Planet BM-2010 User manual

Bandwidth Manager
BM-2010 / BM-2100
User s Manual

BM-2010 /BM-2100Bandwidth Manager User sManual
Copyright
Copyright (C) 2003 PLANETTechnology Corp. All rights reserved.
The productsand programs described in this User s Manual are licensed productsof PLANETTechnology,This User s
Manual contains proprietary information protected by copyright, and this User s Manual and all accompanying hardware,
software, and documentation are copyrighted.
No part of this User s Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic medium
or machine-readable form by any means by electronic ormechanical.Including photocopying, recording, or information
storage and retrieval systems, for any purpose other than the purchaser's personal use, and without the prior express
written permission of PLANETTechnology.
Disclaimer
PLANETTechnology does not warrant that the hardware will work properly in all environments and applications, and
makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANEThas made every effort to ensure that this User s Manual is accurate; PLANETdisclaims liability for any
inaccuracies or omissions thatmay have occurred.
Information in this User s Manual is subjectto change without notice and does not represent a commitment on the part of
PLANET. PLANETassumes no responsibility for any inaccuracies that may be contained in this User s Manual. PLANET
makes no commitment to update or keep currentthe information in this User s Manual, and reserves the right to make
improvements to this User s Manual and/or to the products described in this User s Manual,at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, wewould appreciate your commentsand
suggestions.
CE mark Warning
This is aclass Adevice, Inadomestic environment, this product may cause radio interference, in which case the user may
be required to take adequate measures.
Trademarks
The PLANETlogo is a trademark ofPLANETTechnology.
This documentation may refer to numerous hardware and software productsby their trade names. In most,if not all cases,
these designations are claimed as trademarks or registered trademarks by their respective companies.
Customer Service
For information on customer service and support for the Bandwidth Manager, please refer to the following Website URL
http://www.planet.com.tw
Before contacting customer service, please take a moment to gatherthe following information
¨ Bandwidth Manager serial number and MAC address
¨ Any error messages that displayed when the problem occurred
¨ Any software running when the problem occurred
¨ Steps you took to resolve the problem on your own
Revision
User s Manual for PLANETBM-2010 / BM-2100
Model: BM-2010 / BM-2100
Rev: 1.0 (May, 2003)
Part No. EM-BM2010

BM-2010 /BM-2100Bandwidth Manager User sManual
Table of Contents
CHAPTER 1 INTRODUCTION........................................................................................................................1
1.1 FEATURES .................................................................................................................................................1
1.2 PACKAGE CONTENTS..................................................................................................................................2
1.3 BANDWIDTH MANAGER FRONT VIEW ...........................................................................................................3
1.4 BANDWIDTH MANAGER REAR PANEL ...........................................................................................................4
1.5 SPECIFICATION...........................................................................................................................................5
CHAPTER 2 HARDWARE INSTALLATION...................................................................................................6
2.1 INSTALLATION REQUIREMENTS ....................................................................................................................6
2.2 INSTALL BANDWIDTH MANAGERTO YOUR NETWORK ....................................................................................6
CHAPTER 3 GETTING STARTED.................................................................................................................8
3.1 INITIAL SETUPBY LCD PANEL .....................................................................................................................8
3.2 LOGGING IN AS ADMINISTRATOR ..................................................................................................................9
CHAPTER 4 WEB CONFIGURATION..........................................................................................................10
4.1 SYSTEM SETTINGS ...................................................................................................................................10
4.1.1Information......................................................................................................................................10
4.1.2Network..........................................................................................................................................11
4.1.3Bandwidth.......................................................................................................................................11
4.1.4Date/Time.......................................................................................................................................12
4.1.5Host................................................................................................................................................12
4.1.6Service............................................................................................................................................14
4.1.7SNMP.............................................................................................................................................15
4.1.8Backup/Restore..............................................................................................................................16
4.1.9Firmware Upgrade..........................................................................................................................17
4.1.10Account.........................................................................................................................................18
4.1.11 Reboot..........................................................................................................................................18
4.1.12 Logout...........................................................................................................................................19
4.2 POLICY EDITOR........................................................................................................................................20
4.2.1Policy Editor....................................................................................................................................20
4.2.2Protection.......................................................................................................................................22
4.2.3IP/MAC BindingSetting..................................................................................................................23
4.2.4IP/MAC Table..................................................................................................................................23
4.2.5Discover IP/MAC............................................................................................................................24
4.2.6Export/ Import................................................................................................................................25
4.2.7 Access ControlSetting...................................................................................................................26
4.2.8 Access List......................................................................................................................................26

