Planet HPOE-2400G User manual

User’s Manual of HPOE-1200G / HPOE2400G
User’s Manual
HPOE-1200G
HPOE-2400G
IEEE 802.3at
12 / 24-Port Gigabit Power over Ethernet
Managed Injector Hub
1

User’s Manual of HPOE-1200G / HPOE2400G
Trademarks
Copyright ©PLANET Technology Corp. 2011
Contents subject to which revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and
makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the part
of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products described in this User’s Manual, at any time
without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments
and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at whose own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user
may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from the power circuit.
Without removing power cable, the device will still consuming power from the power source. In the view of Saving the
Energy and reduce the unnecessary power consuming, it is strongly suggested to remove the power connection for the
device if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately
Revision
PLANET IEEE 802.3at Power over Gigabit Ethernet Managed Injector Hub User's Manual
FOR MODELS: HPOE-1200G / HPOE-2400G
REVISION: 1.0 (JANUARY.2011)
Part No.: 2080-AF0260-000
2

User’s Manual of HPOE-1200G / HPOE2400G
3
TABLE OF CONTENTS
1. INTRODUCTION .............................................................................................................5
1.1 PACKAGE CONTENTS.................................................................................................................................. 5
1.2 PRODUCT DESCRIPTION.............................................................................................................................. 5
1.3 HOW TO USE THIS MANUAL ........................................................................................................................ 7
1.4 PRODUCT FEATURES .................................................................................................................................. 8
1.5 PRODUCT SPECIFICATIONS ....................................................................................................................... 10
2. INSTALLATION ............................................................................................................12
2.1 HARDWARE DESCRIPTION......................................................................................................................... 12
2.1.1 Injector Front Panel.......................................................................................................................... 12
2.1.2 LED Indicators.................................................................................................................................. 13
2.1.3 Injector Rear Panel .......................................................................................................................... 13
2.2 INSTALLING THE POEINJECTOR HUB......................................................................................................... 14
2.2.1 Desktop Installation.......................................................................................................................... 14
2.2.2 Rack Mounting ................................................................................................................................. 14
2.2.3 Network Application Installation ....................................................................................................... 16
2.2.4 Power over Ethernet Powered Device............................................................................................. 17
3 Management..................................................................................................................18
3.1 OVERVIEW................................................................................................................................................ 18
3.2 REQUIREMENTS........................................................................................................................................ 18
3.3 MANAGEMENT METHOD ............................................................................................................................ 19
3.3.1 Web Management............................................................................................................................ 19
3.3.2 PLANET Smart Discovery Utility...................................................................................................... 20
4 WEB CONFIGURATION................................................................................................22
4.1 MANIN MENU............................................................................................................................................ 22U
4.2 WEB PANEL ............................................................................................................................................. 23
4.3 SYSTEM ................................................................................................................................................... 23
4.3.1 System Information .......................................................................................................................... 24
4.3.2 IP Configuration ............................................................................................................................... 25
4.3.3 NTP Configuration............................................................................................................................ 26
4.3.4 Password Setting ............................................................................................................................. 27
4.3.5 Firmware Upgrade ........................................................................................................................... 28
4.3.6 Configuration Setting........................................................................................................................ 29
4.3.7 Factory Default................................................................................................................................. 32
4.3.8 System Log ...................................................................................................................................... 34
4.3.9 System Reboot................................................................................................................................. 35
4.3.10 Logout ............................................................................................................................................ 35
4.4 SNMP ..................................................................................................................................................... 37

