Planet GSW-2400HPS User manual

www.PLANET.com.tw
User’s Manual
24-Port Gigabit 802.3at PoE
Web Smart Ethernet Switch
GSW-2400HPS

User’s Manual of GSW-2400HPS
Trademarks
Copyright © PLANET Technology Corp. 2013.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no
warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for
a particular purpose. PLANET has made every effort to ensure that this User's Manual is accurate; PLANET disclaims liability
for any inaccuracies or omissions that may have occurred.
Information in this User's Manual is subject to change without notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User's Manual. PLANET makes
no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to
this User's Manual and/or to the products described in this User's Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and
suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at whose own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be
required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from the power circuit.
Without removing power cable, the device will still consume power from the power source. In view of Saving the Energy and
reducing the unnecessary power consumption. It is strongly suggested to remove the power connection for the device if this
device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste; collect such WEEE separately.
Revision
PLANET 24-Port 10/100/1000Mbps 802.3at PoE Web Smart Ethernet Switch User's Manual
FOR MODEL: GSW-2400HPS
REVISION: 1.0 (April.2013)
Part No: EM-GSW-2400HPS_v1.0 (2081-AK8070-000)
2

User’s Manual of GSW-2400HPS
TABLE OF CONTENTS
1. INTRODUCTION....................................................................................................................6
1.1 Packet Contents ...........................................................................................................................................6
1.2 Product Description.....................................................................................................................................7
1.3 How to Use This Manual..............................................................................................................................9
1.4 Product Features..........................................................................................................................................9
1.5 Product Specifications ..............................................................................................................................11
2. INSTALLATION ...................................................................................................................13
2.1 Hardware Description................................................................................................................................13
2.1.1 Switch Front Panel ..............................................................................................................................................13
2.1.2 LED Indications ...................................................................................................................................................14
2.1.3 Switch Rear Panel...............................................................................................................................................15
2.2 Install the Switch........................................................................................................................................16
2.2.1 Desktop Installation .............................................................................................................................................16
2.2.2 Rack Mounting.....................................................................................................................................................17
3. SWITCH MANAGEMENT....................................................................................................19
3.1 Requirements..............................................................................................................................................19
3.2 Management Access Overview.................................................................................................................20
3.3 Web Management Access .........................................................................................................................20
4. WEB CONFIGURATION......................................................................................................22
4.1 Main Web Page...........................................................................................................................................25
4.2 System.........................................................................................................................................................27
4.2.1 System Information..............................................................................................................................................27
4.2.2 IP Configuration...................................................................................................................................................28
4.2.3 User Configuration...............................................................................................................................................29
4.3 Layer 2 Features.........................................................................................................................................30
4.3.1 Port Configuration................................................................................................................................................30
4.3.2 VLAN...................................................................................................................................................................32
4.3.2.1 VLAN Switching.........................................................................................................................................36
4.3.2.2 VLAN Port Configuration ...........................................................................................................................39
3

User’s Manual of GSW-2400HPS
4.3.2.3 VLAN Setting Example:.............................................................................................................................41
4.3.3 QoS .....................................................................................................................................................................46
4.3.3.1 Port-based Priority Setting.........................................................................................................................47
4.3.3.2 Packet Scheduling.....................................................................................................................................48
4.3.4 Trunk....................................................................................................................................................................50
4.3.4.1 Trunk Group ..............................................................................................................................................51
4.3.5 Port Mirroring.......................................................................................................................................................53
4.3.6 Port Isolation........................................................................................................................................................56
4.3.7 Bandwidth Control ...............................................................................................................................................58
4.3.8 Jumbo Frame ......................................................................................................................................................60
4.3.9 Loop Protection ...................................................................................................................................................61
4.3.10 Green Networking..............................................................................................................................................62
4.4 Security .......................................................................................................................................................63
4.4.1 MAC Address.......................................................................................................................................................63
4.4.1.1 MAC Forwarding Table..............................................................................................................................64
4.4.1.2 Static MAC.................................................................................................................................................65
4.4.2 MAC Constrain....................................................................................................................................................66
4.4.3 Storm Control.......................................................................................................................................................68
4.5 Monitoring...................................................................................................................................................70
4.5.1 Port Statistics.......................................................................................................................................................70
4.5.2 Cable Diagnostics................................................................................................................................................71
4.6 Tools ............................................................................................................................................................73
4.6.1 Maintenance........................................................................................................................................................73
4.6.1.1 Configuration Backup................................................................................................................................73
4.6.1.2 Configuration Upload.................................................................................................................................74
4.6.1.3 Web Firmware Upgrade ............................................................................................................................76
4.6.2 Factory Default....................................................................................................................................................78
4.6.3 Save Configuration..............................................................................................................................................79
4.6.4 Reboot.................................................................................................................................................................80
4.7 Logout .........................................................................................................................................................81
5. SWITCH OPERATION......................................................................................................... 82
5.1 Address Table.............................................................................................................................................82
5.2 Learning ......................................................................................................................................................82
5.3 Forwarding & Filtering...............................................................................................................................82
5.4 Store-and-Forward .....................................................................................................................................82
4

