Planet IPOE-171-60W User manual

Industrial 802.3bt Multi-Gigabit PoE++ Injector
IPOE-171-60W/IPOE-171-95W
User’s Manual

Table of Contents
1. Package Contents...................................................................... 3
2. ProductSpecications ................................................................ 4
3. Product Outlook ........................................................................ 7
3.1 Product Outlook.................................................................. 7
3.2 Industrial PoE++ Injector Upper Panel.................................10
3.3 Wiring the Power Inputs.....................................................10
3.4 Wiring the Fault Alarm Contact ...........................................12
4. Mounting Installation ................................................................13
4.1 DIN-rail Mounting Installation .............................................13
4.2 Wall-mount Plate Mounting .................................................13
4.3 Side Wall-mount Plate Mounting..........................................14
4.4 Grounding the Device.........................................................14
5. Hardware Installation................................................................15
5.1 Before Installation..............................................................15
5.2 IPOE-171-60W/IPOE-171-95W Installation ...........................15
6. Customer Support ....................................................................17

3
1. Package Contents
Thank you for purchasing PLANET IPOE-171 Single-port 802.3bt PoE++
Injector series. In the following section, the term “IPOE-171 Series”
means the IPOE-171-60W or IPOE-171-95W.
Model LAN Port Speed PoE Standard PoE Budget
IPOE-171-60W 10M/100M/
1G/2.5G/5Gbps IEEE 802.3at/bt 60 watts
IPOE-171-95W 10M/100M/
1G/2.5G/5Gbps IEEE 802.3at/bt 95 watts
Please unpack the box of the device carefully, and the box should
contain the following items:
802.3bt PoE injector x 1
User’s manual x 1
Dust cap x 2
Wall-mount kit x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.

4
2.ProductSpecications
Product IPOE-171-60W IPOE-171-95W
HardwareSpecications
Interface
Input Port 1 x RJ45 STP
Data In
Output Port 1 x RJ45 STP
PoE (Data + Power) Out
Input Power
Terminal
Block
1
Network Cable*
Twisted-pair cable up to 100 meters (328ft)
10BASE-T: 4-pair UTP Cat. 3, 4, 5, 5e, 6, 6A
100BASE-TX: 4-pair UTP Cat. 5, 5e, 6, 6A
1G/2.5G: 4-pair UTP Cat. 5e, 6, 6A
5G: 4-pair UTP Cat. 6, 6A
LED Indicators
System: Power 1 (Green),
Power 2 (Green),
Alarm (Red)
PoE Port: PoE-in-Use x 1 (Amber)
PoE Usage: PoE Usage x 3 (Amber)
Data Rate 10M/100M/1G/2.5G/5Gbps
Dimensions
(W x D x H) 135 x 87.8 x 32 mm
ESD Protection 6KV DC
Enclosure Metal case
Weight 406g 443g
Power Requirements DC 48~54V, 2A max. DC 12~54V, 6A max.
Unit Output Voltage DC 45~53V DC 54V
Power Consumption 75 watts max. 120 watts max.
No. of devices that can
be powered 1

5
Installation DIN-rail kit or wall-mount ear
Alarm
Provides one relay output for power failure
Alarm Relay current carry ability: 1A @ DC
24V
Enclosure IP30 slim type metal case
Power over Ethernet
PoE Standard IEEE 802.3bt Type 3
PSE
IEEE 802.3bt Type 4
PSE
PoE Power Output
Budget
DC 50~53V
/ 60-watt
PoE via 4-pair
DC 45~53V / 30-watt
PoE via 2-pair
DC 54V / 95-watt PoE
via 4-pair
DC 54V / 30-watt PoE
via 2-pair
PoE Power Output
Max. 60W@1m cable
Max. 51W@100m
cable
-DC 24V~48V input:
Max. 89.5W@1m
cable
Max. 75W@100m
cable
-DC 12V input:
Max. 60W@1m cable
Max. 52W@100m
cable
PoE Power Supply Type End-span + Mid-span
Power Pin Assignment Pair 1 End-span: 1/2 (-), 3/6 (+)
Pair 2 Mid-span: 4/5 (+), 7/8 (-)
PoE Mode Standard mode
Legacy and Force mode
Standards Conformance
Standards Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3bz 2.5G/5GBASE-T
IEEE 802.3bt 4-pair Power over Ethernet
IEEE 802.3at Power over Ethernet Plus

6
Regulatory Compliance FCC Part 15 Class A, CE
Environment
Operating Temperature -40 ~ 75 degrees C
Storage Temperature -40 ~ 85 degrees C
Operating Humidity 5 ~ 90%, relative humidity, non-condensing
Storage Humidity 5 ~ 90%, relative humidity, non-condensing
Caution
1. As IEEE 802.3bt device provides high power, please use
high-quality network cable and RJ45 connector.
2. The maximum PoE output power depends on the cable
length, the quality of cable, and DC input voltage.

