Planet FGSW-2402VS User manual

User's Manual
FGSW-2402VS
FGSW-2620VSF
FGSW-2624SF
24-Port 10/100Mbps
with 2-Gigabit
Web Smart Ethernet Switch
- 1 -

- 2 -
Trademarks
Copyright ©PLANET Technology Corp. 2006.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your com-
ments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful in-
terference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose
of WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 24-Port 10/100Mbps with 2-Gigabit Web Smart Ethernet Switch User's Manual
FOR MODELS: FGSW-2402VS/FGSW-2620VSF
REVISION: 2.1(JANUARY.2007)
Part No.: 2080-A81030-001

- 3 -
TABLE OF CONTENTS
1. INTRODUCTION..........................................................................................................................................5
1.1 CHECKLIST ..............................................................................................................................................................5
1.2 ABOUT THE SWITCH..................................................................................................................................................5
1.3 FEATURES ...............................................................................................................................................................6
1.4 SPECIFICATION.........................................................................................................................................................6
2. HARDWARE DESCRIPTION......................................................................................................................8
2.1 FRONT PANEL ..........................................................................................................................................................8
2.2 REAR PANEL............................................................................................................................................................9
2.3 HARDWARE INSTALLATION .......................................................................................................................................10
2.3.1 Desktop Installation ....................................................................................................................................... 10
2.3.2 Rack Mounting............................................................................................................................................... 10
2.3.3 Installing the SFP transceiver ........................................................................................................................ 11
3. SWITCH MANAGEMENT.......................................................................................................................... 13
3.1 OVERVIEW .............................................................................................................................................................13
3.2 MANAGEMENT METHOD ..........................................................................................................................................13
3.2.1 Web Management ......................................................................................................................................... 13
3.3 LOGGING ON TO THE WEB SMART SWITCH ................................................................................................................13
4. WEB MANAGEMENT.................................................................................................................................14
4.1 LOGIN IN TO THE SWITCH.........................................................................................................................................14
4.2 PORT STATUS ........................................................................................................................................................15
4.3 PORT CONFIGURATION............................................................................................................................................16
4.4 TRUNK CONFIGURATION ..........................................................................................................................................18
4.5 VLAN CONFIGURATION ...........................................................................................................................................20
4.5.1 Enable port-based VLAN function and add a port-based VLAN group .......................................................... 20
4.5.2 Edit existence port-based VLAN group.......................................................................................................... 25
4.5.3 Delete existence port-based VLAN group...................................................................................................... 26
4.5.4 Disable port-based VLAN function................................................................................................................. 28
4.5.5 Enable 802.1Q VLAN function and add a new VLAN group .......................................................................... 31
4.5.6 Configure Advanced 802.1Q VLAN Setting ................................................................................................... 34
4.5.7 Edit existence 802.1Q VLAN group ............................................................................................................... 36
4.5.8 Delete existence 802.1Q VLAN group........................................................................................................... 37
4.6 PORT MONITORING.................................................................................................................................................39
4.7 QOSCONFIGURATION.............................................................................................................................................40
4.8 PORT COUNTERS ....................................................................................................................................................43
4.9 ACCESS CONTROL LIST...........................................................................................................................................44
4.10 WEB SMART FUNCTION.........................................................................................................................................52
4.11 MISC OPERATION .................................................................................................................................................57
4.11.1 Switch Configuration.................................................................................................................................... 58
4.11.2 TFTP Firmware Upgrade............................................................................................................................. 61
4.11.3 Password Setting......................................................................................................................................... 62
4.11.4 IP Configuration........................................................................................................................................... 63
4.11.5 Factory Default ............................................................................................................................................ 64
4.11.6 Reboot System ............................................................................................................................................ 66
4.11.7 System Information...................................................................................................................................... 68
4.12 LOGOUT ..............................................................................................................................................................69
5. SWITCH OPERATION................................................................................................................................72
5.1 ADDRESS TABLE ....................................................................................................................................................72
5.2 LEARNING ..............................................................................................................................................................72
5.3 FORWARDING &FILTERING......................................................................................................................................72
5.4 STORE-AND-FORWARD ...........................................................................................................................................72
5.5 AUTO-NEGOTIATION ...............................................................................................................................................72
6.TROUBLESHOOTING.................................................................................................................................73
APPENDIX A - NETWORKING CONNECTION ............................................................................................74
A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS ........................................................................................................................74
A.2 RJ-45 CABLE PIN ASSIGNMENT ................................................................................................................................74
APPENDIX B - ACCESS CONTROL LIST APPLICATION GUIDE.............................................................76
Before the ACL Configure ….................................................................................................................................. 77
Case 1: Deny specific Source IP Address – Host................................................................................................... 78
Case 2: Deny specific Source IP Address – Class C.............................................................................................. 80
Case 3: Deny IP packets to specific Class C network ............................................................................................ 82
Case 4: Deny specific VLAN packets ..................................................................................................................... 84