User’s Manual of GSW-2400HPS
5.5 Auto-Negotiation ........................................................................................................................................83
6. POWER OVER ETHERNET OVERVIEW............................................................................84
7. TROUBLESHOOTING.........................................................................................................87
APPENDEX A..........................................................................................................................89
A.1 Switch's RJ-45 Pin Assignments 1000Mbps, 1000Base T.....................................................................89
A.2 10/100Mbps, 10/100Base-TX.....................................................................................................................89
5

User’s Manual of GSW-2400HPS
1. INTRODUCTION
Thank you for purchasing PLANET 24-Port 10/100/1000Mbps 802.3at PoE+ Web Smart Ethernet Switch, GSW-2400HPS.
“Web Smart Switch” is also mentioned in this user’s manual to replace the GSW-2400HPS.
1.1 Packet Contents
Open the box of the Web Smart Switch and carefully unpack it. The box should contain the following items:
Check the contents of your package for the following parts:
The 802.3at PoE Web Smart Switch x1
Quick Installation Guide x1
User’s Manual CD x1
Power Cord x1
Rubber Feet x4
19” Rack Mount Accessory Kit x1
If any of these are missing or damaged, please contact your dealer immediately. If possible, retain the carton including the
original packing materials, and use them to repack the product in case there is a need to return it to us for repair.
6

User’s Manual of GSW-2400HPS
1.2 Product Description
High-Performance, Cost-Effective Gigabit Networking Solution
The GSW-2400HPS is a Layer 2 24-Port 10/100/1000Mbps 802.3at PoE Web Smart Ethernet Switch which can handle
extremely large amount of data in a secure topology linking to an Enterprise backbone or high capacity network server with
48Gbps switching fabric. It supports reliable switching technology and advanced networking features which optimize the
installation and power management of network devices such as wireless access points (AP), Voice over IP (VoIP) phones,
and security video cameras.
Centralized Power Management for Gigabit Ethernet PoE Networking
To fulfill the needs of higher power required PoE network applications with Gigabit speed transmission, the GSW-2400HPS
features high performance Gigabit IEEE 802.3af PoE (Up to 15.4 watts) and IEEE 802.3at PoE+ (Up to 30 watts) on all ports.
It perfectly satisfies the PoE IP camera which needs high power consumption such as IR, PTZ, Speed Dome cameras or even
Box type IP cameras with built-in fan and heater.
The PoE capabilities provided also help to reduce deployment costs for network devices as a result of freeing from restrictions
of power outlet locations. Power and data switching are integrated into one unit, delivered over a single cable and managed
centrally. It thus eliminates cost for additional AC wiring and reduces installation time.
7
24 x Gigabit 802.3at PoE PortsPoE & LNK/ACT Status
Power LED
Wireless
AP/Router
IP Camera
Video
Phone
PTZ
Camera
WiMAX
AP/CPE
IP Phone
Thin Client
Power Requirement
Door
Phone
802.3at
30.8W
802.3af
15.4W

