Planet FSD-624SF User manual

User's Manual
FSD-624SF
4-Port 100Base-FX POF +
2 Gigabit Web Smart Switch
- 1 -

- 2 -
Trademarks
Copyright ©PLANET Technology Corp. 2008.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product maycause radio interference, in which case the
user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 4-Port 100Base-FX POF + 2-Port Gigabit Web Smart Switch User's Manual
FOR MODEL: FSD-624SF
REVISION: 1.0(JULY.2008)
Part No.: 2080-A33190-000

- 3 -
TABLE OF CONTENTS
1. INTRODUCTION..........................................................................................................................................4
1.1 CHECKLIST ................................................................................................................................................4
1.2 ABOUT THE SWITCH ...................................................................................................................................4
1.3 FEATURES .................................................................................................................................................5
1.4 SPECIFICATION ..........................................................................................................................................6
2. HARDWARE DESCRIPTION......................................................................................................................8
2.1 FRONT PANEL............................................................................................................................................8
2.2 REAR PANEL..............................................................................................................................................9
2.3 HARDWARE INSTALLATION..........................................................................................................................9
3. SWITCH MANAGEMENT..........................................................................................................................12
3.1 OVERVIEW...............................................................................................................................................12
3.2 MANAGEMENT METHOD............................................................................................................................12
3.2.1 Web Management...........................................................................................................................12
3.2.2 PLANET Smart Discovery Utility.....................................................................................................13
3.3 LOGGING ON TO THE FSD-624SF.............................................................................................................14
4. WEB MANAGEMENT.................................................................................................................................15
4.1 LOGIN IN TO THE SWITCH..........................................................................................................................15
4.2 SYSTEM...................................................................................................................................................17
4.2.1 System Information.........................................................................................................................18
4.2.2 IP Configuration..............................................................................................................................19
4.2.3 Password Setting............................................................................................................................20
4.2.4 Factory Default................................................................................................................................21
4.2.5 Firmware Update ............................................................................................................................22
4.2.6 Reboot.............................................................................................................................................25
4.3 PORT MANAGEMENT ................................................................................................................................26
4.3.1 Port Configuration...........................................................................................................................27
4.3.2 Port Mirroring..................................................................................................................................29
4.3.3 Bandwidth Control...........................................................................................................................30
4.3.4 Broadcast Storm Control.................................................................................................................31
4.3.5 Port Statistics..................................................................................................................................32
4.4 VLAN SETTING........................................................................................................................................33
4.4.1 802.1Q VLAN..................................................................................................................................36
4.4.2 Port Based VLAN............................................................................................................................38
4.4.3 MTU VLAN......................................................................................................................................40
4.5 QOSSETTING..........................................................................................................................................41
4.5.1 Priority Mode...................................................................................................................................42
4.5.2 Class of Service Configuration .......................................................................................................43
4.5.3 TCP / UDP Port Based QoS...........................................................................................................45
4.6 SECURITY FILTER.....................................................................................................................................47
4.6.1 MAC Address Filter.........................................................................................................................48
4.6.2 TCP / UDP Filter .............................................................................................................................49
4.7 MISC OPERATION.....................................................................................................................................51
4.8 LOGOUT...................................................................................................................................................52
5. SWITCH OPERATION................................................................................................................................53
5.1 ADDRESS TABLE ......................................................................................................................................53
5.2 LEARNING................................................................................................................................................53
5.3 FORWARDING &FILTERING.......................................................................................................................53
5.4 STORE-AND-FORWARD.............................................................................................................................53
5.5 AUTO-NEGOTIATION.................................................................................................................................53
6. TROUBLESHOOTING................................................................................................................................54
APPENDIX A NETWORKING CONNECTION...............................................................................................55
A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS.........................................................................................................55
A.2 RJ-45 CABLE PIN ASSIGNMENT.................................................................................................................55
A.3 100MBPS,100BASE-FX, SMI TYPE CONNECTOR......................................................................................56