7
3. Product Outlook
3.1 Product Outlook
20W 40W 60W+
PoE Power Usage
PoE
in-Use
Standard Legacy
10/100/1G/2.5G/5G
Ethernet
10/100/1G/2.5G/5G
Ethernet+DC
P1 P2 Alarm
IPOE-171-60W
802.3bt PoE++
30W 60W 90W+
PoE Power Usage
PoE
in-Use
Standard Legacy
10/100/1G/2.5G/5G
Ethernet
10/100/1G/2.5G/5G
Ethernet+DC
P1 P2 Alarm
IPOE-171-95W
802.3bt PoE++
Figure 1: IPOE-171-60W outlook Figure 2: IPOE-171-95W outlook
IPOE-171-60W LED Indicators:
LED Color Function
P1 Green Lights to indicate power 1 has power.
P2 Green Lights to indicate power 2 has power.
Alarm Red Lights to indicate either power 1 or power 2 has no
power.

8
PoE-in-
Use Amber Lights to indicate the device is providing PoE power.
PoE
Usage Amber
Monitor DC input voltage:
When user powers on IPOE-171-60W, the injector will
detect the DC input voltage and then PoE Usage LED
willashthreetimes.
20W: Flashing three times means the DC input
voltage is 48~50.9V.
40W: Flashing three times means the DC input
voltage is 51~52.9V.
Monitor power usage:
20W:
1.OtoindicatethePoEusageislessthan9W.
2. Blinks to indicate that the PoE usage is around
10W to 19W.
3. Lights to indicate the PoE usage is more than 20W.
40W:
1. Blinks to indicate that the PoE usage is around
30W to 39W.
2. Lights to indicate the PoE usage is more than 40W.
60W+:
1. Blinks to indicate that the PoE usage is around
50W to 59W.
2. Lights to indicate the PoE usage is at the
maximum.
IPOE-171-95W LED Indicators:
LED Color Function
P1 Green Lights to indicate power 1 has power.
P2 Green Lights to indicate power 2 has power.
Alarm Red Lights to indicate either power 1 or power 2 has no
power.
PoE-in-
Use Amber Lights to indicate the device is providing PoE power.

9
PoE
Usage Amber
30W:
1.OtoindicatethePoEusageislessthan14W.
2. Blinks to indicate that the PoE usage is around
15W to 29W.
3. Lights to indicate the PoE usage is more than 30W.
60W:
1. Blinks to indicate that the PoE usage is around
45W to 59W.
2. Lights to indicate the PoE usage is more than 60W.
90W+:
1. Blinks to indicate that the PoE usage is around
75W to 89W.
2. Lights to indicate the PoE usage is at the
maximum.
PoE Mode of IPOE-171 series:
PoE Mode Description
Standard
(Default)
The standard mode is chosen to provide power to the PD
devices that follow the IEEE 802.3at/bt standard.
Legacy
The legacy mode supports Ultra PoE. It is chosen to
provide power to the PD devices that do not fully follow the
IEEE 802.3at/bt standard.
Force
Warning
If the output power of injector is less than 1 watt when in
the Legacy mode, after 20 seconds, the Force mode will be
enabled. When the Force mode is enabled, it will provide
PD with a maximum of 60 watts. If the output power of
injector is less than 1 watt when in the Force mode, after 2
seconds, the Legacy mode will be enabled.
Note
After changing the PoE mode, please power off and then
on the PoE injector to make the change effective.

10
3.2 Industrial PoE++ Injector Upper Panel
The upper panel of the IPOE-171 series has one terminal block
connector where there are two DC power inputs.
DC Input:
48-54V , 2A max.
Max. Fault Alarm Loading: 24V, 1A
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 3: IPOE-171-60W upper panel.
DC Input:
12-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 4: IPOE-171-95W upper panel.
3.3 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of the IPOE-
171 series is used for two DC redundant power inputs. Please follow
the steps below to insert the power wire.
Step 1: Insert Positive/Negative DC power wires into Contacts 1 and 2
for POWER 1, or 5 and 6 for POWER 2.
DC Input:
12-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 5: Power input pins.