User’s Manual of GSW-2400HPS
8
Robust Layer 2 Features
The GSW-2400HPS can be programmed for advanced switch management functions such as IEEE 802.1Q VLAN, QoS,
static trunk group, port mirroring, port isolation, in band / out band bandwidth control, jumbo frame setting, loop protection,
Green Networking, and static MAC, storm control. The GSW-2400HPS provides 802.1Q Tagged VLAN, and the VLAN groups
allowed will be maximally up to 32. Via aggregation of supporting ports, the GSW-2400HPS allows the operation of a
high-speed trunk combining multiple ports. It enables maximum up to 8 groups of 4 ports for trunking and supports fail-over as
well. The advanced features of QoS and network security included enable the GSW-2400HPS to offer effective data traffic
control for Enterprises, Government or campus another common Ethernet environment application.
Friendly Web-based Management
For efficient management, the GSW-2400HPS is equipped with WEB management interfaces. With the built-in Web-based
management interface, the GSW-2400HPS offers an easy-to-use, platform-independent management and configuration
facility. The GSW-2400HPS supports configuration backup / restore function, this feature will help network administrator to
easily deploy multi GSW-2400HPS devices quickly.

User’s Manual of GSW-2400HPS
1.3 How to Use This Manual
This User Manual is structured as follows:
Section 2, INSTALLATION
The section explains the functions of the Switch and how to physically install the Web Smart Switch.
Section 3, SWITCH MANAGEMENT
The section contains the information about the software function of the Web Smart Switch.
Section 4, WEB CONFIGURATION
The section explains how to manage the Web Smart Switch by Web interface.
Section 5,SWITCH OPERATION
The chapter explains how to do the switch operation of the Web Smart Switch.
Section 6,POWER OVER ETHERNET OVERVIEW
The chapter introduces the IEEE 802.3af / 802.3at PoE standard and PoE provision of the Web Smart Switch.
Section 7,TROUBSHOOTING
The chapter explains how to troubleshoot the Web Smart Switch.
Appendix A
The section contains cable information of the Web Smart Switch.
1.4 Product Features
Physical Port
24-Port 10/100/1000Base-T RJ-45 copper with IEEE 802.3at / 802.3af Power over Ethernet Injector function
Reset button for system factory default
Power over Ethernet
■ Complies with IEEE 802.3at High Power over Ethernet PSE
■ Complies with IEEE 802.3af Power over Ethernet PSE
■ Up to 24 ports of IEEE 802.3af / 802.3at devices powered
■ Supports PoE Power up to 30.8 watts for each PoE ports
■ Auto detects powered device (PD)
■ Circuit protection prevents power interference between ports
■ Remote power feeding up to 100m
Switching
■ Hardware based 10/100/1000Mbps Auto-Negotiation and Auto MDI/MDI-X
■ Flow control for Full Duplex operation and back pressure for Half Duplex operation
■ Integrates address look-up engine, supporting 8K absolute MAC addresses
■ 9K Jumbo Frame size support
■ Automatic address learning and address aging
9

User’s Manual of GSW-2400HPS
Layer 2 Features
Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.3x PAUSE frame flow control (Full-Duplex)
High performance of Store-and-Forward architecture and runt/CRC filtering eliminates erroneous packets to optimize
the network bandwidth
Supports VLAN
IEEE 802.1Q Tagged VLAN
Up to 32 VLANs groups, out of 4094 VLAN IDs
Supports Static Trunk
Maximum 8 trunk groups, up to 4 ports per trunk group
Up to 8Gbps bandwidth (Duplex Mode)
Provides Port Mirror (many-to-1)
Port Mirroring to monitor the incoming or outgoing traffic on a particular port
Port Isolation
1522 / 1536 / 1552 / 9216bytes Jumbo packet setting
Loop Prevention / Detection
Green Networking for energy saving
Quality of Service
Ingress / Egress Rate Limit per port bandwidth control
4 priority queues on all switch ports
Traffic classification:
-Port-based priority
Strict priority and Weight Fair Queue / Weighted Round Robin (WRR) policies
Security
Storm Control support
Broadcast / Multicast / Unknown-Unicast / Unknown-Multicast
MAC Security
MAC Forwarding Table
Static MAC
MAC Constrain
Management
IPv4 Web-based Management Interface
Firmware upgrade through Web interface
Configuration backup / restore through Web interface
Reset button for system reset to factory default
10

