Planet ICA-HM230 User manual

H.264
Internet Camera
&
Internet Video Server
ICA-HM230 / ICA-H312 / ICA-H651 / ICA-HM130 /
ICA-HM135 / ICA-HM350 / ICA-H610 / IVS-H120
Quick Installation Guide
Version 1.2

Table of Contents
Chapter 1. Introduction............................................................................4
1.1 Before Installation ...................................................................... 4
1.2 System Requirements ................................................................4
Chapter 2. Physical Description and Installation .........................................5
2.1 ICA-HM230 H.264 Mega-Pixel CMOS Pan / Tilt Internet Camera.....5
2.1.1 ICA-HM230 Package Content ..............................................5
2.1.2 ICA-HM230 Physical Details ................................................5
2.1.3 ICA-HM230 Installation.......................................................6
2.2 ICA-H312 H.264 25-Meter IR Internet Camera .............................8
2.2.1 ICA-H312 Package Content.................................................8
2.2.2 ICA-H312 Physical Details...................................................8
2.2.3 ICA-H312 Installation....................................................... 10
2.3 ICA-H651 H.264 Outdoor Speed Dome Internet Camera ............. 10
2.3.1 ICA-H651 Package Content............................................... 10
2.3.2 ICA-H651 Physical Details................................................. 11
2.3.3 ICA-H651 Installation....................................................... 12
2.4 ICA-HM130 H.264 Mega-Pixel Dome Internet Camera ................. 14
2.4.1 ICA-HM130 Package Content ............................................ 14
2.4.2 ICA-HM130 Physical Details .............................................. 15
2.4.3 ICA-HM130 Installation..................................................... 17

2.5 ICA-HM135 H.264 Mega-Pixel 20M IR Vandal Proof IP Dome ....... 18
2.5.1 ICA-HM135 Package Content ............................................ 18
2.5.2 ICA-HM135 Physical Details .............................................. 18
2.5.3 ICA-HM135 Installation..................................................... 20
2.6 ICA-HM350 H.264 Mega-Pixel 30M Outdoor IR Internet Camera.....22
2.6.1 ICA-HM350 Package Content ............................................ 22
2.6.2 ICA-HM350 Physical Details .............................................. 22
2.6.3 ICA-HM350 Installation..................................................... 24
2.7 ICA-H610 H.264 Indoor PTZ Internet Camera............................. 25
2.7.1 ICA-H610 Package Content............................................... 25
2.7.2 ICA-H610 Physical Details................................................. 25
2.7.3 ICA-H610 Installation....................................................... 27
2.8 IVS-H120 H.264 Internet Video Server ...................................... 29
2.8.1 Package Content.............................................................. 29
2.8.2 IVS-H120 Physical Details ............................................... 29
2.8.3 IVS-H120 Installation....................................................... 31
Chapter 3. Camera Windows Utility......................................................... 32
Further Information ............................................................................... 35

4
Chapter 1. Introduction
Thank you for purchasing the PLANET H.264 IP Camera. It is versatile
and high image solution of surveillance application for day and night.
The PLANET IP Camera is also a stand-alone camera system with a
built-in processor and web server that provides highest quality video
and system performance.
The PLANET IP Camera support Multi-Prole function can stands for
simultaneously video streams. These Network Cameras can generate
H.264, MPEG-4 and M-JPEG streaming simultaneously to different
clients. Moreover, the resolution can be different from one client to
another. This state-of-art design is considerable to t in various network
environments.
1.1 Before Installation
Before installation, please be sure to read this quick installation guide
and user’s manual (CD) carefully to complete machine installation.
This guide shows how to quick set up the three cameras, unless model
name specied terms “IP Camera” will be used for these three models.
1.2 System Requirements
CPU Intel®Core2 Duo E5300 2.6GHz
RAM 1 GB
Video RAM 128MB
Display Chip nVIDIA GeForce 8500GT
ATI Radeon HD 4350
Display Resolution 1024 x 768 24bits
Operating System Windows 2000 SP4 / Windows XP Pro
SP2 / Windows 2003 / Vista
DirectX 9.0c or above
Required space for installation 100 MB
Recommended HD free space 160 GB
Network Wired Ethernet 100Base-TX