User’s Manual of HPOE-1200G / HPOE2400G
4.4.1 SNMP Management......................................................................................................................... 37
4.5 POWER OVER ETHERNET........................................................................................................................... 39
4.5.1 PoE Configuration ............................................................................................................................ 40
4.5.2 PoE Schedule profile........................................................................................................................ 42
4.5.3 PoE Schedule .................................................................................................................................. 44
4.5.4 PoE Schedule Profile configuration example................................................................................... 45
5. Power OVER Ethernet Overview ................................................................................49
6. The PoE Provision Process........................................................................................52
6.1 LINE DETECTION....................................................................................................................................... 52
6.2 CLASSIFICATION....................................................................................................................................... 52
6.3 START-UP ................................................................................................................................................ 53
6.4 OPERATION.............................................................................................................................................. 53
6.5 POWER DISCONNECTION SCENARIOS ........................................................................................................ 53
APPENDIX A.....................................................................................................................55
A.1 MDI SETTINGS......................................................................................................................................... 55
A.2 POWER DEVICE CLASSIFICATION VALUES.................................................................................................. 55
A.3 DATA OUT POEINJECTOR RJ-45 PORT PIN ASSIGNMENTS .................................................................... 56
4

User’s Manual of HPOE-1200G / HPOE2400G
1. INTRODUCTION
1.1 Package Contents
CHECK THE CONTENTS OF YOUR PACKAGE FOR FOLLOWING PARTS:
● The PoE Injector Hub x 1
● The Quick Installation Guide x 1
● User’s Manual CD x 1
● Power Cord x 1
● Rubber Feet x 4
● Two Rack-mounting brackets with attachment screw x1 (set)
If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the
original packing material, and use them against to repack the product in case there is a need to return it to us for repair.
In the following section, the term “PoE Injector Hub” means the two Gigabit PoE Injector Hub devices, i.e. HPOE-1200G,
HPOE-2400G. Terms with lower case “injector” means any IEEE 802.3at / 802.3af power injectors. “PD” means the
abbreviated from IEEE 802.3at / 802.3af powered device.
1.2 Product Description
The PoE Injector Hub are 12 / 24-Port IEEE 802.3at / 802.3af Power over Ethernet Mid-Span injector hub complies with
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3at and IEEE 802.3af standards. It is equipped with 12 / 24
10/100/1000Mbps Gigabit Ethernet ports that support full 52V DC power for any remote IEEE 802.3at / 802.3af powered
device (PD) like 802.11b/g/n Wireless LAN Access Point, IP phone, LAN Camera or any other network devices. The PoE
Injector Hub should provide the sufficient 30.8 / 15.4 Watts power each port to the 12 / 24 remote PD devices with 460 / 340
Watts power supply.
The PoE Injector Hub is installed between a regular Ethernet switch and the powered devices, injecting power without
affecting the data transmit. It offer a cost effective solution and quickly way to upgrade network system to IEEE 802.3at /
802.3af Power over Ethernet, without replace the existing Ethernet Switch.
There are 24 / 48 RJ-45 STP ports on the front panel of PoE Injector Hub, 12 / 24 of them on lower stack are "Data" ports
and the other 12 / 24 ports on upper stack are "Data + Power output" ports. Each of the "Data + Power output" port on
upper stack functions as an injector which inserts DC Voltage into the CAT 5e/6 cable allowing the cable between the
Injector and Splitter to transfer data and power simultaneously.
To manage your powered devices, the PoE Injector Hub provides both Web management interfaces in which
administrators can manage functions such as port Enable/Disable, port priority, limit, schedule, system configuration,
Username/Password changing and with smart feature for powered device, the PoE Injector Hub can auto detect the power
status on each port and show massages Web management interface. These features also provided a cost-effective way to
manage the devices from Internet whenever you are at work or at home.
5

User’s Manual of HPOE-1200G / HPOE2400G
Power over Ethernet Applications
For the places hard to find the power outlet, the PoE Injector Hub provides the easiest way to power your Ethernet devices
such as PLANET Internet Cameras and outdoor Wireless Access Point installed on the top of the building.
To control the power system of your networking devices, the Gigabit PoE Injector Hub can directly co-work with PoE IP
Phone to build VoIP telephony network in the office. Furthermore, the Gigabit PoE Injector Hub can be directly connected to
any third party 802.3at / 802.3af devices and PoE Switches installed 100 meters away.
Figure 1: PoE Injector Hub Application
6