User’s Manual of GSW-2400HPS
1.5 Product Specifications
Product GSW-2400HPS
Hardware Specifications
24 10/ 100/1000Base-T RJ-45 Auto-MDI/MDI-X ports
Copper Ports
24 802.3af / 802.3at PoE Injector Ports
PoE Injector Port
LED Indicate
System:
Power (Green)
Port 1 to port 24:
PoE In-Use (Orange)
1000 LNK / ACT (Green), 10/100 LNK / ACT (Orange)
Switch Processing Scheme Store-and-Forward
MAC Addrerss Table 8K entries
Switch Fabric 48Gbps / non-blocking
Throughput @ 64Kbytes 35.7Mpps
Share Data Buffer 3.5Mbit SRAM Packet Buffer
Flow Control IEEE 802.3x Pause Frame for Full-Duplex. Back pressure for Half-Duplex
Jumbo Frame 9216 Bytes
Dimensions (W x D x H) 445 x 207 x 45 mm (1U height)
Weight 2.76kg
Power Consumption Max. 25 Watts / 85 BTU
Power Requirements AC 100~240V, 50/60Hz, 4A max.
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
IEEE 802.3at Enhancement Power over Ethernet / PSE
PoE Power Output Per Port 52V DC, 300mA. Max. 15.4 watts (IEEE 802.3af)
Per Port 52V DC, 600mA. Max. 30 watts (IEEE 802.3at)
PoE Power Budget 300 watts
Number of PD, 7Watts 24
Number of PD, 15.4Watts 19
Number of PD, 30.8Watts 9
Layer 2 Function
IPv4 Web Browser
Management Interfaces
Port Configuration
Port disable / enable
Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
Flow Control disable / enable
Display each port’s state, speed duplex mode, flow control status
Port Statistics Display each port’s state, link status, packet transmit / receive counter
VLAN 802.1Q Tagged Based VLAN
Up to 32 VLAN groups, out of 4094 VLAN IDs
QoS 4 priority queues on all switch ports
11

User’s Manual of GSW-2400HPS
Traffic classification based, Strict priority and Weight Fair Queue / Weighted Round
Robin (WRR) policies
- Port-Based priority
Trunk Static Trunk
Supports 8 groups of 4-Port trunk support
Port mirroring allows monitoring of the traffic across any port in real time
Port Mirroring
Yes
Port Isolation
Bandwidth Control Ingress / Egress Rate Limit per port
Storm Control Broadcast / Multicast / Unknown-Unicast / Unknown-Multicast
Jumbo Frame 1522 / 1536 / 1552 / 9216bytes Jumbo packet setting
Loop Protection Loop Prevention / Detection
Enable / Disable
Green Networking
Security
MAC Security
MAC Forwarding Table
Static MAC
MAC Constrain
Support
Cable Diagnostics
Configuration Backup / Restore Configuration backup / restore through Web interface
Firmware Upgrade Web interface
Standards Conformance
FCC Part 15 Class A, CE
Regulation Compliance
Standards Compliance
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3x Flow Control
IEEE 802.1p QoS
IEEE 802.1Q VLAN Tagging
IEEE 802.3af Power over Ethernet
IEEE 802.3at High Power over Ethernet
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5~ 95% (non-condensing)
Storage Temperature: -10~ 70 degrees C
Relative Humidity: 5~ 95% (non-condensing)
12

User’s Manual of GSW-2400HPS
13
2. INSTALLATION
This section describes the hardware features and installation of the Web Smart Switch on the desktop or rack mount. For easier
management and control of the Web Smart Switch, familiarize yourself with its display indicators, and ports. Front panel
illustrations in this chapter display the unit LED indicators. Before connecting any network device to the Web Smart Switch,
please read this chapter completely.
2.1 Hardware Description
2.1.1 Switch Front Panel
The unit front panel provides a simple interface monitoring the switch. Figure 2-1 shows the front panel of the Web Smart
Switch.
GSW-2400HPS Front Panel
Figure 2-1: GSW-2400HPS Front Panel
■ Gigabit TP Interface (802.3af / 802.3at PoE Injector)
10/100/1000Base-T Copper, RJ-45 Twist-Pair: Up to 100 meters.
■ Reset Button
In the middle of the front panel, the reset button is designed for reset and reboots the Web Smart Switch without turning off
and on the power. The following is the summary table of Reset button function:
Reset Button Pressed and Released Function
> 5 sec: Factory Default
Reset the Web Smart Switch to Factory Default configuration.
The Web Smart Switch will then reboot and load the default
settings as below:
。 Default Username: admin
。 Default Password: admin
。 Default IP address: 192.168.0.100
。 Subnet mask: 255.255.255.0
。 Default Gateway: 192.168.0.254