5
Chapter 2. Physical Description and Installation
2.1 ICA-HM230 H.264 Mega-Pixel CMOS Pan / Tilt
Internet Camera
2.1.1 ICA-HM230 Package Content
IP Camera Unit x 1
Power Adapter x 1
Camera Mount Kit x 1
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
Note
If any of the above items are missing, please contact
your dealer immediately.
2.1.2 ICA-HM230 Physical Details
Audio Output
Power Jack
Reset Button
RJ-45

6
1.Audio Output
It allows this device to output audio or alerting sound. Connect with a
3.5Ø phone jack speaker (external adaptor).
2.Power Jack
The input power is DC 12V.
Note
1. Only use the power adapter supplied with internet
camera Otherwise, the product may be damaged.
2. The power adapter is unnecessary when internet
camera is connected to a PoE switch. Otherwise, the
product may be damaged when internet camera is
connected to a PoE switch and power adapter simul-
taneously.
3.RJ-45 LAN Socket
The LAN socket is a RJ-45 connector for connections to 10/100Base-TX
Fast Ethernet cabling. This Ethernet port built N-Way protocol can
detect or negotiate the transmission speed of the network automatically.
Please use CAT-5 cable to connect the IP camera to a 100Mbps Fast
Ethernet network switch or hub.
4.Factory Default Reset
This button is hidden in the pinhole. Please refer to the user’s manual
for more information.
2.1.3 ICA-HM230 Installation
Ceiling Mount
1. Fix the IP camera to L-type bracket with the two supplied screws.

7
2. Fix the bracket and IP camera to the ceiling using two holly wall
anchors and screws.
3. Connect the LAN cable to a switch or hub. When this switch/hub is a
PoE device, you can ignore the next step.
4. Connect DC-Jack to the with the bundle power adapter power source.
5. Done.
Wall Mount
1. Fix the L-type bracket to the wall using two holly wall anchors and
screws.
2. Fix the IP camera to L-type bracket with the two supplied screws.
3. Connect the LAN cable to a switch or hub. When this switch/hub is a
PoE device, you can ignore the next step.
4. Connect DC-Jack to the with the bundle power adapter power source.
5. Done.

8
2.2 ICA-H312 H.264 25-Meter IR Internet Camera
2.2.1 ICA-H312 Package Content
IP Camera Unit x 1
Power Adapter x 1
Camera Mount Kit x 1
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
2.2.2 ICA-H312 Physical Details
1.RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling.
This Ethernet port built N-Way protocol can detect or negotiate the
transmission speed of the network automatically. Please use CAT-5
cable to connect the IP camera to a 100Mbps Fast Ethernet network
switch or hub.
In the LAN socket, there are two LEDs embedded:
LAN LED (green color)
This LED will be ashing while network accessing via Ethernet.
Power LED (orange color)
This LED is used to indicate whether DC power is on or not. In addition,
this LED will be ashing while the network accessing of the IP camera.
RS485 &
DI/DO
MIC in
Line out
Power Jack
RJ-45
Reset Button
Video out

9
2.RS-485: Connect to a local keyboard controller.
DI/DO: Connect to sensor in and alarm out devices.
Cable for I/O connectors:
Name Cable Color Function
DC 12V Brown/White DC 12V (50mA maximum)
GND Blue/White GND
D+ Purple/White RS485 data +
D- Gray RS485 data -
DI Green/White Digital signal input
DO Orange/White Digital signal output
3.Video out (BNC Connector)
The Network Camera also provides composite video output. User can
use BNC video cable to connect the Network Camera with a TV monitor
or VCR.
4.Reset Button
This button is used to restore the all factory default settings.
Sometimes restarting the device will make the system back to a normal
state. However, if the system still got problems after restart, user can
restore the factory default settings and install it again.
Restore the device:
a. Press the button down continuously.
b. Hold the button at least 5 seconds and release it. Then the device
has been restored to default settings and reboot again.