BM-2010 /BM-2100Bandwidth Manager User sManual
4.3 REPORT...................................................................................................................................................28
4.3.1Connection.....................................................................................................................................28
4.3.2Internal Host...................................................................................................................................28
4.3.3Service............................................................................................................................................29
4.3.4 Top 10 Host....................................................................................................................................29
4.3.5 Top 10Service................................................................................................................................30
4.3.6Bandwidth Policy............................................................................................................................31
4.3.7Customize.......................................................................................................................................32
4.3.8IPDiscovery - Text List...................................................................................................................33
4.3.9IPDiscovery - Graph List................................................................................................................33
4.3.10 Log Export Log..........................................................................................................................34
4.3.11 Log ToAnalyzer.........................................................................................................................36
CHAPTER 5 BANDWIDTHANALYZER.......................................................................................................37
5.1 INSTALLATION PROCEDURE:......................................................................................................................37
5.2 USING BANDWIDTH ANALYZER ..................................................................................................................37

BM-2010 /BM-2100Bandwidth Manager User sManual
- 1 -
Chapter 1 Introduction
Business-critical and time-sensitive applications such as VoIPor transaction processing need guaranteed
bandwidth. PLANET snew10Mbpsand100MbpsBandwidth Managers, theBM-2010andBM-2100,offer
networkadministrators aneasyyetpowerful means to allocatenetworkresources basedonbusiness
priorities, andto shape, analyzeandcontrolbandwidthusage. Expensive WANresources are more
effectivelyutilized, avoidingthe need for costlyupgrades while still meeting business priorities.
The PLANET BM-2010 andBM-2100 aresimple to install, withtwo10/100MbpsEthernet port for connecting
to the localnetworkand theWAN router respectively.A16x2 character LCDpanel makes installationand
maintenance easier andmore efficient. For bandwidth management, packetscanbe classified based on IP
address, IP subnet andTCP/UDP port number.The device has more than 20ofthe most common protocols
such as H.323, Oracle, HTTP,FTP,etc. for ease ofdefinition;theadministrator can thendefine policies to
ensure committed and maximumbandwidth levelsfor inbound /outboundtraffic in each class. The
administrator can alsodefine three prioritylevels for each policytoensure that highprioritypacketsreceive
the maximumavailable bandwidth. In addition,each policycan haveascheduledefined for whenthepolicy
is activated or inactivated in increments of5 minutes.
The BM-2010andBM-2100 alsoenableadministrators to effectivelymeasuretraffic on thenetworkand
providecomprehensive graphical reportsabouthowbandwidthis beingused. The administrator canview
each internal host s inboundandoutboundtraffic or each networkservice s inboundandoutboundtraffic. The
BM-2010 and BM-2100also provideagraphicalreportfor either the top ten internal hostsor services that
generate traffic. Afree utility,BandwidthAnalyzer,is also provided to help you makefurther analysis ofthe
bandwidthusage. This reportingsystemhelpsadministrators quicklyunderstandandreallocate bandwidth
usage to an optimized leveland makebest use ofthe limited andexpensive Wide-area networkbandwidth.
For uninterrupted Internet access, the BM-2010andBM-2100 also provideanin-box bypass functiontokeep
your Internet service available.
1.1 Features
¨ 19-inchrack-mount sizewith two10/100MbpsFast Ethernetport for true10Mbps or 100Mbpsinbound
and outbound throughput
¨ LCD panel for initial setup and networkinformation display
¨ Remote configuration through standard web browser with SSLsecurity
¨ Supports SNMPtosimplifymanagement
¨ Transparent operation requires no changes to existingnetworkstructure
¨ Traffic classification basedon IP, IP range/subnet and TCP/UDPport range
¨ Configurable guaranteedand maximumbandwidth with threelevels ofpriorities
¨ Assigns dailyandweeklyaccess schedules to each individual policy
¨ Real time traffic monitoringwith graphical bandwidthusage display
¨ Policybandwidth usagereport andcustomization ofbandwidth usage reports
¨ Afree utility, Bandwidth Analyzer, helpswithfurther bandwidth analysis
¨ All user connections canberecorded and uploadedto an ftp sever for billing or analysis
¨ Simple backup and restore ofconfiguration files with full SSLprotection
¨ Basic firewall functions withaccess control byIP or MAC
¨ IP/MAC discover function finds all hosts on the LAN
¨ In-box bypass architecture ensures uninterrupted traffic floweven in the event of device failure

