Planet POE-151S User manual

IEEE 802.3at / af Power over Ethernet Splitters
Fendeur Ethernet IEEE 802.3at / af
802.3at / af PoE Strom über Ethernet Splitter
Il Power over Ethernet Splitter 802.3at / af
O 802.3at / af Energia para Divisores Ethernet
Сплиттер 802.3at / af PoE
El 802.3at / af Energía sobreEthernet Separador
POE-151S / POE-152S / POE-162S
User's Manual

Table of Contents
English
1. Overview ......................................................................... 1-1
2. Package Contents ............................................................. 1-1
3. Product Outlook................................................................ 1-2
4. LED Indication.................................................................. 1-2
5. Hardware Installation ........................................................ 1-3
6. Product Specication ......................................................... 1-7
Française
1. Vue d’ensemble ................................................................ 2-1
2. Contenu du lot ................................................................. 2-1
3. Détail du produit .............................................................. 2-2
4. Voyant DEL ...................................................................... 2-2
5. Installation du matériel ..................................................... 2-3
6. Caractéristiques du produit ................................................ 2-7
Deutsch
1. Überblick ......................................................................... 3-1
2. Packungsinhalt ................................................................. 3-1
3. Produkt Ansicht ................................................................ 3-2
4. LED Anzeige..................................................................... 3-2
5. Hardware Installation ........................................................ 3-3
6. Produkt Spezikation......................................................... 3-7

Italiano
1. Informazioni generali ........................................................ 4-1
2. Contenuto della confezione ................................................ 4-1
3. Vista del Prodotto ............................................................. 4-2
4. LED di stato ..................................................................... 4-2
5. Hardware Installation ........................................................ 4-3
6. Speciche del Prodotto...................................................... 4-7
Português
1. Apresentação ................................................................... 5-1
2. Conteúdos da Embalagem ................................................. 5-1
3. Apresentação do Produto................................................... 5-2
4. Indicação LED .................................................................. 5-2
5. Instalação do Equipamento................................................ 5-3
6. Especicação do Produto ................................................... 5-7
Pусский
1. Обзор ............................................................................. 6-1
2. В комплект входят........................................................... 6-1
3. Внешний вид продукта .................................................... 6-2
4. Светодиодная индикация ................................................. 6-3
5. Установка оборудования.................................................. 6-3
6. Характеристики продукта................................................. 6-8

Español
1. Información general.......................................................... 7-1
2. Contenido del paquete ...................................................... 7-1
3. Vista general del Producto ................................................. 7-2
4. Indicación LED ................................................................ 7-2
5. Instalación del hardware ................................................... 7-3
6. Especicación de Producto ................................................. 7-7

1-1
English
1.Overview
Thank you for purchasing PLANET IEEE 802.3at / af Power over
Ethernet Splitters. These PoE splitters will work with any Power
Sourcing Equipment (PSE) that also supports the IEEE 802.3af / at
standards. The models bellows are included:
Model PoE Standard DC Power Out Power Input Pass-thru. Speed
POE-151S IEEE 802.3af 5V / 12V 48V DC 10/100Mbps
POE-152S IEEE 802.3af 5V / 12V 48V DC 10/100/1000Mbps
POE-162S IEEE 802.3at / af 12V / 24V 56V DC 10/100/1000Mbps
Unless specied, terms of “PoE Splitter” in the following sections
means the model listed above.
2.Package Contents
Upon open the box of the PoE Injector and carefully unpack it. The box
should contain the following items:
POE-151S / POE-152S POE-162S
The 802.3af Power over
Ethernet Splitter x 1
User’s Manual x 1
15cm UTP Straight Network
Cable x 1
DC Plug Cable x 2
The IEEE 802.3at Gigabit High
Power over Ethernet Splitter x 1
User’s Manual x 1
15cm UTP Straight Network
Cable x 1
DC Plug Cable x 2
Note
If any of these pieces are missing or damaged, please
contact your dealer immediately. If possible, retain the
carton including the original packing material, and use
them again to repack the product in case of a need to
return for repair.

1-2
English
3.Product Outlook
POE-151S / POE-152S
There are two RJ-45 Twisted-Pair jack , one LED indicator, one DC 5V /
2A, 12V / 1A DIP switch and one DC Plug connector.
PoE
Ethernet+DC
Power over Ethernet Splitter
IEEE 802.3af
PoE-IEEE 802.3af
Ready Power in-use
DC OUT
Ethernet 5V 12V
Figure 1: POE-151S / POE-152S
POE-162S
There are two RJ-45 Twisted-Pair jack, one LED indicator, one DC 12V /
2A, 24V / 1A DIP switch and one DC Plug connector.
Note
IEEE 802.3at High Power PoE Splitter
DC Out Ethernet
PoE In
PoE In
24V 12V
Incorrect voltage might cause device damage
CAUTION
Disconnect "PoE In" cable before change 12/24V
Figure 2: POE-162S Overview
4.LED Indication
LED Color Function
PoE In Green Lights to indicate the port is connected with IEEE 802.3af
/ at PSE device.