- 4 -
Case 5: Deny Specify Protocol – HTTP / WWW .................................................................................................... 86
Case 6: Deny Specify Protocol – SMTP ................................................................................................................. 88

- 5 -
1. INTRODUCTION
1.1 Checklist
Check the contents of your package for following parts:
zThe Web Smart Switch x1
zUser's manual CD x1
zQuick installation guide x1
zPower cord x 1
zRubber feet x 4
zRack mount accessory x 1
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton
including the original packing material, and use them against to repack the product in case there is a need to return it
to us for repair.
In the following section, the term “Web Smart Switch” means the Switch devices, ie. FGSW-2402VS,
FGSW-2620VSF and FGSW-2624SF; term of “switch” can be any third switches.
1.2 About the Switch
The FGSW-2402VS offers 24 10/100Mbps Fast Ethernet ports with 2 open slots (port25, 26). The two open slots can be
installed by optionally two of 1000Base-T port, 100Base-FX, or 1000Base- SX/LX fiber-optic interfaces. The distance can
be extended from 100 meters (TP), 2 kilometers (Multi-mode, ST or SC), up to 15 kilometers (Single-mode, SC).
The FGSW-2620VSF provides 24 10/100Mbps Fast Ethernet ports and 2 Gigabit TP/SFP combo ports.
The FGSW-2624SF provides 24 100Base-FX Fast Ethernet ports and 2 Gigabit TP/SFP combo ports.
The two Gigabit ports of FGSW-2620VSF and FGSW-2624SFeither can be 1000Base-T for 10/100/1000Mbps or
1000Base-SX/LX through SFP (Small Factor Pluggable) interface. The distance can be extended from 100 meters (TP),
550 meters (Multi-mode fiber), up to above 10/50/70/120 kilometers (Single-mode fiber).
Both Web Smart Switches are equipped with non-blocking 8.8Gbps backplane greatly simplifies the tasks of upgrading
your LAN to cater for increased bandwidth demands.
For efficient management, the Web Smart Switch is equipped with web interface. The two Web Smart Switches can be
programmed for basic switch management functions such as port speed configuration, Port Trunking, IEEE 802.1Q
Tag-Based VLAN and Port-based VLAN, Port Mirroring, QoS, bandwidth control, Access Control list and Misc Con-
figuration.
The Web Smart Switch provides port-based VLAN (including overlapping). The VLAN groups allowed on the 2 Web
Smart Switches will be maximally up to 26 for port-based VLAN. Via supporting port trunking, the Web Smart Switch
allows the operation of a high-speed trunk combining multiple ports. The Web Smart Switch provides seven groups of up
to 8-ports for trunking, and it supports fail-over as well.
With its Auto-Negotiation capability, all the RJ-45/STP ports of Web Smart Switch can be configured to speeds of
10/20Mbps or 100/200Mbps automatically. In addition, the product is equipped with the MDI/MDI-X auto detection for
easily plug and play connection, regardless of cabling types-straight through or crossover.

