Planet ICA-HM132 User manual

2 Mega-Pixel Wired / Wireless IP Camera
ICA-HM132 / ICA-HM136
ICA-HM316 / ICA-HM316W / ICA-3250V
Quick Installation Guide

Table of Contents
Chapter 1. Introduction................................................................................... 3
1.1 Before Installation ............................................................................... 3
1.2 System Requirements.......................................................................... 3
Chapter 2. Physical Description and Installation................................................. 4
2.1 ICA-HM132 2 Mega-Pixel 20M IR Vari-Focal Dome IP Camera ................. 4
2.1.1 ICA-HM132 Package Content....................................................... 4
2.1.2 ICA-HM132 Physical Details......................................................... 4
2.1.3 ICA-HM132 Installation............................................................... 5
2.2 ICA-HM136 2 Mega-Pixel 20M IR Vandal Proof Dome IP Camera ............. 6
2.2.1 ICA-HM136 Package Content....................................................... 6
2.2.2 ICA-HM136 Physical Details......................................................... 6
2.2.3 ICA-HM136 I/O Control Instruction .............................................. 7
2.2.4 ICA-HM136 Installation............................................................... 8
2.3 ICA-HM316 2 Mega-Pixel Outdoor IR PoE IP Camera .............................. 9
2.3.1 ICA-HM316 Package Content....................................................... 9
2.3.2 ICA-HM316 Physical Details......................................................... 9
2.3.3 ICA-HM316 Installation..............................................................10
2.4 ICA-HM316W 2 Mega-Pixel 11n Outdoor IR IP Camera ..........................11
2.4.1 ICA-HM316W Package Content...................................................11
2.4.2 ICA-HM316W Physical Details.....................................................11
2.4.3 ICA-HM316W Installation ...........................................................12
2.5 ICA-3250V Full HD Outdoor IR PoE IP Camera......................................13
2.5.1 ICA-3250V Package Content.......................................................13
2.5.2 ICA-3250V Physical Details.........................................................13
2.5.3 ICA-3250V Installation...............................................................14
Chapter 3. Camera Windows Utility .................................................................16
3.1 IP Assignment....................................................................................16
Further Information ........................................................................................20

3
Chapter 1. Introduction
Thank you for purchasing the PLANET 2 Mega-Pixel Wired / Wireless IP Camera. It
is versatile and high image solution of surveillance application for day and night.
The video can be stored in the SD card and playback remotely (For ICA-HM132 /
ICA-HM136 / ICA-3250V only). With user friendly interface, it is an easy-to-use IP
camera which is designed for security application.
The PLANET IP Camera support Multi-Prole function can stands for simultaneously
video streams. These Network Cameras can generate H.264, MPEG-4 and M-JPEG
streaming simultaneously to different clients. Moreover, the resolution can be
different from one client to another. This state-of-art design is considerable to t in
various network environments.
1.1 Before Installation
Before installation, please be sure to read this quick installation guide and user’s
manual (CD) carefully to complete machine installation. This guide shows how to
quick set up the cameras, unless model name specied terms “IP Camera” will be
used for these models.
1.2 System Requirements
CPU Intel Core i3-530
RAM 2048MB
Graphic card 512MB
Display Resolution 1920 x 1200
Operating System Windows 2000, XP, 2003, Vista 32bit, Win7 32bit
Network Ethernet 10/100 Base-T

4
Chapter 2. Physical Description and Installation
2.1 ICA-HM132 2 Mega-Pixel 20M IR Vari-Focal Dome IP Camera
2.1.1 ICA-HM132 Package Content
IP Camera Unit x 1
Power Adapter x 1
Screw package x 1
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
2.1.2 ICA-HM132 Physical Details
1. RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This
Ethernet port built N-Way protocol can detect or negotiate the transmission
speed of the network automatically. Please use CAT-5 cable to connect the
Network Camera to a 100Mbps Fast Ethernet network switch or hub.
DC 12V / 1A
I/O Terminal
Video Output
Microphone Input (Pink)
Line Out (Green)
Network
2. I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering, alarm notications. It provides the interface to I/O Terminal.
3. Digital Input (GND+Alarm)
An alarm input for connecting devices that can toggle between an open and
closed circuit, for example: PIRs, door/window contacts, glass break detectors,
etc. When a signal is received the state changes and the input becomes active.

