make sure the total current output of all the connected systems within
the rated current indicated on the device.
The test results of this device may be inaccurate giving unstable
power supply.
Avoid using this device in places near water or moisture environments.
Use the attachments/accessories specied by the manufacturer only.
Please avoid any items or liquids entering the device because their
contact with dangerous voltage points or short-circuit parts may cause
a re or electric shock.
3 Physical Introduction
IPM-4220
Rear Panel :
1
3
45 6 7 8 9
2
Front Panel :
15
10 11 12 13 14
16
17
1
System Indicating Light
Slow ashing: Normal operating
Rapid ashing: Normal updating
2Reset and Warning Indicating Light
3Temperature/Humidity Port for IPM-ESB Connection
4Reset Button
5RJ45 Ethernet Port
6USB Connected Port (Future Feature)
7
COM2/1
2 Com Ports provided to enable terminal control, API control and
2 mutual cascading
8Circuit Breaker Protection
9Power Inlet
10 Power On/Off Switch
11 Power Outlet
Note: The maximum output current is 16 amps.
12 LCD Panel
To display total current, voltage and IP
13
Switch/Set button
Provide LCD panel in order to switch the total current and IP; set
alarm current
14
IP Indicating Light
Lights remaining lit: IP displaying
Slow ashing: Max. current of alarm occurrence
15
Alarm Indicating Light
Lights remaining lit: Alarm has occurred
Slow ashing: There was current overloading
16 Buzzering
17 Power Outlet Indicating Light
Panel Operation
The rst mode of LCD is total current, switching with the Switch/Set
button to show the regular sequence of total current, max. current and
IP shown below:
0.0
0.0
192
168
010
001
Total Current
IP Display
IP Display Max. Current
IP Display IP Display
■ Alarm and IP indicating light
will not flash.
■ IP indicating light is flashing
because of overload.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light is flashing.
1
33
33
2
 1LCD menu shows the total current. èHold the Switch/Set button
for 3 seconds with a long beep to enter alarm current setting. è
Press the Switch/Set button to increase the alarm current by 0.5A
in each press. èHold the Switch/Set button for 3seconds with a
“beep” to save the setting.
 2Press the Switch/Set button and shows the maximum current.
èHold the Switch/Set button for 3seconds with a long beep to
adjust to a zero point.
 3Press the Switch/Set button to switch the display of each IP
address.
IPM-8220
Rear Panel :
1
3
45 6 7 8 9
2
Front Panel :
14
10 11 12 13
1516
1
System Indicating Light
Slow ashing: Normal operating
Rapid ashing: Normal updating
2Reset and Warning Indicating Light
3Temperature/Humidity Port for IPM-ESB Connection
IPM-4220/IPM-8220
Quick Installation Guide
IP-based 4-/8-port Switched
Power Manager

– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
Thank you for choosing PLANET IP-based Switched Power Manager. The
Switched IPM provides the useful function of managing power for any
combination to connect with itself.
Open the box of the Switched IPM and carefully unpack it. The box
should contain the following items:
Switched IP Power Manager x 1 Quick Guide x 1
Power Cord x 1 Rack-mounting Kit (Only for IPM-8220) x 1
Note
If there is any item missing or damaged, please contact
the seller immediately.
2. Installation Precautions
Please set the maximum power-off protection allowed by power circuit
as per the rated current information indicated on the device with
reference to the local state rules, safety procedures and disconnector
deviation.
The unit can only be connected to a grounded power outlet or system.
Make sure the total current output of all the connected systems within
the rated current indicated on the device.
The test results of this device may be inaccurate giving unstable
power supply.
Avoid using this device in places near water or moisture environments.
Use the attachments/accessories specied by the manufacturer only.
Please avoid any items or liquids entering the device because their
contact with dangerous voltage points or short-circuit parts may cause
a re or electric shock.
3 Physical Introduction
IPM-4220
Rear Panel :
1
3
45 6 7 8 9
2
Front Panel :
15
10 11 12 13 14
16
17
1
System Indicating Light
Slow ashing: Normal operating
Rapid ashing: Normal updating
2Reset and Warning Indicating Light
3Temperature/Humidity Port for IPM-ESB Connection
4Reset Button
5RJ45 Ethernet Port
6USB Connected Port (Future Feature)
7
COM2/1
2 Com Ports provided to enable terminal control, API control and
2 mutual cascading
8Circuit Breaker Protection
9Power Inlet
10 Power On/Off Switch
11 Power Outlet
Note: The maximum output current is 16 amps.
12 LCD Panel
To display total current, voltage and IP
13
Switch/Set button
Provide LCD panel in order to switch the total current and IP; set
alarm current
14
IP Indicating Light
Lights remaining lit: IP displaying
Slow ashing: Max. current of alarm occurrence
15
Alarm Indicating Light
Lights remaining lit: Alarm has occurred
Slow ashing: There was current overloading
16 Buzzering
17 Power Outlet Indicating Light
Panel Operation
The rst mode of LCD is total current, switching with the Switch/Set
button to show the regular sequence of total current, max. current and
IP shown below:
0.0
0.0
192
168
010
001
Total Current
IP Display
IP Display Max. Current
IP Display IP Display
■ Alarm and IP indicating light
will not flash.
■ IP indicating light is flashing
because of overload.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light is flashing.
1
33
33
2
 1LCD menu shows the total current. èHold the Switch/Set button
for 3 seconds with a long beep to enter alarm current setting. è
Press the Switch/Set button to increase the alarm current by 0.5A
in each press. èHold the Switch/Set button for 3seconds with a
“beep” to save the setting.
 2Press the Switch/Set button and shows the maximum current.
èHold the Switch/Set button for 3seconds with a long beep to
adjust to a zero point.
 3Press the Switch/Set button to switch the display of each IP
address.
IPM-8220
Rear Panel :
1
3
45 6 7 8 9
2
Front Panel :
14
10 11 12 13
1516
1
System Indicating Light
Slow ashing: Normal operating
Rapid ashing: Normal updating
2Reset and Warning Indicating Light
3Temperature/Humidity Port for IPM-ESB Connection
IPM-4220/IPM-8220
Quick Installation Guide
IP-based 4-/8-port Switched
Power Manager

– 1 – – 2 –
– 3 – – 4 –
1. Package Contents
Thank you for choosing PLANET IP-based Switched Power Manager. The
Switched IPM provides the useful function of managing power for any
combination to connect with itself.
Open the box of the Switched IPM and carefully unpack it. The box
should contain the following items:
Switched IP Power Manager x 1 Quick Guide x 1
Power Cord x 1 Rack-mounting Kit (Only for IPM-8220) x 1
Note
If there is any item missing or damaged, please contact
the seller immediately.
2. Installation Precautions
Please set the maximum power-off protection allowed by power circuit
as per the rated current information indicated on the device with
reference to the local state rules, safety procedures and disconnector
deviation.
The unit can only be connected to a grounded power outlet or system.
Make sure the total current output of all the connected systems within
the rated current indicated on the device.
The test results of this device may be inaccurate giving unstable
power supply.
Avoid using this device in places near water or moisture environments.
Use the attachments/accessories specied by the manufacturer only.
Please avoid any items or liquids entering the device because their
contact with dangerous voltage points or short-circuit parts may cause
a re or electric shock.
3 Physical Introduction
IPM-4220
Rear Panel :
1
3
45 6 7 8 9
2
Front Panel :
15
10 11 12 13 14
16
17
1
System Indicating Light
Slow ashing: Normal operating
Rapid ashing: Normal updating
2Reset and Warning Indicating Light
3Temperature/Humidity Port for IPM-ESB Connection
4Reset Button
5RJ45 Ethernet Port
6USB Connected Port (Future Feature)
7
COM2/1
2 Com Ports provided to enable terminal control, API control and
2 mutual cascading
8Circuit Breaker Protection
9Power Inlet
10 Power On/Off Switch
11 Power Outlet
Note: The maximum output current is 16 amps.
12 LCD Panel
To display total current, voltage and IP
13
Switch/Set button
Provide LCD panel in order to switch the total current and IP; set
alarm current
14
IP Indicating Light
Lights remaining lit: IP displaying
Slow ashing: Max. current of alarm occurrence
15
Alarm Indicating Light
Lights remaining lit: Alarm has occurred
Slow ashing: There was current overloading
16 Buzzering
17 Power Outlet Indicating Light
Panel Operation
The rst mode of LCD is total current, switching with the Switch/Set
button to show the regular sequence of total current, max. current and
IP shown below:
0.0
0.0
192
168
010
001
Total Current
IP Display
IP Display Max. Current
IP Display IP Display
■ Alarm and IP indicating light
will not flash.
■ IP indicating light is flashing
because of overload.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light remaining lit.
■ IP indicating light is flashing.
1
33
33
2
 1LCD menu shows the total current. èHold the Switch/Set button
for 3 seconds with a long beep to enter alarm current setting. è
Press the Switch/Set button to increase the alarm current by 0.5A
in each press. èHold the Switch/Set button for 3seconds with a
“beep” to save the setting.
 2Press the Switch/Set button and shows the maximum current.
èHold the Switch/Set button for 3seconds with a long beep to
adjust to a zero point.
 3Press the Switch/Set button to switch the display of each IP
address.
IPM-8220
Rear Panel :
1
3
45 6 7 8 9
2
Front Panel :
14
10 11 12 13
1516
1
System Indicating Light
Slow ashing: Normal operating
Rapid ashing: Normal updating
2Reset and Warning Indicating Light
3Temperature/Humidity Port for IPM-ESB Connection
IPM-4220/IPM-8220
Quick Installation Guide
IP-based 4-/8-port Switched
Power Manager