10
5.Power Jack
The input power is DC 12V.
Note
1. Only use the power adapter supplied with internet
camera Otherwise, the product may be damaged.
2. The power adapter is unnecessary when internet
camera is connected to a PoE switch. Otherwise, the
product may be damaged when internet camera is
connected to a PoE switch and power adapter simul-
taneously.
6.MIC in (audio in)
Connect a microphone to the IP camera.
7.Line out (audio out)
Connect a loud speaker to the IP camera. This is for voice alerting and
two-way audio.
2.2.3 ICA-H312 Installation
1. Fix IP camera to desired location with stand.
2. Plug-in Ethernet Cable into RJ-45 connector (LAN port).
3. Connect the attached power adapter to IP camera and plug-in this
adapter into power outlet.
4. Connect Video BNC connector to a TV set if necessary (to check
camera viewing angle and focus).
5. Done.
2.3 ICA-H651 H.264 Outdoor Speed Dome Internet Camera
2.3.1 ICA-H651 Package Content
IP Camera Unit x 1
Power Adapter x 1
Power Box Wall Mount Kit x 1
Power Box Electric Wire Kit x 1

11
Camera Bracket Screws Kit x 1
Waterproof Strip x 1
Terminal Block x 2
Video and Audio Cable x 3
Zoom Cable x 1
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
Note
If any of the above items are missing, please contact
your dealer immediately
2.3.2 ICA-H651 Physical Details
1.RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connects to 10Base-T Ethernet or 100Base-TX Fast Ethernet
cabling. This Ethernet port built N-Way protocol can detect or negotiate
the transmission speed of the network automatically. Please use CAT-5
cable to connect the IP camera to a 100Mbps Fast Ethernet network
switch or hub. The LAN cable is wired well for user’s easy installation.
MIC in Line out 12VDC DI/DO RS485 Video Out AC 24V in

12
2.RS-485: Connect to a local keyboard controller.
DI/DO: Connect to sensor in and alarm out devices.
Name Function
DC 12V DC 12V (60mA maximum)
GND GND
D+ RS485 data +
D- RS485 data -
DI Digital signal input (Digital In)
DO Digital signal output (Alarm Out)
3.Local Video output
The IP camera also provides composite video output. User can use BNC
video cable to connect the IP camera with a TV monitor or VCR.
4.AC 24V in
The input power is AC 24V.
5.MIC in (audio in)
Connect a microphone input source to the IP camera.
6.Line out (audio out)
Connect a loud speaker to the IP camera. This function is for voice
alerting and two-way audio.
2.3.3 ICA-H651 Installation
Wall Mount
1. Disassemble the Outdoor Flange and dome housing with wrench.
Mount the dome housing as gure.
2. Mount the power box on a solid wall. Mount the wall bracket on the
power box.
3. Fix the wall bracket to the outdoor ange with screws and wrench.
Tighten the screws as gure.
4. Connect all the cables as required.

13
5. Mount the Safety Hanging-Lock of the outdoor ange on the outdoor
speed dome. Aim the guide pin of mounting base at the longest
curved chute of outdoor ange. Fix the speed dome on the outdoor
ange. Tighten the screw as gure.
Note
Due to the IP camera is heavy, while installing, be ware
of object falling that could injure workers below or
damage the IP camera permanently.
Ceiling Mount
1. Disassemble the Outdoor Flange and dome housing with wrench.
Mount the dome housing as following.
2. Fix the ceiling bracket and connect it with outdoor ange with screws
and wrench. Tighten the screws as following.
3. Connect all the cables as required.

14
4. Mount the Safety Hanging- Lock of the outdoor ange on the outdoor
speed dome. Aim the guide pin of mounting base at the longest
curved chute of outdoor ange. Fix the speed dome on the outdoor
ange. Tighten the screw as following.
2.4 ICA-HM130 H.264 Mega-Pixel Dome Internet Camera
2.4.1 ICA-HM130 Package Content
IP Camera Unit x 1
Power Adapter x 1
Mount Screws x 4
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
Note
If any of the above items are missing, please contact
your dealer immediately.

15
2.4.2 ICA-HM130 Physical Details
1.RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling.
This Ethernet port built N-Way protocol can detect or negotiate the
transmission speed of the network automatically. Please use CAT-5
cable to connect the IP camera to a 100Mbps Fast Ethernet network
switch or hub.
In the LAN socket, there are two LEDs embedded:
LAN LED (green color)
This LED will be ashing while network accessing via Ethernet.
Power LED (orange color)
This LED is used to indicate whether DC power is on or not. In addition,
this LED will be ashing while the network accessing of the IP camera.
RS485 &
DI/DO
MIC in
Line out
Power Jack
RJ-45
Reset Button