User’s Manual of HPOE-1200G / HPOE2400G
1.3 How to Use This Manual
This User Manual is structured as follows:
Section 2, Installation
It explains the functions of PoE Injector Hub and how to physically install the PoE Injector Hub.
Section 3, Management
It contains information about the software function of the PoE Injector Hub.
Section 4, Web Configuration
The section explains how to manage the PoE Injector Hub through Web interface.
Section 5, Power over Ethernet overview
The section explains the Power over Ethernet theories.
Section 6, PoE power Provision Process
The section explains the PoE power provision process.
Section 7, Troubleshooting
The section contains troubleshooting guide of the PoE Injector Hub.
Appendix A
It contains cable information of PoE Injector Hub.
7

User’s Manual of HPOE-1200G / HPOE2400G
1.4 Product Features
¾Physical Port
HPOE-1200G
24-Port RJ-45
y12 -Port 10/100/1000Mbps “Data input”
y12 -Port 10/100/1000Mbps “Data + Power output”
1-Port 10/100Base-TX Management Port
Reset button for system management
HPOE-2400G
48-Port RJ-45
y24 -Port 10/100/1000Mbps “Data input”
y24 -Port 10/100/1000Mbps “Data + Power output”
1-Port 10/100Base-TX Management Port
Reset button for system management
¾Power over Ethernet
Complies with IEEE 802.3, IEEE 802.3at and IEEE 802.3af Power over Ethernet Mid-Span PSE
Up to 24 IEEE 802.3at / 802.3af devices powered
Supports PoE power up to 30.8Watts / 15.4 Watts for each PoE ports
Automatically detect powered device (PD)
Circuit protection prevent power interference between ports
Remote power feeding up to 100m
¾PoE Management
Total PoE power budget control
Per port PoE power schedule
PoE function enable / disable
Per port PoE function enable / disable
Per port 802.3at / 802.3af mode switch
PoE port power feeding priority
Per PoE port power limit
PD classification detection
Over Temperature Protection
PoE Temperature Threshold
PoE power Usage Threshold
¾Management
Web interface for remote management
Supports Network Time Protocol (NTP)
Firmware upgrade through Web interface
PLANET Smart Discovery utility automatically finds PLANET devices on the network
SNMP Trap for alarm notification of events
System Log / Remote Syslog
8

User’s Manual of HPOE-1200G / HPOE2400G
¾Hardware
19-inch rack mountable; 1U height
Reset button for reset to default setting and system reboot
LED indicators for PoE ready and PoE activity
LED indicators for Power Alert and Fan Alert
FCC Part 15 Class A, CE
¾Standard Compliance
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3at pre-standard Power over Ethernet
IEEE 802.3af Power over Ethernet
9