User’s Manual of GSW-2400HPS
2.1.2 LED Indications
The front panel LEDs indicate instant status of port links, data activity and system power; help monitor and troubleshoot when
needed. Figure 2-2 shows the LED indications of Web Smart Switch.
GSW-2400HPS LED Indication
Figure 2-2: GSW-2400HPS LED Panel
■ System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
■ 10/100/1000Base-T interfaces
LED Color Function
Lights: To indicate the link through that port is successfully established at 1000Mbps.
1000
LNK/ACT Green Blink: To indicate that the switch is actively sending or receiving data over that port.
10/ 100
LNK/ACT Orange Lights:
Blink:
To indicate the link through that port is successfully established at 10Mbps or
100Mbps.
To indicate that the switch is actively sending or receiving data over that port.
Lights: To indicate the port is providing 52VDC in-line power.
PoE In-Use Orange Off: To indicate the connected device is not a PoE Powered Device (PD)
14

User’s Manual of GSW-2400HPS
2.1.3 Switch Rear Panel
The rear panel of the Web Smart Switch indicates an AC inlet power socket, which accepts input power from 100 to 240V AC,
50-60Hz, 4A. Figure 2-3 shows the rear panel of Web Smart Switch.
GSW-2400HPS Rear Panel
Figure 2-3: Rear Panel of GSW-2400HPS
■ AC Power Receptacle
For compatibility with electric service in most areas of the world, the Web Smart Switch’s power supply automatically
adjusts to line power in the range of 100-240V AC and 50/60 Hz, 4A.
Plug the female end of the power cord firmly into the receptalbe on the rear panel of the Web Smart Switch. Plug the other
end of the power cord into an electric service outlet and then the power will be ready.
Power Notice:
The device is a power-required device, meaning it will not work till it is powered. If your networks should
be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will
prevent you from network data loss or network downtime.
In some areas, installing a surge suppression device may also help to protect your Web Smart Switch
from being damaged by irregular surge or current to the Switch or the power adapter.
15

User’s Manual of GSW-2400HPS
2.2 Install the Switch
This section describes how to install your Web Smart Switch and make connections to the Web Smart Switch. Please read the
following topics and perform the procedures in the order being presented. To install your Web Smart Switch on a desktop or
shelf, simply complete the following steps.
2.2.1 Desktop Installation
To install the Web Smart Switch on desktop or shelf, please follows these steps:
Step1: Attach the rubber feet to the recessed areas on the bottom of the Web Smart Switch.
Step2: Place the Web Smart Switch on the desktop or the shelf near an AC power source, as shown in Figure 2-4.
Figure 2-4:Place the Web Smart Switch on the Desktop
Step3: Keep enough ventilation space between the Web Smart Switch and the surrounding objects.
When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1,
Section 4, and Specifications.
Step4: Connect the Web Smart Switch to network devices.
Connect one end of a standard network cable to the 10/100/1000 RJ-45 ports on the front of the Web Smart Switch
Connect the other end of the cable to the network devices such as printer servers, workstations, routers, etc.
Connection to the Web Smart Switch requires UTP Category 5 network cabling with RJ-45 tips. For
more information, please see the Cabling Specification in Appendix A.
16
PoEI n Use
PoEI n Use
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
18 20 22 24
17 19 21 23
2 4 6 8 10 12 14 16
1
PWR
Reset
3 5 7 9 11 13 15
18
17
20
19
22
21
24
23
GSW-2400HPS
1000 ACT
10/100 ACT
LNK
LNK