16
2.RS-485: Connect to a local keyboard controller.
DI/DO: Connect to sensor in and alarm out devices.
Cable for I/O connectors:
Name Cable Color Function
DC 12V Brown/White DC 12V (50mA maximum)
GND Blue/White GND
D+ Purple/White RS485 data +
D- Gray RS485 data -
DI Green/White Digital signal input
DO Orange/White Digital signal output
3.Reset Button
This button is used to restore the all factory default settings.
Sometimes restarting the device will make the system back to a normal
state. However, if the system still got problems after restart, user can
restore the factory default settings and install it again.
Restore the device:
a. Press the button down continuously.
b. Hold the button at least 5 seconds and release it. Then the device
has been restored to default settings and reboot again.
4.Power Jack
The input power is DC 12V.
Note
1. Only use the power adapter supplied with internet
camera Otherwise, the product may be damaged.
2. The power adapter is unnecessary when internet
camera is connected to a PoE switch. Otherwise, the
product may be damaged when internet camera is
connected to a PoE switch and power adapter simul-
taneously.

17
5.MIC in (audio in)
Connect a microphone to the IP camera.
6.Line out (audio out)
Connect a loud speaker to the IP camera. This is for voice alerting and
two-way audio.
2.4.3 ICA-HM130 Installation
1. Please select the most suitable position on the wall or ceiling to
install the IP camera.
2. Rotate the dome housing counterclockwise to remove it from the
mounting base.
3. Set the mounting base onto the wall or ceiling and center it over
the mounting hole, using the two retaining screws for the main body,
supplied by the appurtenance bag.
4. For lens adjustment, move the IP camera body (some model type’s
limits the PCB board to 180° rotational adjustment) and set the focus
by turning the lens to the left or right direction. When the IP camera
focus adjustment has been completed, rotate the dome housing
clockwise to secure it to the mounting base.

18
5. Connect the LAN cable to a switch or hub. When this switch/hub is a
PoE device, you can ignore the next step.
6. Connect Power Jack to the bundled power adapter.
7. Done.
2.5 ICA-HM135 H.264 Mega-Pixel 20M IR Vandal Proof IP
Dome
2.5.1 ICA-HM135 Package Content
IP Camera Unit x 1
Power Adapter x 1
Mount Screws x 4
User’s Manual CD-ROM x 1
Quick Installation Guide x 1
Note
If any of the above items are missing, please contact
your dealer immediately.
2.5.2 ICA-HM135 Physical Details
1.RJ-45 LAN socket: Connect to PC or Hub/Switch.
For connect to 10Base-T Ethernet or 100Base-TX Fast Ethernet cabling.
This Ethernet port built N-Way protocol can detect or negotiate the
transmission speed of the network automatically. Please use CAT-5
cable to connect the IP camera to a 100Mbps Fast Ethernet network
switch or hub.
In the LAN socket, there are two LEDs embedded:
LAN LED (green color)
This LED will be ashing while network accessing via Ethernet.

19
Power LED (orange color)
This LED is used to indicate whether DC power is on or not. In addition,
this LED will be ashing while the network accessing of the IP camera.
RS485 &
DI/DO
MIC in
Line out
Power Jack
RJ-45
Reset Button
2.RS-485: Connect to a local keyboard controller.
DI/DO: Connect to sensor in and alarm out devices.
Cable for I/O connectors:
Name Cable Color Function
DC 12V Brown/White DC 12V (50mA maximum)
GND Blue/White GND
D+ Purple/White RS485 data +
D- Gray RS485 data -
DI Green/White Digital signal input
DO Orange/White Digital signal output
3.Reset Button
This button is used to restore the all factory default settings.
Sometimes restarting the device will make the system back to a normal
state. However, if the system still got problems after restart, user can
restore the factory default settings and install it again.

20
Restore the device:
a. Press the button down continuously.
b. Hold the button at least 5 seconds and release it. Then the device
has been restored to default settings and reboot again.
4.Power Jack
The input power is DC 12V.
Note
1. ONLY use package power adapter supplied with the
internet. Otherwise, the product may be damaged.
2. The power adapter is unnecessary when internet
camera is connected to a PoE switch. Otherwise, the
product may be damaged when internet camera is
connected to a PoE switch and power adapter simul-
taneously.
5.MIC in (audio in)
Connect a microphone to the IP camera.
6.Line out (audio out)
Connect a loud speaker to the IP camera. This is for voice alerting and
two-way audio.
2.5.3 ICA-HM135 Installation
1. Use provided L-wrench loosen the tamper-resistant housing cover
(with screws still attached on the cover). The unit has a factory
installed side conduit entry and one may adjust the cables to back
conduit entry according to installation requirement.