5
4. Relay output (COM+N.O.) / (COM+N.C.)
An output to relay switch, for example: LEDs, Sirens, etc.
5. Digital Input/Alarm Input
1) GND (Ground): Initial state is LOW
2) Alarm: Max. 50mA, DC 3.3V
6. Relay Output
1) N.C. (Normally Close): Max. 1A, 24VDC or 0.2A, 110~240VAC
2) COM: (Common)
3) N.O. (Normally Open): Max. 1A, 24VDC or 0.2A, 110~240VAC
7. Power Jack
The input power is DC 12V.
Note
To ensure maximum compatibility, use only the power adapter that
came with your product. Otherwise, the product may be damaged.
8. MIC in (audio in)
Connect a microphone to the network camera.
9. Line out (audio out)
Connect a loud speaker to the network camera. This is for voice alerting and
two-way audio.
2.1.3 ICA-HM132 Installation
1. Fix IR camera to desired location with stand.
2. Plug-in Ethernet Cable into RJ-45 connector (LAN port).
3. Connect the attached power adapter to camera and plug-in this adapter into
power outlet.
4. Connect Video BNC connector to a TV set if necessary (to check camera viewing
angle and focus).
5. Done.

6
2.2 ICA-HM136 2 Mega-Pixel 20M IR Vandal Proof Dome IP
Camera
2.2.1 ICA-HM136 Package Content
Camera unit x 1
Power Adapter x 1
Accessories Kit x 1
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
2.2.2 ICA-HM136 Physical Details
1. RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This
Ethernet port built N-Way protocol can detect or negotiate the transmission
speed of the network automatically. Please use CAT-5 cable to connect the
Network Camera to a 100Mbps Fast Ethernet network switch or hub.
2. Power Jack: The input power is DC 12V.
Power Jack RJ-45
Note
1. To ensure maximum compatibility, use only the power adapter
that came with your product. Otherwise, the product may be
damaged.
2. The RJ-45 port also supports IEEE 802.3af Power over Ethernet,
apply either PoE or DC power to empower the IP camera and do
not use any other non-standard PoE injector to the camera.

7
2.2.3 ICA-HM136 I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering.
1. Digital Input: (GND+Alarm)
An alarm input for connecting devices that can toggle between an open and
closed circuit, for example: PIRs, door/window contacts, glass break detectors,
etc. When a signal is received the state changes and the input becomes active.
2. Relay output: (COM+N.O.) / (COM+N.C.)
An output to relay switch, for example: LEDs, Sirens, etc.
3. Digital Input/Alarm Input:
1) GND (Ground): Initial state is LOW
2) Alarm: Max. 50mA, DC 3.3V
4. Relay Output:
1) N.C. (Normally Close): Max. 1A, 24VDC or 0.2A, 110~240VAC
2) COM: (Common)
3) N.O. (Normally Open): Max. 1A, 24VDC or 0.2A, 110~240VAC
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
RELAY OUT
ALARM IN
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
Door/Window
Contacts IN
5. Relay Connection:
1) Digital Input connection
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
RELAY OUT
ALARM IN
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
Door/Window
Contacts IN

8
2) Relay Output Connection
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
RELAY OUT
ALARM IN
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
Door/Window
Contacts IN
Or
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
RELAY OUT
ALARM IN
N.O
COM
N.C
GND
ALARM IN
AUDIO OUT
MIC IN
GND
VIDEO OUT
Door/Window
Contacts IN
6. MIC_IN:
Connect a microphone to the network camera.
7. AUDIO_OUT
Connect a loud speaker to the network camera. This is for voice alerting and
two-way audio.
2.2.4 ICA-HM136 Installation
1. Fix IR camera to desired location with stand.
2. Plug-in Ethernet Cable into RJ-45 connector (LAN port).
3. Connect the attached power adapter to camera and plug-in this adapter into
power outlet.
4. Connect Video BNC connector to a TV set if necessary (to check camera viewing
angle and focus).
5. Done.