– 5 – –6 –
– 7 – – 8 –
 
3Press the Set button to show "maximal power outlet current
record", èHold the Set button for 3 seconds with a long beep to
adjust to a zero point.

4Hold the Switch button for 3 seconds with a long beep in Port
1~8 mode. èEnter Power On/Off mode ("L" will be added in
front of the original line number). èDouble-click the Set button to
switch between power on and off.
L01
IP Panel Operation
Press the Switch button to show words like "IP" èPress the Set
button to switch the display of each IP address. IP can only be set by
the web page rather than the LCD panel.
192 168 001 020IP
4. Utility Installation for Windows
PLANET “IP Search” is a software utility used to search the Switched
IPM product on a network quickly and with ease.
Step 1: Download the Power Packet Utility from PLANET download URL
http://www.planet.com.tw/en/support/download.php?type1=102
&model=48843&type=8184#list
Step 2: Please press the “Refresh” button to nd out your Switched
IPM.
Step 3: Enter the IP address and login to the homepage of Switched
IPM.
5. Further Information
The above steps introduce the simple installation of the Switched IPM.
For further details on the installation of the Switched IP Power Manager,
please refer to the user manual which you can be downloaded from the
PLANET website.
http://www.planet.com.tw/en/support/download.php?type1=102&model=
48843&type=3
If you have further questions, please contact the local dealer or
distributor where you purchased this product or you can contact PLANET
directly at the following email address: [e-mail]
PLANET Technology Corp.
11F., No. 96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
2011-F10120-000
4Reset Button
5RJ45 Ethernet Port
6USB Connected Port (Future Feature)
7
COM2/1
2 Com Ports provided to enable terminal control, API control and
2 mutual cascading
8Circuit Breaker Protection
9Power Inlet
10 Power Outlet
Note: The maximum output current is 16 amps.
11 LCD Panel
To display total current, branch 1, branch 2, voltage and IP
12
Switch Button
Provide LCD panel in order to switch the total current, power
switch control and IP
13
Set Button
Provide LCD panel in order to switch the total current, branch
current, voltage, power switch current, power switch control and
IP; set alarm current
14 Buzzer
15
Alarm Indicating Light
Lights remaining lit: Alarm has occurred
Slow ashing: There was current overloading
16 Power Outlet Indicating Light
Current Panel Operation
When the LCD panel only displays gures and the sign of "A (AMP)", it
means total current. Switch with the Set button to show the following
sequence:
Total Current
Branch 2
Max. Current
Max. Current
Branch 1 Current
Branch 1 Max. Current
Branch 2 Current
Voltage
0.0A
112V
0.0A
0.0A
0.0A0.0A
0.0A
1
33
2
11
3
 
1LCD menu shows total current, and current values of branch 1 and
branch 2. èHold the Set button for 3 seconds with a long beep
to enter alarm current setting. èEnter ash mode (LCD will ash
after entering setting mode, "S" and "W" will display at the bottom
of LCD). èPress the Set button to increase the alarm current by
0.5A in each press. èHold the Set button for 3 seconds with a
"beep" to save the setting.
 