BM-2010 /BM-2100Bandwidth Manager User sManual
- 2 -
1.2 Package Contents
The following items should be included:
¨ Bandwidth Manager
¨ Power Cord
¨ QuickInstallationGuide
¨ User s Manual andutilityCD
¨ Rackmounting kit
Ifanyofthecontents are missing or damaged, please contact your dealer or distributor immediately.

BM-2010 /BM-2100Bandwidth Manager User sManual
- 3 -
1.3 Bandwidth Manager Front View
-Front View:
Bandwidth Manager
ESCENTER
BM-2100
100ACT
LAN
LNK100ACTLNKPWR
WAN
LCD Panel: Used to make IPsettings, view IPsettings, reboot system, showservice information, reset
passwordand reset all configuration. Italso showtheaveragebandwidth usagefor past 10 seconds whennot
in configuration mode. Checksection “Initial Setup by LCD panel”for detail on IP settings. The following
table shows the button function.
Button Function
(Enter) Used to select or confirmthe selection
(ESC) Used to cancel the selection or backto previous
manual
(▲) Change to previous option or increase the
number.Press longer to increase thenumber by
10.
(▼) Change to next optionor decrease thenumber.
Press longer to decrease the number by10.
LED Panel: Used to showthe systemand connection status. The following table showthe connection LED
definition.
LED Status Meaning
PWR Lit Green Indicates the device is receivingpower
STATUS Lit Red Indicates the device is reading data
frommomery
LNK Lit Green Linkis established on LAN or WAN
port
ACT Blink
Green
Packets are transmitting or receiving
on LAN or WAN port
Lit Green
Indicates the linkoperate on 100Mbps
100
Off Indicates the linkoperate on 10Mbps
LED Panel
LCD Panel

BM-2010 /BM-2100Bandwidth Manager User sManual
- 4 -
1.4 Bandwidth Manager RearPanel
- Rear View:
Console
19200, N, 8, 1
AC line :
100~240V AC
50/60Hz
Port Function
Power This is where you will connect theAC
power cord.100~240VAC is allowed.
On/Off Switch You can turn on/offthis device bythe
switch when the power cord is connected
LANPort
This is where you will connect the RJ-45
line to your local switch or device. This
port is MDI interface
WANPort
This is where you will connect the RJ-45
line to your router or ISP.This port is
MDI interface
Console
This port is reserved for manufacturer use
only
WAN Port
LAN Port
Power
On / Off
Console Port

BM-2010 /BM-2100Bandwidth Manager User sManual
- 5 -
1.5 Specification
Product 10Mbps and 100Mbps Bandwidth Manager
Model BM-2010 BM-2100
Hardware
Connections 2 x 10/100Base-TX
Button Hardware Reset
LCD Panel 16x2 characters LCD
SystemLED System: PWR, STATUS
Network:ACT, LNK,100 for LAN andWAN ports
Power 100~240 VAC, 50~60Hz
Operating Environment Temperature: 5~40°C
Relative Humidity:20%~90%
Dimension Wx D x H 431 x 271 x 44
Regulatory FCC, CE Mark
Software
MaximumBandwidth 10Mbps 100Mbps
MaximumHost catalog+
Service Catalog +Policy
512 1024
Maximumconcurrent
session
65535
Management Web with SSLprotect, SNMP,LCD panel
Traffic Classification IP, IPsubnet, TCP/UDPport
BandwidthAllocation Hierarchyofpolicyrules with In/Outtraffic management
Guaranteed andmaximumbandwidth
Scheduled in unitof5 minutes
3 Priorities
Real-Time Report Number ofConnections
Internal Host In/OutTraffic
Service In/Out Traffic
Top 10 Host
Top 10 Service
All Policies Bandwidth Usage
Customized Bandwidth Usage Report
Advanced Report BandwidthAnalyzer for advanced analysis
Upload each user s connectiondata to FTPsever for
billing or other analysis
Firewall DenySYN /UDP/ ICMPflood, denyport scan
Access control to limit user s access rights based on IP
or TCP/UDPport
Discard per user connection based onIPor MAC
Other Functions Firmware upgradeable through web
NTPsupport
Configuration backup and restore through web
In-box bypass