- 4 -
1. INTRODUCTION
1.1 Checklist
Check the contents of your package for following parts:
zFSD-624SF x1
zQuick Installation Guide x1
zUser's manual CD x1
zPower adapter x 1
zRubber feet x 4
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton
including the original packing material, and use them against to repack the product in case there is a need to return it to
us for repair.
In the following section, the term “Web Smart Switch” means the Switch device, ie. FSD-624SF; term of “switch” can
be any third switches.
1.2 About the Switch
The FSD-624SF provides 4 -Port 100Base-FX POF Fast Ethernet ports and two Gigabit Ethernet ports (one 1000Base-T
port and one Gigabit mini-GBIC interface), its fiber-optic interface in the form factor of SMI (Small Multimedia Interface)
interface, the SMI (Small Multimedia Interface) is one kind of POF (Plastic Optic Fiber) interface that can suitable for
low-cost and high-speed data transmission. The two Gigabit ports either can be 1000Base-T for 10/100/1000Mbps or
1000Base-SX/LX through SFP (Small Factor Pluggable) interfaces. The distance can be extended from 100 meters (TP),
550 meters (Multi-mode fiber), up to above 10/20/30/40/50/70/120 kilometers (Single-mode fiber).
The FSD-624SF equipped with non-blocking 4.8Gbps backplane, greatly simplifies the tasks of upgrading your LAN for
catering to increase bandwidth demands. With high performance data transmit and easy installation, the FSD-624SF can
building a fast / reliable network solution of FTTH (Fiber To The Home) and small office network environment from en-
terprise.

- 5 -
For efficient management, the FSD-624SF 4-Port 100Base-FX POF + 2-Port Gigabit Web Smart Switch is equipped with
remote Web interface. The FSD-624SF can be programmed for advanced switch management functions such as port
configuration, port-based / IEEE 802.1Q / MTU VLAN, port mirroring, QoS, bandwidth control, broadcast storm control,
MAC address / TCP & UDP filter and IGMP Snooping v1/v2.
The FSD-624SF provide port-based / IEEE 802.1Q / MTU VLAN (port based / IEEE 802.1Q VLAN including overlapping).
The VLAN groups allowed on the FSD-624SF, will be maximally up to 6 for port-based / 32 for IEEE 802.1Q VLAN groups.
Also the MTU VLAN divides per port as separate LAN group and only can access the public port G1 or public port G1/G2.
The 4-Port 100Base-FX POF fiber interfaces supports 100Mbps full-duplex operation mode (Auto negotiation or force
mode option). The SMI path cord meets the IEEE 1394b specification that can transmit data at S200 (250Mbps) speed for
50 meters, with its Auto-Negotiation capability, the 1000Base-T RJ-45 port of Web Smart Switch can be configured to
speeds of 10/20Mbps / 100/200Mbps (Fast Ethernet) and 1000/2000Mbps (Gigabit Ethernet) automatically. In addition,
the Web Smart Switch is equipped with the MDI/MDI-X auto detection for easily plug and play connection, regardless of
cabling types-straight through or crossover.
1.3 Features
◆ Complies with the IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet standard
◆ 4-Port 100Base-FX POF Web Smart Switch
◆ 2 Gigabit interfaces ( One 1000Base-T port and one Gigabit mini-GBIC interface)
◆ Each Switching ports support auto-negotiation-10/20, 100/200Mbps (Fast Ethernet) , 1000/2000Mbps (Gigabit
Ethernet) supported
◆ Auto-MDI/MDI-X detection on RJ-45 port
◆ Prevents packet loss with back pressure (Half-duplex) and IEEE 802.3x PAUSE frame flow control (Full-duplex)
◆ High performance Store and Forward architecture, broadcast storm control, runt/CRC filtering eliminates erroneous
packets to optimize the network bandwidth
◆ 4K MAC address table, automatic source address learning and ageing
◆ 2.75Mb embedded memory for packet buffers
◆ Remote Web interface for Switch management and setup
◆ Broadcast Storm Control support
◆ Supports up to 6 port-based VLAN groups / 32 IEEE 802.1Q VLAN groups / MTU VLAN
◆ Supports QoS , bandwidth control and MAC address filter / TCP & UDP filter on each port
◆ Supports port mirroring function and IGMP Snooping v1 / v2
◆ Firmware upgrade through Web interface
◆ Password setting, IP setting and device description setting through Planet Smart discovery utility
◆ Desktop placement size
◆ Internal full-range power supply suitable for worldwide use
◆ EMI standards complies with FCC, CE class A