User’s Manual of HPOE-1200G / HPOE2400G
1.5 Product Specifications
Product HPOE-1200G HPOE-2400G
Hardware
“Data” Input Ports 12 x RJ-45 24 x RJ-45
“Data+Power” Output Ports 12 x RJ-45 24 x RJ-45
Interface
Management Port 1 x RJ-45; 10/100Base-TX, auto-negotiation, auto-MDI / MDIX
Data Rate 10/100/1000Mbps
LED
System: SYS Power x 1 (Green)
Management Port x2: 10/100
(Green / Orange)
Per PoE Port: PoE in use x 1
(Green)
PoE Fail x 1
FAN Fail x 1
System: SYS Power x 1 (Green)
Management Port x2: 10/100
(Green / Orange)
Per PoE Port: PoE in use x 1
(Green)
PoE1 Fail x 1
PoE2 Fail x 1
FAN1 Fail x 1
FAN2 Fail x 1
Network Cable
10Base-T: 4-Pair UTP Cat. 5 up to 100m (328ft)
100Base-TX: 4-Pair UTP Cat. 5 up to 100m (328ft)
1000Base-T: 4-Pair UTP Cat. 5e, 6, up to 100m (328ft)
EIA/TIA- 568 100-ohm STP (100m)
Dimension (W x D x H) 440 x 300 x 44 mm (1U height)
Weight 4.27kg 5.08kg
Power Requirement 100-240V AC, 50/60 Hz
Power Consumption 370 Watts max. 490 Watts max.
Operating Temperature 0 ~ 50 Degree C
Storage Temperature -10 ~ 70 Degree C
Humidity 5 ~ 95% (Non-condensing)
Cooling Fan x 2 Fan x 3
Power over Ethernet
PoE Power supply Type Mid-Span
PoE Power Output Per Port DC 52V 30.8 / 15.4 Watts
Power Pin Assignment 4/5(+), 7/8(-)
PoE Power Budget 340 Watts 460 Watts
Number of 802.3af PD Class 0, 1, 2,
3 can be powered 12 24
Number of 802.3at PD Class 1, 2, 3
can be powered 12 24
Number of 802.3at PD Class 0, 4
can be powered 10 14
Management
Management Interface Web, PLANET Smart Discovery Lite
PoE Management
Power Limit by Priority and Total Limit
Per port power schedule
Per port power enable/disable
Power feeding priority
Current usage and status
10

User’s Manual of HPOE-1200G / HPOE2400G
Total power consumption
Management Feature
System / Management functions setup
Web firmware upgrade
SNMP Trap for alarm notification of events
Standards Conformance
Standards Compliance
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
Pre-standard IEEE 802.3at Power over Ethernet
IEEE 802.3af Power over Ethernet
Regulation Compliance FCC Part 15 Class A, CE
11

User’s Manual of HPOE-1200G / HPOE2400G
2. INSTALLATION
This section describes the hardware features and installation of these PoE Injector Hub on the desktop or rack mount. For
easier management and control of the PoE Injector Hub familiarize yourself with its display indicators, and ports. Front
panel illustrations in this chapter display the unit LED indicators. Before deploy the PoE Injector Hub, please read this
chapter completely.
2.1 Hardware Description
The section describes the hardware of the PoE Injector Hub and gives a physical and functional overview.
2.1.1 Injector Front Panel
The unit front panel provides a simple interface monitoring the PoE Injector Hub. Figure 2-1-1 & 2-1-2 shows front panel of
the PoE Injector Hub.
Front Panel of HPOE-1200G
Figure 2-1-1: HPOE-1200G front panel
Front Panel of HPOE-2400G
Figure 2-1-2: HPOE-2400G front panel
■ Reset button
At the left of front panel, the reset button is designed for reboot the PoE Injector Hub without turn off and on the power.
Reset Button
Hardware
Figure 2-1-3: Reset button of PoE Injector Hub
12

User’s Manual of HPOE-1200G / HPOE2400G
The following is the summary table of Reset button functions:
Reset Button Pressed and Released Function
About 1 second Reboot the PoE Injector Hub.
About 8 second
Reset the PoE Injector Hub to Factory Default configuration.
The PoE Injector Hub will reboot and load the default IP
settings as below.
Be sure that you backup the current configuration of PoE Injector Hub before reset PoE Injector
Hub; else the entire configuration will be erased when pressing the “RESET” button.
2.1.2 LED Indicators
The front panel LEDs indicates instant status of system power, Management port Link/Active and PoE port links, helps
administrator to monitor and troubleshoot when needed.
LED Color Function
FAN1 Fail Green Lights to indicate FAN1 have been stop.
FAN2 Fail Green Lights to indicate FAN2 have been stop. (Only for HPOE-2400G)
Power1 Fail Green Lights to indicate one of power supply 1 has failure.
Power2 Fail Green Lights to indicate one of power supply 2 has failure. (Only for HPOE-2400G)
Power Green Lights to indicate power on.
PoE In-use Green Lights to indicate that the port is in use and supplying 48V DC power.
2.1.3 Injector Rear Panel
The rear panel of the PoE Injector Hub indicates an AC inlet power socket, which accepts input power from 100 to 240V
AC, 50/60Hz. Figure 2-1-4 & 2-1-5 shows rear panel of the PoE Injector Hub.
Figure 2-1-4: HPOE-1200G Rear Panel
Figure 2-1-5: HPOE-2400G Rear Panel
The PoE Injector Hub is a power-required device, it means, PoE Injector Hub will not work till it is
powered. If your networks should active all the time, please consider using UPS (Uninterrupted Power
Supply) for your device. It will prevent you from network data loss or network downtime.
In some area, installing a surge suppression device may also help to protect your device from being
damaged by unregulated surge or current to the PoE Injector Hub or the power adapter.
13