11
Step 2: Tighten the wire-clamp screws for preventing the wires from
loosening.
123456
Power 1 Alarm Power 2
+ - + -
Figure 6: PWR1 & PWR2 Pins of Terminal Block.
Note
1. The wire gauge for the terminal block should be in the
range between 12 ~ 24 AWG.
2. As the DC input connector of the IPOE-171 series is
polarity protected, connecting Positive/Negative DC
power wires to the wrong pins will not damage the unit.

12
3.4 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block
connector as the picture shows below. After inserting the wires,
the IPOE-171 series will detect the fault status of the power failure
and then form an open circuit. The following illustration shows an
application example for wiring the fault alarm contacts.
Figure 7: Fault Pin of Terminal Block.
Note
1. The wire gauge for the terminal block should be in the
range between 12 ~ 24 AWG.
2. Alarm relay circuit accepts up to 24V, max. 1A currents.
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Fault
Figure 8: Fault Alarm Contact

13
4. Mounting Installation
This section describes how to install the industrial device and make
connections to it. Please read the following sections and perform the
procedures in the order being presented.
Note
In the installation steps below, this manual uses PLANET
Industrial Switch as an example. The steps for PLANET
Industrial Slim-type Switch, Industrial Media/Serial
Converter and Industrial PoE devices are similar.
4.1 DIN-rail Mounting Installation
1
2
4.2 Wall-mount Plate Mounting

14
4.3 Side Wall-mount Plate Mounting
* The above pictures are for illustration only.
4.4 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a
sudden lightning could cause fatal damage to the device.
DC Input:
12-54V , 6A max.
Max. Fault Alarm Loading: 24V, 1A
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Earth Ground

15
5. Hardware Installation
The following section describes the hardware features of the IPOE-171
series. Before connecting any network device to it, please read this
chapter carefully.
5.1 Before Installation
Before your installation, it is recommended to check your network
environment. If there is any IEEE 802.3bt device that needs to be
powered on and works normally, the IPOE-171 series is the solution
that supplies power to this Ethernet device conveniently and easily. If
there is diculty in nding a power socket for the AC-DC connection
to your non-IEEE 802.3at/bt networked device, the IPOE-171 series
with POE-173S/IPOE-173S can supply DC power to this Ethernet device
conveniently and easily.
Note
1. In the installation steps below, this manual uses
the IPOE-171-60W as an example. Except the input
voltage, the steps for the IPOE-171-95W are similar.
2. Note that the input power range of the IPOE-171-60W
is 48 ~ 54V DC and the input power range of IPOE-
171-95W is 12 ~ 54V DC.
5.2 IPOE-171-60W/IPOE-171-95W Installation
1. Connect the power ranging from 12V/48V DC to 54V DC to the
6-pin terminal block of the IPOE-171-60W/IPOE-171-95W. The
power LED will be steadily on.
2. Connect a standard Ethernet cable from an Ethernet switch or
PC workstation to “Ethernet” port of the IPOE-171-60W/IPOE-
171-95W.
3. Connect the long cable to the “Ethernet+DC” port.

16
4. The IPOE-171-60W/IPOE-171-95W can directly connect with any
IEEE 802.3at/bt end-nodes, such as PTZ (pan, tilt & zoom) IP
cameras, PTZ speed dome cameras, color touch screens, Voice over
IP (VoIP) telephones and multi-channel wireless LAN access points
which support IEEE 802.3at/bt In-line Power over Ethernet port.
IPOE-171 Series
Industrial
Switch
Power
Supply
Data
100 meters
DC
Power Line (DC)
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
Power Data PoE PTZ
IP Camera
PoE
Power
DC Input
DC
-40
℃
75
℃
Figure 9: Architecture of connected IEEE 802.3at/bt device
Once the IPOE-171-60W detects the existence of an IEEE 802.3at/bt
device, the PoE-in-Use LED indicator will be steadily on to show it is
providing power.
Note
1. According to IEEE 802.3at/bt Power over Ethernet, the
IPOE-171 Series will not inject power to the cable if
not connected to IEEE 802.3at/bt device. But the Force
mode is exceptional.
2. Depending on the length of cable, the PoE power which
PD receives is different.

17
6. Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource at the PLANET Web site rst to check if it could solve
your issue. If you need more support information, please contact
PLANET support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Support team mail address:
[email protected]
Copyright ©PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.

18
FCC Statement
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
ISEDC Statement
CAN ICES-003(A) / NMB-003(A)
This device complies with Industry Canada license-exempt RSS
standard(s).
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Le present appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioelectrique subi, meme si le brouillage est susceptible
d'en compromettre le fonctionnement.
CE Mark Warning
This device is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.

19
WEEE Warning
To avoid the potential eects on the environment and human
health as a result of the presence of hazardous substances in
electrical and electronic equipment, end users of electrical
and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.