- 6 -
1.4 Specification
Model FSD-624SF
Hardware Specification
100Base-FX POF Ports 4
Gigabit ports One 1000BASE-T port and one Gigabit mini-GBIC SFP interface
Switch Processing Scheme Store-and-Forward
Throughput (packet per second) 3.57Mpps
Switch Fabric 4.8Gbps
Address Table 4K entries
Share Data Buffer 2.75Mb embedded memory for packet buffers
Flow Control Back pressure for half duplex, IEEE 802.3x Pause Frame for full duplex
Dimensions 186 x 143 x 35 mm ( W x D x H))
Weight 370g
Power Requirement DC 5V 2A
Power Consumption / Dissipa-
tion 9.6watts / 32BTU
Temperature Operating: 0~50 degree C
Storage: -40~70 degree
Humidity Operating: 5% to 90%, Storage: 5% to 90% (Non-condensing)
Smart function
System Configuration Web interface
Port configuration Port speed duplex mode selection. Flow control disable / enable. Port disable
/ enable. Port description on each port
Bandwidth Control Yes, 1 / 2 / 4 / 8 / 16 / 32 / 64Mbps
Broadcast Storm Control Yes, 5% / 10% / 25% / 50% / Disable
Port Statistics Display each port’s detail Ethernet traffic counter information
VLAN 6 port-based VLAN groups / 32 IEEE 802.1Q VLAN groups / MTU VLAN
Port Mirroring Port mirroring allows monitoring of the traffic across any port in real time
QoS Allow to assign low / high priority on each port.
First-In-First-Out, All-High-before-Low, Weight-Round-Robin QoS policy.
MAC address / TCP & UDP filter Yes
IGMP Snooping v1 / v2 Allow to disable or enable.

- 7 -
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 (Ethernet)
IEEE 802.3u (Fast Ethernet)
IEEE 802.3ab(Gigabit Ethernet)
IEEE 802.3z(Gigabit Ethernet)
IEEE 802.3x (Full-duplex flow control)
IEEE 802.1Q VLAN
IEEE 802.1p QoS

- 8 -
2. HARDWARE DESCRIPTION
This product provides three different running speeds – 10Mbps, 100Mbps and 1000Mbps in the same Web Smart Switch
and automatically distinguishes the speed of incoming connection.
This section describes the hardware features of Web Smart Switch. For easier management and control of the Web Smart
Switch,familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter displaythe unit LED
indicators. Before connecting any network device to the Web Smart Switch, read this chapter carefully.
2.1 Front Panel
The Front Panel of the Web Smart Ethernet Switch consists of 4x 100Base-FX POF Ports, Also provides 2 Gigabit inter-
faces either can be 1000Base-T for 10/100/1000Mbps and 1000Base-SX/LX through SFP (Small Factor Pluggable)
interface.
The LED Indicators are also located on the front panel of the Web Smart Switch.
PWR 1234G1 G2 4-Port POF
HomeFiber Switch
LNK/ACT
1000/100 POF
Figure 2-1 FSD-624SF Switch front panel
2.1.1 LED indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
Per 100Base-FX POF port
LED Color Function
POF Green Lights to indicate the POF connection is established.
Off to indicate the POF connection is not established.
Blink fast to indicate that the Switch is actively sending or receiving data over that port.
Per 10/100/1000Base-T port interface
LED Color Function
100/1000 Green
Lights to indicate the port is run at 1000Mbps.
Blink Slowly to indicate the port is run at 100Mbps
Off: indicate that the port is operating at 10Mbps.
LNK/ACT Green Lights to indicate the link through that port is established at 10/100/1000Mbps full duplex mode.
Blink slowly to indicate the link through that port is established at 10/100Mbps half duplex mode.
Blink fast to indicate that the Switch is actively sending or receiving data over that port.
Per mini-GBIC SFP interface
LED Color Function
100/1000 Green
Lights to indicate the port is run at 1000Mbps.
Off to indicate the Gigabit fiber connection is not established.
LNK/ACT Green Lights to indicate the Gigabit fiber connection is established.
Blink fast to indicate that the Switch is actively sending or receiving data over that port.