9
2.3 ICA-HM316 2 Mega-Pixel Outdoor IR PoE IP Camera
2.3.1 ICA-HM316 Package Content
IP Camera Unit x 1
Power Adapter x 1
Screw Package x 1
Stand x 1
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
2.3.2 ICA-HM316 Physical Details
1. RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This
Ethernet port built N-Way protocol can detect or negotiate the transmission
speed of the network automatically. Please use CAT-5 cable to connect the
Network Camera to a 100Mbps Fast Ethernet network switch or hub.
DC 12V / 1A
I/O Terminal
Video Output
Microphone Input (Pink)
Line Out (Green)
Network
2. I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering, alarm notications. It provides the interface to I/O Terminal.
3. Digital Input (GND+Alarm)
An alarm input for connecting devices that can toggle between an open and
closed circuit, for example: PIRs, door/window contacts, glass break detectors,
etc. When a signal is received the state changes and the input becomes active.

10
4. Relay output (COM+N.O.) / (COM+N.C.)
An output to relay switch, for example: LEDs, Sirens, etc.
5. Digital Input/Alarm Input
1) GND (Ground): Initial state is LOW
2) Alarm: Max. 50mA, DC 3.3V
6. Relay Output
1) N.C. (Normally Close): Max. 1A, 24VDC or 0.2A, 110~240VAC
2) COM: (Common)
3) N.O. (Normally Open): Max. 1A, 24VDC or 0.2A, 110~240VAC
7. Power Jack
The input power is DC 12V.
Note
To ensure maximum compatibility, use only the power adapter that
came with your product. Otherwise, the product may be damaged.
8. MIC in (audio in)
Connect a microphone to the network camera.
9. Line out (audio out)
Connect a loud speaker to the network camera. This is for voice alerting and
two-way audio.
2.3.3 ICA-HM316 Installation
1. Fix IR camera to desired location with stand.
2. Plug-in Ethernet Cable into RJ45 connector (LAN port).
3. Connect the attached power adapter to camera and plug-in this adapter into
power outlet.
4. Connect Video BNC connector to a TV set if necessary (to check camera viewing
angle and focus).
5. Done.

11
2.4 ICA-HM316W 2 Mega-Pixel 11n Outdoor IR IP Camera
2.4.1 ICA-HM316W Package Content
IP Camera Unit x 1
Power Adapter x 1
Screw package x 1
Stand x 1
5dbi Antenna x 1
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
2.4.2 ICA-HM316W Physical Details
1. RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This
Ethernet port built N-Way protocol can detect or negotiate the transmission
speed of the network automatically. Please use CAT-5 cable to connect the
Network Camera to a 100Mbps Fast Ethernet network switch or hub.
DC 12V / 1A
I/O Terminal
Video Output
Microphone Input (Pink)
Line Out (Green)
Network
2. I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering, alarm notications. It provides the interface to I/O Terminal.
3. Digital Input (GND+Alarm)
An alarm input for connecting devices that can toggle between an open and
closed circuit, for example: PIRs, door/window contacts, glass break detectors,
etc. When a signal is received the state changes and the input becomes active.

12
4. Relay output (COM+N.O.) / (COM+N.C.)
An output to relay switch, for example: LEDs, Sirens, etc.
5. Digital Input/Alarm Input
1) GND (Ground): Initial state is LOW
2) Alarm: Max. 50mA, DC 3.3V
6. Relay Output
1) N.C. (Normally Close): Max. 1A, 24VDC or 0.2A, 110~240VAC
2) COM: (Common)
3) N.O. (Normally Open): Max. 1A, 24VDC or 0.2A, 110~240VAC
7. Power Jack
The input power is DC 12V.
Note
To ensure maximum compatibility, use only the power adapter that
came with your product. Otherwise, the product may be damaged.
8. MIC in (audio in)
Connect a microphone to the network camera.
9. Line out (audio out)
Connect a loud speaker to the network camera. This is for voice alerting and
two-way audio.
2.4.3 ICA-HM316W Installation
1. Fix IR camera to desired location with stand.
2. Plug-in Ethernet Cable into RJ45 connector (LAN port).
3. Connect the attached power adapter to camera and plug-in this adapter into
power outlet.
4. Connect Video BNC connector to a TV set if necessary (to check camera viewing
angle and focus).
5. Done.