- 6 -
1.3 Features
◆ Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3z and IEEE 802.3ab Gigabit Ethernet standard
◆ 24-Port 10/100 Mbps Fast Ethernet Switch
◆ 2 open slots for 1000Base-T and 100Base-FX, 1000Base-SX/LX fiber-optic interface with various connection
media and distances (FGSW-2420VS)
◆ 2-Port Gigabit TP/SFP combo ports( FGSW-2620VSF)
◆ Each Switching ports support auto-negotiation-10/20, 100/200Mbps supported
◆ Auto-MDI/MDI-X detection on each RJ-45 port
◆ Prevents packet loss with back pressure (half-duplex) and 802.3x PAUSE frame flow control (full- duplex)
◆ High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erro-
neous packets to optimize the network bandwidth
◆ 8K MAC address table, automatic source address learning and ageing
◆ 512K Bytes packet buffers
◆ Web interface for Switch basic management and setup
◆ Support IEEE 802.1Q Tagged VLAN
◆ Support up to 26 port-based VLAN groups
◆ Support up to 7 Trunk groups, each trunk for up to maximum 8 port with 800Mbps bandwidth
◆ Port mirroring allows monitoring of the traffic across any port in real time
◆ Support QoS and bandwidth control on each port
◆ Supports Access Control List function
◆ 19-inch rack mount size
◆ Internal full-range power supply suitable for worldwide use
◆ EMI standards comply with FCC, CE class A
1.4 Specification
Product FGSW-2402VS FGSW-2620VSF FGSW-2624SF
Hardware Specification
10/100Mbps Ports 24 10/ 100Base-TX RJ-45 Auto-MDI/MDI-X ports --
100Base-FX Ports -- 24 100Base-FX
Module Slots
2 open slots for 1000Base-T
and 100Base-FX,
1000Base-SX/LX fiber -optic
interface
2 Gigabit TP/SFP combo ports
Switch Processing Scheme Store-and-forward
Throughput (packet per second) 6.547Mpps
Switch fabric 8.8Gbps
Address Table 8K entries
Share data Buffer 512K Bytes
Flow Control Back pressure for half duplex, IEEE 802.3x Pause Frame for full duplex
Dimensions 440 x 120 x 44 mm, 1U height 440 x 220 x 44

- 7 -
Weight 1.87kg 1.85kg 2.6kg
Power Requirement 100~240V AC, 50-60 Hz
Power Consumption /
Dissipation 13.5 Watts maximum / 46 BTU/hr maximum
5 watts (without SFP)
23.1 watts maximum / 73
BTU
Temperature Operating: 0~50 degree C, Storage -40~70 degree C
Humidity Operating: 10% to 90%, Storage: 5% to 95% (Non-condensing)
Smart function
System Configuration Web interface
Port Status
Display
per port’s disable/enable status,
per port’s link status and speed duplex mode.
Flow control status
Port Configuration
Per port disable/enable,
Auto-negotiation disable/enable.
10/100Mbps full and half duplex mode selection.
Flow control disable/enable and bandwidth control on each port
Trunk Configuration Support 7 groups of 8-Port trunk support
VLAN Configuration Maximum up to 26 VLAN groups for both Port-based VLAN and 802.1Q VLAN
Port Monitoring One Mirroring port to monitor one mirrored port.
The monitor modes are RX, TX and RX & TX
QoS Configuration IEEE 802.1p QoS on each port
Port counters Display detail traffic counters on each port
Access Control List Supports up to 16 Access Control list group
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3z(Gigabit Ethernet)
IEEE 802.3x (Full-duplex flow control)
IEEE 802.1p Priority QoS
IEEE 802.1Q Tagged VLAN

- 8 -
2. HARDWARE DESCRIPTION
This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same Web Smart Switch
and automatically distinguishes the speed of incoming connection.
This section describes the hardware features of Web Smart Switch. For easier management and control of the Web
Smart Switch, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the
unit LED indicators. Before connecting any network device to the Web Smart Switch, read this chapter carefully.
2.1 Front Panel
The Front Panel of the Web Smart Ethernet Switch consists of 24x Auto-Sensing 10/100Mbps Ethernet RJ-45 Ports, the
FGSW-2402VS provide two open slots can be installed by optionally two of 1000Base-T port, 100Base-FX, or
1000Base- SX/LX fiber-optic interfaces. The FGSW-2620VSF provides 2 Gigabit TP/SFP combo ports either can be
1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through SFP (Small Factor Pluggable) interface. For the Fiber
switch FGSW-2624SF, it provides 24 100Base-FX Fast Ethernet ports and 2 Gigabit TP/SFP combo ports.
The LED Indicators are also located on the front panel of the Web Smart Switch.
Figure 2-1: FGSW-2402VS Switch front panel
Figure 2-2: FGSW-2620VSF Switch front panel
Figure 2-3: FGSW-2624SF Switch front panel
2.1.1 LED indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
Per 10/100Mbps port
LED Color Function
LNK/ACT Green Lights to indicate the link through that port is successfully established.
100 Orange Lights to indicate the port is running in 100Mbps speed.