BM-2010 /BM-2100Bandwidth Manager User sManual
- 6 -
Chapter 2 Hardware Installation
2.1 Installation Requirements
Before installing the BandwidthManager, make sure your networkmeets the followingrequirements.
-Mechanical Requirements
The Bandwidth Manager is to beinstalled betweenyour router and local area network.The Bandwidth
Manager canbe placed on the table or rack. Locate the unit near the power outlet.
- Electrical Requirements
The Bandwidth Manager is powered from100/240 VAC. A standard IEC connector is used for the power
cable.Follow all applicable electrical codes. Frame ground should be tied to a common groundingpoint
using #18AWGcable.
NOTE: The BandwidthManageris apower-requireddevice, itmeans, theBandwidthManager will not
workuntil it is powered. Ifyour networked PCs will need totransmit dataall the time, please
consider use anUPS (Uninterrupted Power Supply)for your Bandwidth Manager.It will prevent
you fromnetworkdataloss.Insomearea,installingasurge suppressiondevicemayalsohelpto
protect your BandwidthManager frombeing damaged byunregulatedsurgeor current tothe
Bandwidth Manager.
- Network Requirements
In order for Bandwidth Manager tomanage traffic, the traffic must pass throughBandwidth Manager at a
useful point in a network. Inmost situations, the bandwidthmanager should be placed behind the Internet
connection router.
This deploymentallowsthenetworkadministers to control all bandwidthbased on business priorities and
give business-critical and time-sensitive applications guarantee bandwidth and higher priority.
Business-critical applications can receivemaximumperformance while other less urgenttraffic is still
available onremainingbandwidth. Bandwidth Manageralso provides comprehensive reportingfunctions to
help monitor networkand bandwidth usage and allowadjustment ofthe bandwidth management policies
accordingly.
The Bandwidth Manager provides two 10/100Base-TXport for connecting to WAN (external) andLAN
(internal) side. The networkports are both MDI (media dependentinterface) port. Please use straight
Category5 UTP Ethernet cable to connect the network port toswitch, hubor otherdevices with MDI-X
interface and usecross-over cableto connect the networkport to router,DSL/Cable modemor other
devices with MDI interface.
2.2 Install Bandwidth Manager to Your Network
- Choose an Installation Site
Select a suitable place on the networkto install the Bandwidth Manager.
- Connect LAN Cables
Use standard LAN cables toconnect your LAN sideSwitch or Hubtothe LAN ports on BandwidthManager.
Both10Base-Tand100Base-Tconnections canbe used. The LANandWAN port ofbandwidthmanager
support Auto-Negotiation to connect withbest speed and duplex mode. The LAN port ofBandwidth
Manager is MDI port. Thus, youcan just use straight networkto connect the LAN port toyour switch or
hub.

BM-2010 /BM-2100Bandwidth Manager User sManual
- 7 -
- Connect WANCable
Connect the router, DSL or Cable modemto the WAN port on Bandwidth Manager.The LAN andWAN port
ofBandwidth Manager areboth MDI port. Thus, in some case, you mayneed to use cross-over cable to
connect your router, DSLor cable modem.
- Power Up
Connect thesuppliedpowercord toBandwidth Manager andusethepowerswitchthat inrear panel to turn
on the Bandwidth Manager.Use onlythepower cord provided. Using adifferent one maycausehardware
damage.
NOTE: Once you power onthe BandwidthManager, it will start to beep indicated it is onby-pass mode.
This is normal and when the systemstop to beep,the systembooting is completed.
- Check the LEDs
The PWRLED shouldbeON. The STATUS LEDshouldflash for about 1to2minutes,thenturnOff.This
LED will also flash when is reading datafromthe memory.Both theWAN and LAN s LNK LED should be
on. Ifone oftheLED is off, please checkthe networkconnection. In some case, you mayneed to use
cross-over cableto connectthe LAN or WAN port to your networks.
For more information, refer to Section 1.3 Bandwidth Manager Front View.