User’s Manual of GSW-2400HPS
Step5: Supply power to the Web Smart Switch.
Connect one end of the power cable to the Web Smart Switch.
Connect the power plug of the power cable to a standard wall outlet.
When the Web Smart Switch receives power, the Power LED should remain solid Green.
2.2.2 Rack Mounting
To install the Web Smart Switch in a 19-inch standard rack, please follow the instructions described below.
Step1: Place the Web Smart Switch on a hard flat surface, with the front panel positioned towards the front side.
Step2: Attach the rack-mount bracket to each side of the Web Smart Switch with supplied screws attached to the package.
Figure 2-5 shows how to attach brackets to one side of the Web Smart Switch.
Figure 2-5:Attach Brackets to the Web Smart Switch
You must use the screws supplied with the mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate the warranty.
Step3: Secure the brackets tightly.
Step4: Follow the same steps to attach the second bracket to the opposite side.
Step5: After the brackets are attached to the Web Smart Switch, use suitable screws to securely attach the brackets to the rack,
as shown in Figure 2-6.
17
PoE In Use
PoE In Use
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
18 20 22 24
17 19 21 23
2 4 6 8 10 12 14 16
1
PWR
Reset
3 5 7 9 11 13 15
18
17
20
19
22
21
24
23
GSW-2400HPS
1000 ACT
10/100 ACT
LNK
LNK

User’s Manual of GSW-2400HPS
Figure 2-6:Mounting Web Smart Switch in a Rack
Step6: Proceeds with steps 4 and steps 5 of section 2.2.1 for Desktop Installation to connect the network cabling and supply
power to the Web Smart Switch.
18
PoEI n Use
PoEI n Use
2 4 6 8 10 12 14 16
1 3 5 7 9 11 13 15
18 20 22 24
17 19 21 23
2 4 6 8 10 12 14 16
1
PWR
Reset
357911 13 15
18
17
20
19
22
21
24
23
GSW-2400HPS
1000 ACT
10/100 ACT
LNK
LNK

User’s Manual of GSW-2400HPS
3. SWITCH MANAGEMENT
This chapter explains the method that you can use to configure management access to the Web Smart Switch. It describes the
type of management applications and the communication and management protocols that deliver data between your
management device (workstation or personal computer) and the system. It also contains information about port connection
options.
This chapter covers the following topics:
Requirements
Management Access Overview
Web Management Access
3.1 Requirements
Workstation is installed with Ethernet NIC (Network Interface Card)
Workstations of subscribers running Windows XP/2003, Vista, Windows 7, MAC OS X, Linux, Fedora, Ubuntu or other
platforms compatible with TCP/IP protocols.
The above Workstation is installed with Web Browser and JAVA runtime environment Plug-in.
Ethernet Port connection
Network cables - use standard network (UTP) cables with RJ-45 connectors.
It is recommended to use Internet Explore 7.0 or above to access the Web Smart Switch.
19

User’s Manual of GSW-2400HPS
3.2 Management Access Overview
The Web Smart Switch gives you the flexibility to access and manage it using any or all of the following methods:
Web browser interface
The administration Web browser interface support is embedded in the Web Smart Switch software and is available for
immediate use. The web management method has its advantages. Table 3-1 shows the advantage and disadvantage of Web
management method.
Method Advantages Disadvantages
Web Browser Ideal for configuring the switch remotely
Compatible with all popular browsers
Can be accessed from any location
Most visually appealing
Security can be compromised (hackers need
only know the IP address and subnet mask)
May encounter lag times on poor connections
Table 3-1: Web Management Methods Overview
3.3 Web Management Access
The Web Smart Switch offers management features that allow users to manage the Web Smart Switch from anywhere on the
network through a standard browser such as Microsoft Internet Explorer. After you set up your IP address for the switch, you can
access the Web Smart Switch’s Web interface applications directly in your Web browser by entering the IP address of the Web
Smart Switch.
Figure 3-1: Web Management
You can then use your Web browser to list and manage the Web Smart Switch configuration parameters from one central
location, Web Management requires either Microsoft Internet Explorer 7.0 or later, Safari or Mozilla Firefox 1.5 or later.
20