- 9 -
#Notice: 1. Press the RESET button once. The Web Smart Switch will reboot automatically.
2. Press the RESET button for 5 seconds. The Web Smart Switch will back to the factory default
mode; the entire configuration will be erased.
2.2 Rear Panel
The rear panel of the Web Smart Switch indicates a DC power connector, which accepts input power of DC 5V 2A.
Figure 2-2 FSD-624SF Switch rear panel
Power Notice:
1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the
time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data
loss or network downtime.
2. In some area, installing a surge suppression device may also help to protect your Web Smart Switch from being
damaged by unregulated surge or current to the Web Smart Switch.
2.3 Hardware Installation
This part describes how to install your Web Smart Switch and make connections to the Switch. Please read the following
topics and perform the procedures in the order being presented. To install your Web Smart Switch on a desktop or shelf,
simply completed the following steps.
2.3.1 Desktop Installation
To install Web Smart Switch on a desktop or shelf, simply completed the following steps:
Step 1: Attached the rubber feet to the recessed areas on the bottom of the Web Smart Switch.
Step 2: Place the Web Smart Switch on a desktop near an DC power source.
Step 3: Keep enough ventilation space between the Web Smart Switch and the surrounding objects.
#Notice: When choosing a location, please keep in mind the environmental restrictions discussed in
Chapter 1, Section 4, Specification.
Step 4: Connect your Switch to POF devices / network devices
A. Connect one end of a POF cable to the 100Base-FX POF ports on the rear panel of the Web Smart Switch.
B. Connect one end of a standard network cable to 100Base-FX POF ports from other POF devices.
C. Connect one end of a standard network cable to the 1000Base-T RJ-45 port on the rear of the Web Smart Switch.
D. Connect the other end of the cable to the network devices such as printer servers, workstations or routers…etc.
#Notice: Connection to the Web Smart Switch requires Plastic of Fiber / UTP Category 5 network cabling
with RJ-45 tips. For more information, please see the Cabling Specification in Appendix A.
Step 5: Supply power to the Web Smart Switch.
A. Connect one end of the power cable to the Web Smart Switch.
B. Connect the DC 5V power adapter to the Web Smart Switch and power on the Web Smart Switch.
When the Web Smart Switch receives power, the Power LED should remain solid Green.

- 10 -
2.3.2 Installing the SFP transceiver
The sections describe how to insert an SFP transceiver into an SFP slot. The SFP transceivers are hot-pluggable and
hot-swappable. You can plug-in and out the transceiver to/from any SFP port without having to power down the Web Smart
Switch. As the Figure 2-3 appears.
Figure 2-3 Plug-in the SFP transceiver
Approved PLANET SFP Transceivers
PLANET Web Smart Switch supports both single mode and multi mode SFP transceiver. The following list of approved
PLANET SFP transceivers is correct at the time of publication:
■MGB-SX SFP (1000Base-SX SFP transceiver )
■MGB-LX SFP (1000Base-LX SFP transceiver )
#Notice: It recommends using PLANET SFP transceiver on the Web Smart Switch. If you insert a SFP
transceiver that is not supported, the Web Smart Switch will not recognize it.
Before connect the other switches, workstation or Media Converter.
1. Make sure both side of the SFP transceiver are with the same media type, for example: 1000Base-SX to
1000Base-SX, 1000Base-LX to 1000Base-LX.
2. Check the fiber-optic cable type match the SFP transceiver model.
¾To connect to 1000Base-SX SFP transceiver, use the multi-mode fiber cable- with one side must be male
duplex LC connector type.
¾To connect to 1000Base-LX SFP transceiver, use the single-mode fiber cable-with one side must be male
duplex LC connector type.