BM-2010 /BM-2100Bandwidth Manager User sManual
- 8 -
Chapter 3 Getting Started
This chapter explains how to setup your computer to be a client to manage the Bandwidth Manager.
3.1 Initial Setup byLCD Panel
1. Press (ENTER) button to enter Select menu.
2. Choose Setup Networkand press (ENTER) button to enter IPsetup process.
3. Set the Bandwidth Manager IPaddress:
Please press (▲) or (▼) button to edit the Bandwidth Manager IPaddress. Press (ENTER)
button toedit next number. After editing all the number, press (ENTER) button to start the
Networkmaskconfiguration.
NOTE: You can press (▲) or (▼) longer for it the number to change in unit of10.
4. Set the Bandwidth Manager subnet mask:
Please press ((▲) or (▼)buttonto edit the BandwidthManager IPaddress. Press (ENTER)
button toedit next number.After editing all thenumber, press (ENTER) button to start the
Gatewayaddress configuration.
5. Set the Bandwidth Manager Gatewayaddress:
Please press (▲) or (▼) button to edit the Bandwidth Manager IPaddress. Press (ENTER)
button toedit next number.After editing all thenumber, press (ENTER) button to save the
configuration.
6. Confirmand Save Configuration:
Ifthe configuration is Ok,please press (ENTER) buttonto save. Otherwise, press (ESC) button to
go backto SELECT Menu.
7. After you press (ENTER), the following message is shown:
。
Nowthe newIPsettings is active and youcan start on web management ofthe Bandwidth
Manager.
Save Config?
Y(Enter) N(ESC)
SELECT:
Setup Network
IP Address:
192.168.1.251
NetmaskAddress:
255.255.255.0
GatewayAddress:
192.168.1.254
Setup Network
Save OK....

BM-2010 /BM-2100Bandwidth Manager User sManual
- 9 -
3.2 Logging in as Administrator
Nowyou can communicatewithBandwidth Manager byweb browser.
Open thewebbrowser andtype https://192.168.0.250:8889.Please notethat “8889”is theport number of
Bandwidth Manager management interface, “https”here is to invoke the SSLof you web browser.
You must keyin user name and password to enter itsweb management interface.
The default user name is “admin”without password.
Then, youwill enter Bandwidth Manager s Configuration Menu.

BM-2010 /BM-2100Bandwidth Manager User sManual
- 10 -
Chapter 4 Web Configuration
This chapter introduces howto configure the Bandwidth Manager to effectivelycontrol your bandwidth usage.
On the top ofthe Web interface, there is three major menu ofthe bandwidth manager:
SystemSettings:The basic systemconfigurations
Policy Editor:The policythat will be usedto manage the bandwidth
Report:The reporting system ofthe bandwidthmanagerbase on the systemsettings and pre-defined
policy
The bandwidth manager will need thethreeparameters before it operates thebandwidth control: Host,
(illustratedin section 4.1.6), Services (illustrated insection 4.1.7) and Policy,(illustratedin section4.2).
However,some ofthe configurations arealsorequired. Please refer to the related section for the details.
4.1 System Settings
Systemsettings menu contains threecategories:“General”allowsyoutoconfigurebasic network
parameters, Internet connection bandwidth and date/time. “Catalog”allowsyouto definehost andservices
information whichis neededfor policyeditor.“Admin”containsoptions tosetupSNMP,backup /restore
settings, upgradefirmware,etc.
4.1.1 Information
This section showsinformationabout the Bandwidth Manager