2Press the Set button to show the voltage information.
 
3Press the Set button to show the maximum current record of all
branch/branch 1/branch 2. èHold the Set button for 3 seconds
with a long beep to adjust to a zero point.
Power Outlet Panel Operation
When the LCD panel shows gures and "0", the information shown
is the branch circuit power outlet. By clicking the Set button, the
following information will be displayed in sequence:
01 0.0A
Port 1 Port 1 Current Port 1 Max. Current
0.0A
1 4
3
2

1Press the Switch button to Port 1~8 mode.
 2Press the Set button to show power outlet current. èHold the
Set button for 3 seconds with a long beep to enter power outlet
alarm current setting. èEnter ash mode (LCD will ash after
entering setting mode, "S", "O" and "W" will display at the bottom
of LCD). èPress the Set button to increase the alarm current by
0.5A in each press. èHold the Set button for 3 seconds with a
"beep" to save the setting.

– 5 – –6 –
– 7 – – 8 –
 
3Press the Set button to show "maximal power outlet current
record", èHold the Set button for 3 seconds with a long beep to
adjust to a zero point.

4Hold the Switch button for 3 seconds with a long beep in Port
1~8 mode. èEnter Power On/Off mode ("L" will be added in
front of the original line number). èDouble-click the Set button to
switch between power on and off.
L01
IP Panel Operation
Press the Switch button to show words like "IP" èPress the Set
button to switch the display of each IP address. IP can only be set by
the web page rather than the LCD panel.
192 168 001 020IP
4. Utility Installation for Windows
PLANET “IP Search” is a software utility used to search the Switched
IPM product on a network quickly and with ease.
Step 1: Download the Power Packet Utility from PLANET download URL
http://www.planet.com.tw/en/support/download.php?type1=102
&model=48843&type=8184#list
Step 2: Please press the “Refresh” button to nd out your Switched
IPM.
Step 3: Enter the IP address and login to the homepage of Switched
IPM.
5. Further Information
The above steps introduce the simple installation of the Switched IPM.
For further details on the installation of the Switched IP Power Manager,
please refer to the user manual which you can be downloaded from the
PLANET website.
http://www.planet.com.tw/en/support/download.php?type1=102&model=
48843&type=3
If you have further questions, please contact the local dealer or
distributor where you purchased this product or you can contact PLANET
directly at the following email address: [e-mail]
PLANET Technology Corp.
11F., No. 96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
2011-F10120-000
4Reset Button
5RJ45 Ethernet Port
6USB Connected Port (Future Feature)
7
COM2/1
2 Com Ports provided to enable terminal control, API control and
2 mutual cascading
8Circuit Breaker Protection
9Power Inlet
10 Power Outlet
Note: The maximum output current is 16 amps.
11 LCD Panel
To display total current, branch 1, branch 2, voltage and IP
12
Switch Button
Provide LCD panel in order to switch the total current, power
switch control and IP
13
Set Button
Provide LCD panel in order to switch the total current, branch
current, voltage, power switch current, power switch control and
IP; set alarm current
14 Buzzer
15
Alarm Indicating Light
Lights remaining lit: Alarm has occurred
Slow ashing: There was current overloading
16 Power Outlet Indicating Light
Current Panel Operation
When the LCD panel only displays gures and the sign of "A (AMP)", it
means total current. Switch with the Set button to show the following
sequence:
Total Current
Branch 2
Max. Current
Max. Current
Branch 1 Current
Branch 1 Max. Current
Branch 2 Current
Voltage
0.0A
112V
0.0A
0.0A
0.0A0.0A
0.0A
1
33
2
11
3
 
1LCD menu shows total current, and current values of branch 1 and
branch 2. èHold the Set button for 3 seconds with a long beep
to enter alarm current setting. èEnter ash mode (LCD will ash
after entering setting mode, "S" and "W" will display at the bottom
of LCD). èPress the Set button to increase the alarm current by
0.5A in each press. èHold the Set button for 3 seconds with a
"beep" to save the setting.
 
2Press the Set button to show the voltage information.
 