- 11 -
Connect the fiber cable
1. Attach the duplex LC connector on the network cable into the SFP transceiver.
2. Connect the other end of the cable to a device – switches with SFP installed, fiber NIC on a workstation or a Media
Converter..
3. Check the LNK/ACT LED of the SFP slot on the front of the Web Smart Switch. Ensure that the SFP transceiver is
operating correctly.
4. Check the Link mode of the SFP port if the link failed. Co works with some fiber-NICs or Media Converters, set the Link
mode to “1000 Force” is needed.
Remove the transceiver module
1. Make sure there is no network activityby consult or check with the network administrator. Or through the management
interface of the switch/converter (if available) to disable the port in advance.
2. Remove the Fiber Optic Cable gently.
3. Turn the handle of the MGB module to horizontal.
4. Pull out the module gently through the handle.
Figure 2-4 Pull out the SFP transceiver
#Notice: Never pull out the module without pull the handle or the push bolts on the module. Direct pull
out the module with violent could damage the module and SFP module slot of the Web Smart
Switch.

- 12 -
3. SWITCH MANAGEMENT
This chapter describes how to manage the Web Smart Switch. Topics include:
- Overview
- Management method
- Logging on to the Web Smart Switch
3.1 Overview
The Web Smart Switch provides a user-friendly, Web interface. Using this interface, you can perform various switch con-
figuration and management activities, including:
Please refer to the following Chapter 4 for the details.
3.2 Management Method
User can manage the Web Smart Switch by Web Management via a network connection.
3.2.1 Web Management
The PLANET FSD-624SF provides a built-in browser interface. You can manage the Switch remotely by having a remote
host with Web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox.
The following shows how to startup the Web Management of the Switch, please note the Switch is configured through an
Ethernet connection, make sure the manager PC must be set on the same IP subnet address, for example, the default IP
address of the Switch is 192.168.0.100 (the factory-default IP address), then the manager PC should be set at 192.168.0.x
(where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
Use Internet Explorer 5.0 or above Web browser, enter default IP address http://192.168.0.100
After entering the username and password (default user name and password is “admin”) in login screen

- 13 -
3.2.2 PLANET Smart Discovery Utility
For easily list the FSD-624SF in your Ethernet environment, the Planet Smart Discovery Utility from user’s manual
CD-ROM is an ideal solution.
The following install instructions guiding you for run the Planet Smart Discovery Utility.
1. Deposit the Planet Smart Discovery Utility in administrator PC.
2. Run this utility and the following screen appears.
Figure 3-1 Planet Smart Discovery Utility Screen
#Notice: If there are two LAN cards or above in the same administrator PC, choose different LAN card by
use the “Select Adapter” tool.
3. Press “Refresh” button for list current connected devices in the discovery list, the screen is shown as follow.
Figure 3-2 Planet Smart Discovery Utility Screen