1-3
English
5.Hardware Installation
This section describes the hardware features of PoE Splitter. Before
connecting any network device to the PoE Splitter, refer to this
chapter carefully.
5.1 Before Installation
The PLANET PoE Splitter separates the power out and provides two
kind of DC power output through its DIP switch and its voltage and
current shown as below:
Model DIP switch for DC Voltage Output Default Mode
POE-151S 5V DC / 2A
12V DC / 1A 5V DC
POE-152S
POE-162S 12V DC / 2A
24V DC / 1A 12V DC
POE-151S / POE-152S POE-162S
PoE
Ethernet+DC
Power over Ethernet Splitter
IEEE 802.3af
PoE-IEEE 802.3af
Ready
Power in-use
DC OUT
Ethernet 5V 12V
Note
IEEE 802.3at High Power PoE Splitter
DC Out Ethernet
PoE In
PoE In
24V 12V
Incorrect voltage might
cause device damage
CAUTION
Disconnect "PoE In" cable
before change 12/24V
Note
The PLANET PoE Splitter and PLANET PoE Injector (ex.
POE-151, POE-152 and POE-161) can be installed in
pair. Use of third-party PoE Injector device is allowed if
the device complied with IEEE 802.3at or IEEE 802.3af
standard.

1-4
English
5.2 802.3af/at Device Installation
The PLANET PoE Splitter also provide the alternative to make the non
IEEE 802.3af / 802.3at devices the possibility to connect with an IEEE
802.3af / 802.3at PSE power device like Power over Ethernet Injector
or Power over Ethernet Switch, the gure is as below.
802.3af in-line power Switch
Wireless AP
POE-151S
POE-152S
100 meters
Power
Data
Power
Data
PoE DC
100Base-TX UTP
DC Power Line (DC)
PoE 100Base-TX UTP with PoE
PoE
Ethernet+DC
PoE-IEEE 802.3af
Ready
Power in-use
DC OUT
Ethernet 5V 12V
Figure 3: Connection to IEEE 802.3af Device
100 meters
PTZ Speed
Dome
802.3at in-line power Switch
POE-162S
1000Base-T UTP
1000Base-T UTP with PoE
PoE
Power Line (DC)
DC
PoE
Power
Data
DC
Power
Data
PoE In DC Out Ethernet
24V 12V
Figure 4: Connection to IEEE 802.3at Device

1-5
English
Note
With IEEE 802.3af / 802.3at standard; the PLANET PoE
Splitter also can co-work with IEEE 802.3af / 802.3at
End-Span Switch that feeding power over pin 1, 2, and
3, 6.
5.3 PoE Injector and PoE Splitter Installation
For non PoE remote device or Ethernet equipment, the PoE Splitter
and PoE Injector can runs in pair to provide DC Power for those
devices, the table below shows the model of PLANET PoE Injectors:
Model PoE Standard Max. PoE Out Power In Pass-thru. Speed
POE-151 IEEE 802.3af 15.4 Watts 48V DC 10/100Mbps
POE-152 IEEE 802.3af 15.4 Watts 48V DC 10/100/1000Mbps
POE-161 IEEE 802.3at / af 30 Watts 56V DC 10/100/1000Mbps
Steps:
1. [Switch & PoE Injector] Connect a standard network UTP cable
from Switch / workstation to “Ethernet” port of PoE Injector and
the PoE Injector get DC power from attached power adapter.
2. [PoE Injector & PoE Splitter]
Connect the long UTP cable between the port “Ethernet+DC” of
PoE Injector to the port “Ethernet+DC” (or “PoE IN”) of PoE
Splitter.
The PoE LEDs of both Injector and Splitter will light on continu-
ance.
3. [PoE Splitter]
Connect the UTP cable in the package from “Ethernet” of the
PoE splitter to the RJ-45 port of remote device.
Adjust proper DC power output and connect proper DC plug from
“DC OUT” of PoE Splitter to the remote device.

1-6
English
100 meters
DC
100Base-TX UTP
DC Power Line (DC)
AC Power Line (AC)
PoE 100Base-TX UTP with PoE
Data
Power
Data
Wireless AP
PoE
Power
Data
Ethernet Switch
POE-151/152
PoE Injector
POE-151S
PoE Splitter
PoE
Ethernet+DC
PoE-IEEE 802.3af
Ready
Power in-use
DC OUT
Ethernet 5V 12V
Power
DC
AC
Figure 5: Connection Architecture via 802.3af PoE Injector and PoE Splitter
Switch
POE-162S
POE-161
100 meters
PTZ Camera
1000Base-T UTP
1000Base-T UTP with PoE
PoE
Power Line (AC)
AC
Power Line (DC)
DC
PoE
Power
Data
AC
Power
Data
DC
Power
Data
PoE In DC Out Ethernet
24V 12V
56V DC
Ethernet Ethernet+DC
Figure 6: Connection Architecture via 802.3at PoE Injector and PoE Splitter
Note
Please ensure the PoE Splitter output voltage is correct
before applying power to remote device otherwise, it
may damage the remote device.