3Press the Set button to show the maximum current record of all
branch/branch 1/branch 2. èHold the Set button for 3 seconds
with a long beep to adjust to a zero point.
Power Outlet Panel Operation
When the LCD panel shows gures and "0", the information shown
is the branch circuit power outlet. By clicking the Set button, the
following information will be displayed in sequence:
01 0.0A
Port 1 Port 1 Current Port 1 Max. Current
0.0A
1 4
3
2

1Press the Switch button to Port 1~8 mode.
 2Press the Set button to show power outlet current. èHold the
Set button for 3 seconds with a long beep to enter power outlet
alarm current setting. èEnter ash mode (LCD will ash after
entering setting mode, "S", "O" and "W" will display at the bottom
of LCD). èPress the Set button to increase the alarm current by
0.5A in each press. èHold the Set button for 3 seconds with a
"beep" to save the setting.

– 5 – –6 –
– 7 – – 8 –
 
3Press the Set button to show "maximal power outlet current
record", èHold the Set button for 3 seconds with a long beep to
adjust to a zero point.

4Hold the Switch button for 3 seconds with a long beep in Port
1~8 mode. èEnter Power On/Off mode ("L" will be added in
front of the original line number). èDouble-click the Set button to
switch between power on and off.
L01
IP Panel Operation
Press the Switch button to show words like "IP" èPress the Set
button to switch the display of each IP address. IP can only be set by
the web page rather than the LCD panel.
192 168 001 020IP
4. Utility Installation for Windows
PLANET “IP Search” is a software utility used to search the Switched
IPM product on a network quickly and with ease.
Step 1: Download the Power Packet Utility from PLANET download URL
http://www.planet.com.tw/en/support/download.php?type1=102
&model=48843&type=8184#list
Step 2: Please press the “Refresh” button to nd out your Switched
IPM.
Step 3: Enter the IP address and login to the homepage of Switched
IPM.
5. Further Information
The above steps introduce the simple installation of the Switched IPM.
For further details on the installation of the Switched IP Power Manager,
please refer to the user manual which you can be downloaded from the
PLANET website.
http://www.planet.com.tw/en/support/download.php?type1=102&model=
48843&type=3
If you have further questions, please contact the local dealer or
distributor where you purchased this product or you can contact PLANET
directly at the following email address: [e-mail]
PLANET Technology Corp.
11F., No. 96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
2011-F10120-000
4Reset Button
5RJ45 Ethernet Port
6USB Connected Port (Future Feature)
7
COM2/1
2 Com Ports provided to enable terminal control, API control and
2 mutual cascading
8Circuit Breaker Protection
9Power Inlet
10 Power Outlet
Note: The maximum output current is 16 amps.
11 LCD Panel
To display total current, branch 1, branch 2, voltage and IP
12
Switch Button
Provide LCD panel in order to switch the total current, power
switch control and IP
13
Set Button
Provide LCD panel in order to switch the total current, branch
current, voltage, power switch current, power switch control and
IP; set alarm current
14 Buzzer
15
Alarm Indicating Light
Lights remaining lit: Alarm has occurred
Slow ashing: There was current overloading
16 Power Outlet Indicating Light
Current Panel Operation
When the LCD panel only displays gures and the sign of "A (AMP)", it
means total current. Switch with the Set button to show the following
sequence:
Total Current
Branch 2
Max. Current
Max. Current
Branch 1 Current
Branch 1 Max. Current
Branch 2 Current
Voltage
0.0A
112V
0.0A
0.0A
0.0A0.0A
0.0A
1
33
2
11
3
 
1LCD menu shows total current, and current values of branch 1 and
branch 2. èHold the Set button for 3 seconds with a long beep
to enter alarm current setting. èEnter ash mode (LCD will ash
after entering setting mode, "S" and "W" will display at the bottom
of LCD). èPress the Set button to increase the alarm current by
0.5A in each press. èHold the Set button for 3 seconds with a
"beep" to save the setting.
 
2Press the Set button to show the voltage information.
 
3Press the Set button to show the maximum current record of all
branch/branch 1/branch 2. èHold the Set button for 3 seconds
with a long beep to adjust to a zero point.
Power Outlet Panel Operation
When the LCD panel shows gures and "0", the information shown
is the branch circuit power outlet. By clicking the Set button, the
following information will be displayed in sequence:
01 0.0A
Port 1 Port 1 Current Port 1 Max. Current
0.0A
1 4
3
2

1Press the Switch button to Port 1~8 mode.
 2Press the Set button to show power outlet current. èHold the
Set button for 3 seconds with a long beep to enter power outlet
alarm current setting. èEnter ash mode (LCD will ash after
entering setting mode, "S", "O" and "W" will display at the bottom
of LCD). èPress the Set button to increase the alarm current by
0.5A in each press. èHold the Set button for 3 seconds with a
"beep" to save the setting.