BM-2010 /BM-2100Bandwidth Manager User sManual
- 11 -
4.1.2 Network
You can setup Bandwidth Manager networksettings in this section.
¨ Host Name: Please assigna name that is easytoremember for Bandwidth Manager.
¨ Domain Name: Your localnetworkdomain name.
¨ DNS Server: Your ISP s DNS server IPor your DNS server IP.
¨ IP Address: Please assign an IPthatis not in use byother device for BandwidthManager.The default
IPaddress ofBandwidth Manager is 192.168.0.250. This IPaddress can be on different subnet from
other internal hosts that youwant to manage. For example, the Bandwidth Manager s IPcan be
192.168.0.250 and you canuse itto manage internal hosts with IP in10.x.x.x subnet.
¨ Network Mask: Your local networksubnet mask.For example, 255.255.255.0.
¨ Default Gateway: Your local networkdefault gateway.For example, 192.168.0.254.
¨ Save: Press save button tosave all these configurations.
Note: If youhave modified the IPaddress to adifferent IPsubnet, you needto also modifytheIP
address ofmanagement client s IPaddress settings.
4.1.3 Bandwidth
Please enter your network bandwidthhere. The sumofguaranteed bandwidthfor all policies should not
exceed this value.
¨ Inbound Bandwidth: Inputthe downstreamspeed ofyour Internet connection (WAN port). The valid
value is form1 to 2048 in units ofkbps.
¨ Outbound Bandwidth: Input the upstreamspeed of your Internet connection(WAN port). The valid
value is form1 to 2048 in units ofkbps.
¨ Save: Press save button tosave all these configurations.
BM-2010 allowsupto10Mbps(10240kbps) and BM-2100allowsup to100Mbps(102400kbps)
inbound/outboundbandwidth in both directions ofitsWANport. Pleasebeaware ofthebandwidththat your
Internetservices provider provided.It is not necessaryto configure Inbound and outboundbandwidthin the
samevalues. Asymmetric bandwidth like1.5Mbps(1544Kbs) downstream,384KbpsupstreamADSLis

BM-2010 /BM-2100Bandwidth Manager User sManual
- 12 -
allowed.
4.1.4 Date/Time
The Date/Timemenu contains commands for setting BandwidthManager's timeand date required for
correctly record the bandwidth usagetime. User candirectly inputthedateand timeor specify theNTP server
for the device tosynchronize with time-server. Clickon “Date/Time”in thesystemsettings menu bar and the
Date/Time screen will appear as illustrated below:
¨ Date: Input the year andselect the Date fromthe pull-downlist respectively.
¨ Time: Select theTime fromthe pull-down list respectively.
¨ NTPServer: Local NTP(Networktime protocol) server IPor DNS name. If you want to manually
configure the date andtime, left this field blank.
Note: Please findbelow NTPserver web address for your referenceto set thetime-server.
http://www.eecis.udel.edu/~mills/ntp/clock1a.htm
http://www.eecis.udel.edu/~mills/ntp/clock2a.htm
¨ Time Zone: Systemadministrator must select the timezone for the region.
¨ Save: Press save button tosave all these configurations. If youhave input a NTPserver IPaddress or
DNS name, the Bandwidth Manager will tryto inquire the current time and update the Date and Time
field.
The Date/Timeinformationwill be used in thereporting system(refer to section 4.3). Ifyour Bandwidth
Manager canreach totheInternet, youcanfindthenearest NTPserver intheInternetfor your Bandwidth
Manager that should provide theaccurate date and time for the bandwidth manager.
4.1.5 Host
Bandwidth Manager cancontrol thebandwidthusagevia host IPaddress. You must define local and/or
remote user sIPaddress that youwantto manage to thehost catalog. This host catalog is useful on
defining policy.The totalnumber ofhost catalog,service catalog and policies cannot exceed 512 for BM-2010
and 1024 for BM-2100.
The Host Catalog pagelists all thedefined hostswithhost name, IPaddress andlocation. On the top ofthe
host table,thefollowing buttons are available:
¨ New - Create newhost catalog.
¨ Prev- Go to previous page.
¨ 1, 2, …- First, second, …page.