- 14 -
3. This utility show all necessary information from the devices, such as MAC Address, Device Name, firmware version,
Device IP Subnet address, also can assign new password, IP Subnet address and description for the devices.
4. After setup completed, press “Update Device”, “Update Multi” or “Update All” button to take affect. The meaning of
the 3 buttons above are shown as below:
Update Device: use current setting on one single device.
Update Multi: use current setting on choose multi-devices.
Update All: use current setting on whole devices in the list.
The same functions mentioned above also can be finding in “Option” tools bar.
5. To click the “Control Packet Force Broadcast” function, it can allowassign new setting value to the Web Smart Switch
under different IP subnet address.
6. Press “Connect to Device” button then the Web login screen appears in Figure 3-3.
7. Press “Exit” button to shutdown the planet Smart Discovery Utility.
3.3 Logging on to the FSD-624SF
When you log on to the Web Smart Switch Web interface for the first time, a sign-on string appears and you are prompted
for a Web login username and password.
Figure 3-3 Web Smart Switch Web Login Screen
The factory default login username and password is admin.
#Notice: For security reason, please change and memorize the new password after this first setup.

- 15 -
4. WEB MANAGEMENT
To modify your PC’s IP domain to the same with Web Smart Switch then use the default IP address (192.168.0.100) to
remote configure Web Smart Switch through the Web interface.
4.1 Login in to the Switch
To access the Web-browser interface you must first enter the user name and password, the default user name and
password is "admin”. You will see the following screen comes out on the Web browser program:
Figure 4-1 Web Login Screen
After the User name and Password is entered, you will see the Web Main Menu screen.

- 16 -
The Switch Menu provide seven major management functions, the screen in Figure 4-2 appears.
Figure 4-2 Web Main Menu Screen
The seven items and it description shown as below:
◆System: Provide System configuration of Web Smart Switch. Explained in section 4.2.
◆Port Management: Provide Port Management configuration of Web Smart Switch. Explained in section 4.3.
◆VLAN Setting: Provide VLAN Setting configuration of Web Smart Switch. Explained in section 4.4.
◆QoS Setting: Provide QoS Setting configuration of Web Smart Switch. Explained in section 4.5.
◆Security Filter: Provide Security configuration of Web Smart Switch. Explained in section 4.6.
◆Misc Operation: Provide Misc Operation configuration of Web Smart Switch. Explained in section 4.7.
◆Logout: Provide Logout function of Web Smart Switch. Explained in section 4.8.

- 17 -
4.2 System
This section provides System Information, IP Configuration, Password Setting, Factory Default, Firmware Update and
Reboot functions of Web Smart Switch, the screen in Figure 4-3 appears and Table 4-1 describes the System object of
Web Smart Switch.
Figure 4-3 System Web Page Screen
Table 4-1 Descriptions of the System Web Page Screen Objects
Object Description
System Information Display the MAC address, Hardware Version, and Software Version, Device Description. Ex-
plained in section 4.2.1.
IP Configuration Allow to change the IP subnet address of Web Smart Switch. Explained in section 4.2.2.
Password Setting Allow to change the username and password of Web Smart Switch. Explained in section 4.2.3.
Factory Default Allow reset the Web Smart Switch to factory default mode. Explained in section 4.2.4.
Firmware Update Allow proceed firmware upgrade process of Web Smart Switch. Explained in section 4.2.5.
Reboot Allow reboot the Web Smart Switch. Explained in section 4.2.6.

- 18 -
4.2.1 System Information
This section displays the MAC address, Hardware Version and Software Version, also allow define the device description
and press “Apply” button to take affect. The screen in Figure 4-4 appears.
Figure 4-4 System Information Web Page Screen
#Notice: Up to 16 characters is allowed for the Device Description.

- 19 -
4.2.2 IP Configuration
This section provides change the IP Address, Subnet Mask and Gateway, the screen in Figure 4-5 appears.
Figure 4-5 IP Configuration Web Page Screen
.After setup complete and press “Apply” button to take affect. The following screen in Figure 4-6 appears and then another
Web page login screen with newIP address will show up. After input correct username and password then can continue the
Web Smart Switch management.
Figure 4-6 IP Configuration Web Page Screen

- 20 -
4.2.3 Password Setting
This section provides change the Username and Password, the screen in Figure 4-7 appears.
Figure 4-7 Password Setting Web Page Screen
#Notice: Up to 8 characters is allowed for the username and password assign.