– 5 – –6 –
– 7 – – 8 –
 
3Press the Set button to show "maximal power outlet current
record", èHold the Set button for 3 seconds with a long beep to
adjust to a zero point.

4Hold the Switch button for 3 seconds with a long beep in Port
1~8 mode. èEnter Power On/Off mode ("L" will be added in
front of the original line number). èDouble-click the Set button to
switch between power on and off.
L01
IP Panel Operation
Press the Switch button to show words like "IP" èPress the Set
button to switch the display of each IP address. IP can only be set by
the web page rather than the LCD panel.
192 168 001 020IP
4. Utility Installation for Windows
PLANET “IP Search” is a software utility used to search the Switched
IPM product on a network quickly and with ease.
Step 1: Download the Power Packet Utility from PLANET download URL
http://www.planet.com.tw/en/support/download.php?type1=102
&model=48843&type=8184#list
Step 2: Please press the “Refresh” button to nd out your Switched
IPM.
Step 3: Enter the IP address and login to the homepage of Switched
IPM.
5. Further Information
The above steps introduce the simple installation of the Switched IPM.
For further details on the installation of the Switched IP Power Manager,
please refer to the user manual which you can be downloaded from the
PLANET website.
http://www.planet.com.tw/en/support/download.php?type1=102&model=
48843&type=3
If you have further questions, please contact the local dealer or
distributor where you purchased this product or you can contact PLANET
directly at the following email address: [email protected]
PLANET Technology Corp.
11F., No. 96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
2011-F10120-000
4Reset Button
5RJ45 Ethernet Port
6USB Connected Port (Future Feature)
7
COM2/1
2 Com Ports provided to enable terminal control, API control and
2 mutual cascading
8Circuit Breaker Protection
9Power Inlet
10 Power Outlet
Note: The maximum output current is 16 amps.
11 LCD Panel
To display total current, branch 1, branch 2, voltage and IP
12
Switch Button
Provide LCD panel in order to switch the total current, power
switch control and IP
13
Set Button
Provide LCD panel in order to switch the total current, branch
current, voltage, power switch current, power switch control and
IP; set alarm current
14 Buzzer
15
Alarm Indicating Light
Lights remaining lit: Alarm has occurred
Slow ashing: There was current overloading
16 Power Outlet Indicating Light
Current Panel Operation
When the LCD panel only displays gures and the sign of "A (AMP)", it
means total current. Switch with the Set button to show the following
sequence:
Total Current
Branch 2
Max. Current
Max. Current
Branch 1 Current
Branch 1 Max. Current
Branch 2 Current
Voltage
0.0A
112V
0.0A
0.0A
0.0A0.0A
0.0A
1
33
2
11
3
 
1LCD menu shows total current, and current values of branch 1 and
branch 2. èHold the Set button for 3 seconds with a long beep
to enter alarm current setting. èEnter ash mode (LCD will ash
after entering setting mode, "S" and "W" will display at the bottom
of LCD). èPress the Set button to increase the alarm current by
0.5A in each press. èHold the Set button for 3 seconds with a
"beep" to save the setting.
 
2Press the Set button to show the voltage information.
 
3Press the Set button to show the maximum current record of all
branch/branch 1/branch 2. èHold the Set button for 3 seconds
with a long beep to adjust to a zero point.
Power Outlet Panel Operation
When the LCD panel shows gures and "0", the information shown
is the branch circuit power outlet. By clicking the Set button, the
following information will be displayed in sequence:
01 0.0A
Port 1 Port 1 Current Port 1 Max. Current
0.0A
1 4
3
2

1Press the Switch button to Port 1~8 mode.
 2Press the Set button to show power outlet current. èHold the
Set button for 3 seconds with a long beep to enter power outlet
alarm current setting. èEnter ash mode (LCD will ash after
entering setting mode, "S", "O" and "W" will display at the bottom
of LCD). èPress the Set button to increase the alarm current by
0.5A in each press. èHold the Set button for 3 seconds with a
"beep" to save the setting.