BM-2010 /BM-2100Bandwidth Manager User sManual
- 13 -
¨ Next- Next page.
On theActionfieldofeach host name, the following two buttons areprovided:
- Modifythehost catalog
- Delete the host catalog
After clicking “New”or Modifybutton, the following hostconfigurationpagewill be shown:
¨ Host Name: The name ofspecified IPaddress or a range ofIPaddress. With it, you can easilytell the
bandwidthusage throughthis meaningful name. For example, anamelike “Web_server”to adedicated
IP,or “Acct_Group”for the IPrangeofaccounting department.
¨ IP Address: IPor IPrange ofthis host. You can input bysingle IP address, IPrange, IPsubnet or mix
ofabout formats and divided bycomma. For example, 192.168.0.1, 192.168.0.5, for the twodevices
using (IP address 1 and 5); 192.168.0.20-30 (for the range ofIPaddress from20 to 30), and
192.168.0.128/28 (for IPaddress from128 to 143).
¨ Location: Ifthe host s position is on theWAN side ofBandwidth Manager in the network, please choose
external. Ifthe host s position is on the LAN side ofBandwidth Manager, pleasechoose internal.
¨ Monitor: Enable or disableto monitor the traffic flow with this IPor IPrange andshowon the report
function.
¨ Description: Additional description ofthis host(s).
¨ Save/Cancel: Press save button tosave above configurations and Cancel button to discard your
configurations.

BM-2010 /BM-2100Bandwidth Manager User sManual
- 14 -
After clicking Save or Cancel button,the Host Catalogpagewill be shownagain. Toedit the host(s) you
have configured, please click Modifybutton on theAction field. Toremove the host(s) youhave configured,
please clickDelete button on theAction field.
4.1.6 Service
The ServiceCatalogcontains all thepopularservices that youmaywanttomanage. The total number ofhost
catalog, servicecatalog and policiescannotexceed512 for BM-2010and1024for BM-2100. The bandwidth
Manager have contained 22predefine services. For other Internet services, however,youcan direct clickon
Newtoadd the services or clickon Modifyicon to modifyand remove byclickon the delete icon.
¨ New - Create newservice.
¨ Prev- Go to previous page.
¨ 1, 2, …- First, second, …page.
¨ Next- Next page.
On theActionfieldofeach service name, the followingtwo buttons are provided:
- ModifytheServicecatalog
- Delete theService catalog
After clicking “New”or Modifybutton, the following service configuration page will be shown.

BM-2010 /BM-2100Bandwidth Manager User sManual
- 15 -
¨ Name: Name ofthis service. For example, www,http or telnet.
¨ Protocol: Choose whichkind ofprotocol this service use. For example, Telnetis using TCP; voicedata
transmission like PLANET VoIPgateway,is using UDP.
¨ Monitor: Enable or disableto monitor this type oftraffic flowand showon the report function.
¨ Port Number: enter the port number this service use. For example, Telnet will use port 23, http will use
port 80, PLANET VoIPgatewayis using 30000 to30100 bydefault.
¨ Description: Additional description ofthis service.
¨ Save/Cancel: Press save button tosave above configurations and Cancel button to discard your
configurations.
After clicking Save or Cancel button, the ServiceCatalog page will be shownagain. Toedit theservice you
have configured, please click Modifybutton on theAction field.Toremove the serviceyouhave configured,
please clickDelete button on theAction field.
4.1.7 SNMP
Use the SNMPConfiguration screen to displayand modifyparameters for the Simple NetworkManagement
Protocol(SNMP). The device includes an on-board SNMP agent which monitors thestatus ofitshardware, as
well as the traffic passing throughit.Acomputer attached tothe network,called aNetworkManagement
Station(NMS),can be usedto access this information. Access rightsto theagent are controlledby community
string. Tocommunicate withthe device, the NMS must first submit avalid community stringfor authentication.

BM-2010 /BM-2100Bandwidth Manager User sManual
- 16 -
¨ Enable SNMP: Checkthis box to enable the SNMPfunction.
¨ Community Strings: Acommunityentryauthorized for management access. The network
management station must use same string to read theSNMP data fromthe device.
¨ SystemLocation: Specifies the area or location where thedeviceresides.
¨ Contact Information: Contact person for the device.
¨ Save: Press save button tosave all these configurations.
4.1.8 Backup/Restore
You can easilybackup and restore thecurrent configuration ofBandwidth Manager.
¨ Backup: Press “Start”button on the Config Download rowto download the configurationfile of
Bandwidth Manager toyourlocal client side. The followingpagewill then be shown. Click “Save”to
save the configurationfile.
Note: It is stronglyrecommended to backup your fileconfigurationfile whenever you have
complete the configurations.