- 9 -
Per 10/100/1000Base-T port /SFP interfaces (FGSW-2620VSF only)
LED Color Function
LNK/ACT
1000 Green
Lit: indicate that the port is operating at 1000Mbps.
Off: indicate that the port is operating at 10Mbps or 100Mbps.
Blink: indicate that the switch is actively sending or receiving data over that port.
LNK/ACT
100 Green
Lit: indicate that the port is operating at 100Mbps.
Off: indicate that the port is operating at 10Mbps or 1000Mbps.
Blink: indicate that the switch is actively sending or receiving data over that port.
FDX Green
Lit: indicate that the port is operating at full-duplex mode.
Off: indicate that the port is operating at half-duplex mode.
Per 100Base-FX port (FGSW-2624SF only)
LED Color Function
LNK/ACT Green
Lit: indicate that the port is operating at 100Mbps.
Off: indicate that the port is link down
Blink: indicate that the switch is actively sending or receiving data over that port.
#Notice:
1. Press the RESET button once. The Web Smart Switch will reboot automatically.
2. Press the RESET button for 5 seconds. The Web Smart Switch will back to the factory default
mode; the entire configuration will be erased.
3. The FGSW-2402VSv2 must work with MII-V series module for 100Base-FX fiber connection.
4. The 2 Gigabit TP/SFP combo ports are shared with port 25/26 of FGSW-2620VSF/
FGSW-2624SF.Either of them can operate at the same time.
2.2 Rear Panel
The rear panel of the Web Smart Switch indicates an AC inlet power socket, which accepts input power from 100 to
240VAC, 50-60Hz.
Figure 2-4: FGSW-2402VS/FGSW-2620VSF Switch rear panel
ON
OFF
POWER
Figure 2-5: FGSW-2624SF Switch rear panel
Power Notice:
1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the
time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data
loss or network downtime.

- 10 -
2. In some area, installing a surge suppression device may also help to protect your Web Smart Switch from being
damaged by unregulated surge or current to the Web Smart Switch.
his part describes how to install your Web Smart Ethernet Switch and make connections to the Switch. Please read the
dures in the order being presented o install your Web Smart Switch on a desktop
ng steps.
o install Web Smart Switch on a desktop or shelf, simply completed the following steps:
the recessed areas on the bottom of the Web Smart Switch.
cts.
scussed in
2.3 Hardware Installation
T
following topics and perform the proce .T
or shelf, simply completed the followi
2.3.1 Desktop Installation
T
Step 1: Attached the rubber feet to
Step 2: Place the Web Smart Switch on a desktop or shelf near an AC power source.
Step 3: Keep enough ventilation space between the Web Smart Switch and the surrounding obje
#Notice:
When choosing a location, please keep in mind the environmental restrictions di
Chapter 1, Section 4, Specification.
Step 4
. Connect one end of a standard network cable to the 10/100 RJ-45 ports on the front of the Web Smart Switch.
ork devices such as printer servers, workstations or routers…etc.
or
: Connect your Switch to network devices.
A
B. Connect the other end of the cable to the netw
#Notice: more information, please see the Cabling Specification in Appendix A.
Connection to the Web Smart Switch requires UTP Category 5 network cabling with RJ-45 tips. F
Step 5
. Connect one end of the power cable to the Web Smart Switch.
andard wall outlet then power on the Web Smart Switch.
emain solid Green.
o install the Web Smart Switch in a 19-inch standard rack, follow the instructions described below.
rt Switch on a hard flat surface, with the front panel positioned towards your front side.
d to the package.
: Supply power to the Web Smart Switch.
A
B. Connect the power plug of the power cable to a st
When the Web Smart Switch receives power, the Power LED should r
2.3.2 Rack Mounting
T
Step 1: Place your Web Sma
Step 2: Attach a rack-mount bracket to each side of the Web Smart Switch with supplied screws attache
Figure 2-6 shows how to attach brackets to one side of the Web Smart Switch.
Figure 2-6 Attaching the brackets to the Web Smart Switch
Caution:
must use the screws su rts by using incorrect screws
ould invalidate your warranty.
You
w
pplied with the mounting brackets. Damage caused to the pa