User’s Manual of HPOE-1200G / HPOE2400G
2.2 Installing the PoE Injector Hub
This section describes how to install your PoE Injector Hub and make connections to the PoE Injector Hub. Please read the
following topics and perform the procedures in the order being presented. PLANET PoE Injector Hub do not need software
configuration. To install the PoE Injector Hub on a desktop or shelf, simply complete the following steps.
2.2.1 Desktop Installation
To install a PoE Injector Hub on a desktop or shelf, simply complete the following steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the PoE Injector Hub.
Step2: Place the PoE Injector Hub on a desktop or shelf near an AC power source.
Step3: Keep enough ventilation space between the PoE Injector Hub and the surrounding objects.
When choosing a location, please keep in mind the environmental restrictions discussed in Chapter
1, Section 5, in Specification.
Step4: Connect your PoE Injector Hub to network 802.3at / 802.3af powered devices (PD) and Switch.
A. Connect one end of a standard network cable to the upper stack 10/100/1000 RJ-45 ports on the front of the PoE
Injector Hub.
B. Connect the other end of the cable to the 802.3at / 802.3af powered devices (PD) such as IP phone, wireless
access point, IP camera, splitter, or switch etc.
C. Connect the one end of a standard network cable to the relative lower stack 10/100/1000 RJ-45 port on the front
of the PoE Injector Hub.
D. Connect the other end of the cable to the port of Switch.
Connects to the PoE Injector Hub require UTP Category 5e/6 network cabling with RJ-45 tips. For
more information, please see the Cabling Specification in Appendix A.
Step5: Supply power to the PoE Injector Hub.
A. Connect one end of the power cable to the PoE Injector Hub.
B. Connect the power plug of the power cable to a standard wall outlet.
When the PoE Injector Hub receives power, the Power LED should remain solid Green.
2.2.2 Rack Mounting
To install the PoE Injector Hub in a 19-inch standard rack, follow the instructions described below.
Step1: Place your PoE Injector Hub on a hard flat surface, with the front panel positioned towards your front side.
Step2: Attach a rack-mount bracket to each side of the PoE Injector Hub with supplied screws attached to the package.
Figure 2-2-1 shows how to attach brackets to one side of the PoE Injector Hub.
14

User’s Manual of HPOE-1200G / HPOE2400G
Figure 2-2-1: Brackets attaching to the PoE Injector Hub
You must use the screws supplied with the mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate the warranty.
Step3: Secure the brackets tightly.
Step4: Follow the same steps to attach the second bracket to the opposite side.
Step5: After the brackets are attached to the Injector, use suitable screws to securely attach the brackets to the rack, as
shown in Figure 2-2-2.
Figure 2-2-2: Mounting the PoE Injector Hub in a Rack
Step6: Proceeds with the steps 4 and steps 5 of session 2.2.1 Desktop Installation to connect the network cabling and
supply power to your PoE Injector Hub.
15