13
2.5 ICA-3250V Full HD Outdoor IR PoE IP Camera
2.5.1 ICA-3250V Package Content
IP Camera Unit x 1
Power Adapter x 1
Screw Package x 1
Female to Female RJ-45 connector x 1
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
2.5.2 ICA-3250V Physical Details
1. RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling. This
Ethernet port built N-Way protocol can detect or negotiate the transmission
speed of the network automatically. Please use CAT-5 cable to connect the
Network Camera to a 100Mbps Fast Ethernet network switch or hub.
I/O Terminal
DC 12V / 1A
Line Out (Green)
Microphone Input (Pink)
Network
Video Output
2. I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering, alarm notications. It provides the interface to I/O Terminal.
3. Digital Input/Output
1) GND (Ground): Initial state is LOW
2) DI (Digital Input): Max. 50mA, DC 5V
3) DO (Digital Output): DC 5V

14
4. Power Jack
The input power is DC 12V.
Note
To ensure maximum compatibility, use only the power adapter that
came with your product. Otherwise, the product may be damaged.
5. MIC in (audio in)
Connect a microphone to the network camera.
6. Line out (audio out)
Connect a loud speaker to the network camera. This is for voice alerting and
two-way audio.
7. Reset to default
Take an electronic wire, plug one side of the wire into "Default" and the other
side into "GND".
2.5.3 ICA-3250V Installation
1. You can use 3-Axis bracket to adjust the angle of camera. Please lock the screws
tightly to x the angle after adjusting.
ROTATION:360˚
TILT:180˚
PAN:360˚
Note
Please notice cable situation, avoid excessive distortions in the
cable, otherwise it will cause malfunction.
2. Plug-in Ethernet Cable into RJ45 connector (LAN port).
3. Connect the attached power adapter to camera and plug-in this adapter into
power outlet.

15
4. Connect Video BNC connector to a TV set if necessary (to check camera viewing
angle and focus).
5. This IP camera is equipped with an external vari-focal lens controller. Please
adjust "ZOOM" and then "FOCUS" as following picture until the image gets clear.
ZOOM FOCUS
6. For the waterproof reason, if you install a Micro SD card, please turn and lock
the screws on the Micro SD card lid tightly and make sure it's sealed.
Screw them tightly
Note
Be aware the waterproof rubber, improper placement or missing the
rubber will cause seal malfunction.
7. Done.

16
Chapter 3. Camera Windows Utility
This chapter shows how to quick set up your H.264 IP Camera. The H.264 IP
Camera is with the default settings. However to help you nd the networked
camera quickly the windows utility (PLANET IP Installer) can search the cameras in
the network that shall help you to congure some basic setting before you started
advanced management and monitoring.
Please insert the bundle CD disk into your CD/DVD-ROM drive. When the welcome
web page appears, please click your IP camera name on the IP camera list. Then
click the PLANET IPInstaller hyperlink to start the PLANET IP Installer.
3.1 IP Assignment
1. Use “IP Installer II” to assign an IP address of IP CAMERA.
The IP Installer software is in the attached CD.
2. IP Installer supports languages.
IPInstallerEng.exe
3.OS: Windows XP SP2 or above. If the following “Windows Security
Alert” popup, please click “Unblock”.

17
4. The GUI of IP Installer is as follows (Default IP: 192.168.0.20).
IP Installer will search all IP Cameras connected on LAN. The user can click
“Search Device” to search again.
Click one of IP Cameras listed on the left side of IP Installer, then the network
conguration of that IP Camera will be listed on the right side. If parameters
changed, click on “Submit”. Then, the network conguration will be changed.
Just click “OK” to reboot.
Please make sure the subnet of PC IP address and IP CAM IP address are the
same.
For Example:
IP CAM IP address: 192.168.0.20
PC IP address: 192.168.0.100

18
To Change PC IP addresses:
Control Panel Network Connections Local Area Connection Properties 
Internet Protocol (TCP/IP) Properties
Please make sure your IP Camera and PC have the same Subnet. If not, please
change IP Camera IP subnet or PC IP subnet accordingly.
A quick way to access remote monitoring is to left-click the mouse twice on a
selected IP Camera listed on “Device list” of IP Installer. An IE browser will be
opened.
Then, please key in the default “Username: admin” and “Password: admin”
in the following message box.

19
If the user name and password are input correctly, the following web page will
be displayed.

20
Further Information
This guide is used to help you startup your IP Camera settings. It is also
recommended to check the user manual in CD disk for more details of the system
and user conguration.