- 11 -
Step 3: Secure the brackets tightly.
ached to the Web Smart Switch, use suitable screws to securely attach the brackets to
2-7.
Step 4: Follow the same steps to attach the second bracket to the opposite side.
Step 5: After the brackets are att
the rack, as shown in Figure
Figure 2-7 Mounting the Web Smart Switch in a Rack
Step 6: Proceed with the steps 4 and steps 5 of section 2.3.1 Desktop Installation to connect the network cabling and
supply power to your Web Smart Switch.
he sections describe how to insert an SFP transceiver into an SFP slot.
The SFP transceivers are hot-plug e and hot-swappable. You can plug-in and out the transceiver to/from any SFP port
e Figure 2-8 appears.
2.3.3 Installing the SFP transceiver
T
without having to power down the Switch. As th
Figure 2-8 Plug-in the SFP transceiver
Approved PLANET SFP Transceivers
PLANET Web Smart switches support both single mode and mu he following list of approved
LANET SFP transceivers is correct at the time of publication:
ransceiver )
■
■
lti mode SFP transceiver. T
P
■MGB-SX SFP (1000BASE-SX SFP t
■MGB-LX SFP (1000BASE-LX SFP transceiver )
MFB-FX SFP (100Base-FX SFP transceiver - 2Km)
MFB-F20 SFP (100Base-FX SFP transceiver -20Km)

- 12 -
#Note:supported, the Switch will not recogniz
It recommends using PLANET SFPs on the Switch. If you insert a SFP transceiver that is not
e it.
Before
. Make sure both side of the SFP transfer are with the same media type, for example: 1000Base-SX to 1000Base-SX,
1000Bas-LX to 1000Base-LX.
-mode fiber cable-with one side must be male du-
Conne t
Attach the duplex LC connector on the network cable into the SFP transceiver.
of the cable to a device – switches with SFP installed, fiber NIC on a workstation or a Media
P transceiver is operating
4. P port if the link failed. Co works with some fiber-NICs or Media Converters, set the
connect the other switches, workstation or Media Converter.
1
2. Check the fiber-optic cable type match the SFP transfer model.
¾To connect to 1000Base-SX SFP transfer, use the multi-mode fiber cable- with one side must be male duplex
LC connector type.
¾To connect to 1000Base-LX SFP transfer, use the single
plex LC connector type.
c the fiber cable
1.
2. Connect the other end
Converter..
3. Check the LNK/ACT LED of the SFP slot on the front of the Switch. Ensure that the SF
correctly.
Check the Link mode of the SF
Link mode to “1000 Force” is needed.

- 13 -
3. SWITCH MANAGEMENT
This chapter describes how to manage the Web Smart Switch. Topics include:
- Overview
- Management method
- Logging on to the Web Smart Switch
3.1 Overview
The Web Smart Switch provides a user-friendly, web interface. Using this interface, you can perform various switch
configuration and management activities, including:
Please refer to the following Chapter 4 for the details.
3.2 Management Method
User can manage the Web Smart Switch by Web Management via a network or dial-up connection.
3.2.1 Web Management
You can manage the Web Smart Switch remotely by having a remote host with web browser, such as Microsoft Internet
Explorer or Netscape Navigator.
Using this management method:
The Web Smart Switch must have an Internet Protocol (IP) address accessible for the remote host.
3.3 Logging on to the Web Smart Switch
When you log on to the Web Smart Switch Web interface for the first time, a sign-on string appears and you are prompted
for a Web login username and password.
The factory default login username and password is admin.
#Notice:
1. For security reason, please change and memorize the new password after this first setup.
2. Only accept command in lowercase letter under Web interface.