User’s Manual of HPOE-1200G / HPOE2400G
2.2.3 Network Application Installation
The PoE Injector Hub is not equipment with data switching function between data ports. To inject PoE power and transmit
data packets to PDs, the PoE Injector Hub is usually link to an Ethernet switch. Typically, the Mid-Span Injector is installed
between regular Ethernet switch and PDs, and mostly it is located close to the Ethernet switch side.
To install a PoE Injector Hub on a network environment, simply complete the following steps:
Step1: Power on the PoE Injector Hub and connect the RJ-45 cable from the “Data” port to the Ethernet switch port.
Step2: Connect the RJ-45 cable from the “Data + Power” ports to the PDs, such as VoIP phone, IP camera.
Step3: Check the link status on both PD and Ethernet switch, once the Injector start to deliver 52V power over RJ-45 cables
to PDs, the PoE In-Use LED of the PoE Injector Hub lights.
Figure 2-2-3: Network application installation
The PoE Injector Hub supports Data passive mode, that is, even the PoE Injector Hub is manual power off, the data
between “DATA” port and “DATA & PWR” port can still be transmitted without data loss.
16

User’s Manual of HPOE-1200G / HPOE2400G
17
2.2.4 Power over Ethernet Powered Device
3
~
5
W
a
Voice over IP phones
Enterprise can install POE VoIP Phone,
A
Ethernet/non-Ethernet end-devices to the
UPS is installed for un-interrupt power sys
t
control system.
Wireless LAN Access Points

User’s Manual of HPOE-1200G / HPOE2400G
3 MANAGEMENT
This chapter describes how to manage the PoE Injector Hub. Topics include:
- Overview
- Management method
- Logging on to the PoE injector Hub
3.1 Overview
The PoE injector Hub provides a user-friendly, Web interface. Using this interface, you can perform various device
configuration and management activities, including:
System
Power over Ethernet
Tools
3.2 Requirements
■ Network cables.
Use standard network (UTP) cables with RJ45 connectors.
■ Subscriber PC installed with Ethernet NIC (Network Card)
■ Workstations of subscribers running Windows 98/ME, NT4.0, 2000/2003/XP, MAC OS X or later, Linux, UNIX or
other platform compatible with TCP/IP protocols.
■ Above PC installed with WEB Browser and JAVA runtime environment Plug-in
It is recommended to use Internet Explore 7.0 or above to access the PoE Injector Hub.
18

User’s Manual of HPOE-1200G / HPOE2400G
3.3 Management Method
User can manage the PoE injector Hub by Web Management via a network connection.
3.3.1 Web Management
The PoE Injector Hub can be configured through an Ethernet connection, the factory default IP address is 192.168.0.100
with subnet mask 255.255.255.0, so please make sure the manager PC must be set on the same IP subnet address. For
example, if POE Injector Hub IP address is keeps factory default then your manager PC should be set 192.168.0.x (where
x is a number between 1 and 254, except 100) with subnet mask 255.255.255.0.
1. Use Internet Explorer 7.0 or above Web browser. Enter IP address http://192.168.0.100 to access the Web interface.
Figure 3-1-1: Web Management over Ethernet
2. When the following login screen appears, please enter the default username "admin" and password “admin” to login
the main screen of PoE Injector Hub. The login screen in Figure 3-1-2 appears.
Default IP Address: 192.168.0.100
Default Account: admin
Default Password: admin
Figure 3-1-2: PoE Injector Hub Web Login screen
19

User’s Manual of HPOE-1200G / HPOE2400G
1. For security reason, please change and memorize the new password after this first setup.
2. Only accept command in lowercase letter under Web interface.
3.3.2 PLANET Smart Discovery Utility
For easily list the PoE Injector Hub in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual
CD-ROM is an ideal solution.
The following install instructions guiding you for run the Planet Smart Discovery Utility.
Deposit the Planet Smart Discovery Utility in administrator PC.
Run this utility and the following screen appears.
Figure 3-1-3: Planet Smart Discovery Utility Screen
If there are two LAN cards or above in the same administrator PC, choose different LAN card by use the
“Select Adapter” tool.
20