- 14 -
4. WEB MANAGEMENT
To modify your PC’s IP domain to the same with Web Smart Switch then use the default IP address (192.168.0.100) to
remote configure Web Smart Switch through the Web interface.
#Notice:
The following section will base on the console screens of FGSW-2620VSF, for FGSW-2402VS and
FGSW-2624SF the display will be the same to FGSW-2620VSF.
4.1 Login in to the Switch
To access the Web-browser interface you must first enter the user name and password, the default user name and
password is "admin”. You will see the following screen comes out on the Web browser program:
Figure 4-1 Web login screen
After the User name and Password is entered, you will see the web main menu screen.

- 15 -
Figure 4-2 Web main menu screen
4.2 Port Status
This section provides current status of each port from Web Smart Switch, the screen in Figure 4-3 appears and table
4-1 describes the port status object of Web Smart Switch.
Figure 4-3 Port Status Web Page screen

- 16 -
Table 4-1 Descriptions of the Port Status screen Objects
4.3 Port Configuration
This section introduces detail settings of per port on Web Smart Switch; the screen in Figure 4-4 & 4-5 appears and
table 4-2 descriptions the Port Configuration objects of Web Smart Switch.
Figure 4-4 Port Configuration Web Page screen
Object Description
Port Indicate port 1 to port 26.
Enable Display the port Disable or Enable state of each port on Web Smart Switch.
Link Status The state of the link, indicating a valid link partner device. "Up" means a device is successful con-
nected to the port. “Down” means no device is connected.
Spd/Dpx Display the Speed duplex mode of each port on Web Smart Switch.
Flow Control Display the flow control On or Off state of each port on Web Smart Switch.
Refresh button Press this button for refresh current status of each port on Web Smart Switch.

- 17 -
Figure 4-5 Port Configuration Web Page screen
Table 4-2 Descriptions of the Port Configuration screen Objects
#Remark: InRate/OutRate setting are only for Fast Ethernet Port.
Object Description
Port Indicate port 1 to port 26.
Enable Per port Disable or Enable on Web Smart Switch.
Auto Per port Disable (Off) or enable (On) Auto negotiation on Web Smart Switch.
Spd/Dpx Adjust per port speed duplex mode on Web Smart Switch; the available options are Auto, 100F,
100H, 10F, 10H. Default mode is Auto.
Flow Control Per port Flow control Disable (Off) or enable (On) on Web Smart Switch. Default mode is On.
InRate* Input the value of packet rate sent from the connected port to this port must enable the flow control
feature of this port for the function to work normally. The available value ranges from 1 to 99 and rate
unit: 1Mbps.
OutRate* Input the value of packet rate sent from this port to the connected port. The available value ranges
from 1 to 99 and rate unit: 1Mbps.
Apply button Press this button for save current configuration of each port on Web Smart Switch.

- 18 -
4.4 Trunk configuration
This function allows to configuring the trunk function. It provides up to 7 trunk groups and each trunk group provides 2 to
8 member ports. Please check the member port from “Normal” to 7 trunk groups and the screen in Figure 4-6 & 4-7
appears.
Figure 4-6 Trunk Configuration Web Page screen
Figure 4-7 Trunk Configuration Web Page screen
After setup completed, please press “Apply” button to take effect and the screen in Figure 4-8 appears.

- 19 -
Figure 4-8 Trunk Configuration Web Page screen
Please press “Back” for return to Trunk configuration screen for further configuration. If the member port from each
trunk group is out of range or less than 2 ports than the following screen appears.
Figure 4-9 Trunk Configuration Web Page screen
Please press “Back” for return to Trunk configuration screen for adds other trunk group.

- 20 -
4.5 VLAN configuration
A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic
so only members of the VLAN receive traffic from the same VLAN members. The Web Smart Switch supports two type of
VLAN configuration – 802.1Q Tagged VLAN and Port-Based VLAN. The Port-Based VLAN supports up to 26 VLAN
groups. In the default configuration with VLAN disable, the screen in Figure 4-10 appears.
Figure 4-10 VLAN Setting Web Page screen
4.5.1 Enable port-based VLAN function and add a port-based VLAN group
Select “PortBased” and press “Apply” button, to enable the port-based VLAN function then the Web Smart Switch will
reboot for take affect. The screen in Figure 4-11 appears.
#Notice: Any change of VLAN mode will need system reboot to take effect.