Planet ADSL 2/2+ VoIP Router IAD-200W User manual

ADSL 2/2+ VoIP Router
IAD-200, IAD-200W
User's Manual

Copyright
Copyright (C) 2005 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed
products of PLANET Technology, This User’s Manual contains proprietary
information protected by copyright, and this User’s Manual and all
accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced,
translated, or reduced to any electronic medium or machine-readable form by
any means by electronic or mechanical. Including photocopying, recording, or
information storage and retrieval systems, for any purpose other than the
purchaser's personal use, and without the prior express written permission of
PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representation,
either implied or expressed, with respect to the quality, performance, mer-
chantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does
not represent a commitment on the part of PLANET. PLANET assumes no
responsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in
this User’s Manual, and reserves the right to make improvements to this User’s
Manual and/or to the products described in this User’s Manual, at any time
without notice.
If you find information in this manual that is incorrect, misleading, or incom-
plete, we would appreciate your comments and suggestions.
FCC Compliance Statement
The device confirmed to comply with the requirements of FCC Part 15 Rule.
ii

Operation is subject to the Following two conditions: (1) This device may not
cause harmful interference, and (2) This Device must accept any interference
received, including interference that may cause undesired operation.
Federal Communication Commission (FCC) Radiation
Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncon-
trolled environment. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the antenna shall not be
less than 20 cm (8 inches) during normal operation.
CE mark Warning
This is a class B device. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result
of the presence of hazardous substances in electrical and electronic equipment,
end users of electrical and electronic equipment should understand the meaning
of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC
OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March
1999 on radio equipment and telecommunication terminal Equipment and the
mutual recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Tele-
communications Terminal Equipment and Satellite Earth Station Equipment)
as of April 8, 2000.
iii

Trademarks
The PLANET logo is a trademark of PLANET Technology. This documenta-
tion may refer to numerous hardware and software products by their trade
names. In most, if not all cases, these designations are claimed as trademarks
or registered trademarks by their respective companies.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment.
All guidelines of this and of the computer manufacture must therefore be al-
lowed at all times to ensure the safe use of the equipment.
To avoid struck by lightning, we suggest customers to add a device (lightning
protector / surge protector) front of this ADSL 2/2+ VoIP router. Improper
installation like without this protection and cause the equipment damaged
could void the warranty.
Revision
User’s Manual for PLANET ADSL 2/2+ VoIP Router
Model: IAD-200, IAD-200W
Rev: 1.0 (Aug. 2005)
Part No. EM-IAD200Wv1
iv

Table of Contents
CHAPTER 1 INTRODUCTION.....................................................................1
IAD-200 / IAD-200W Features .................................................................1
Package Contents.......................................................................................4
Physical Details...........................................................................................5
CHAPTER 2 INSTALLATION......................................................................8
Requirements..............................................................................................8
Procedure....................................................................................................8
CHAPTER 3 SETUP......................................................................................10
Overview...................................................................................................10
Configuration Program...........................................................................11
Setup Wizard............................................................................................12
Home Screen.............................................................................................14
LAN Screen...............................................................................................15
Wireless Screen (IAD-200W only)..........................................................17
Wireless Security (IAD-200W only).......................................................20
Trusted Wireless Stations (IAD-200W only).........................................22
Password Screen.......................................................................................24
CHAPTER 4 PC CONFIGURATION..........................................................25
Overview...................................................................................................25
Windows Clients.......................................................................................25
Macintosh Clients.....................................................................................36
Linux Clients ............................................................................................36
Other Unix Systems .................................................................................36
Wireless Station Configuration (IAD-200W only)................................37
Wireless Configuration on Windows XP (IAD-200W only).................37
CHAPTER 5 ADVANCED FEATURES......................................................47
Overview...................................................................................................47
Internet......................................................................................................47
Dynamic DNS (Domain Name Server)...................................................52
Firewall Rules...........................................................................................54
User-defined Services...............................................................................59
Options......................................................................................................61
Schedule ....................................................................................................62
Virtual Servers .........................................................................................64
VoIP...........................................................................................................67
CHAPTER 6 ADVANCED ADMINISTRATION.......................................72
Overview...................................................................................................72
PC Database..............................................................................................73
Config File.................................................................................................77
Logs ...........................................................................................................78
E-mail........................................................................................................80
Diagnostics................................................................................................82
Remote Administration ...........................................................................83
i

Routing......................................................................................................85
Upgrade Firmware...................................................................................89
CHAPTER 7 OPERATION AND STATUS ................................................90
Operation..................................................................................................90
Status Screen ............................................................................................90
Connection Status - PPPoE & PPPoA....................................................94
Connection Details - Dynamic IP Address.............................................95
Connection Details - Fixed IP Address ..................................................97
Using VoIP................................................................................................98
APPENDIX A TROUBLESHOOTING........................................................99
Overview...................................................................................................99
General Problems.....................................................................................99
Internet Access .........................................................................................99
Wireless Access (IAD-200W only)........................................................100
APPENDIX B ABOUT WIRELESS LANS (IAD-200W ONLY) ............102
Modes ......................................................................................................102
BSS/ESS ..................................................................................................102
Channels..................................................................................................103
WEP.........................................................................................................103
WPA-PSK ...............................................................................................103
Wireless LAN Configuration ................................................................104
ii

1
Chapter 1
Introduction
This Chapter provides an overview of the ADSL 2/2+ VoIP router (IAD-200)
/ 802.11g ADSL 2/2+ VoIP router's (IAD-200W) features and capabilities.
Congratulations on the purchase of your new ADSL 2/2+ VoIP router – IAD-200 / 802.11g
ADSL 2/2+ VoIP router – IAD-200W. The IAD-200 / IAD-200W is a multi-function device
providing the following services:
• ADSL 2/2+ Modem.
• Shared Broadband Internet Access (NAT Router) for all LAN & WLAN users.
• Wireless Access Point for 802.11b and 802.11g Wireless Stations. (IAD-200W only)
• VoIP Gateway supporting the industry-standard SIP protocol.
• Ethernet Port for 10BaseT or 100BaseT connection to your LAN.
Figure 1: 802.11g ADSL 2/2+ VoIP router
IAD-200 / IAD-200W Features
The IAD-200 / IAD-200W incorporates many advanced features, carefully designed to provide
sophisticated functions while being easy to use.
Internet Access Features
• Shared Internet Access. All users on the LAN or WLAN can access the Internet
through the IAD-200 / IAD-200W, using only a single external IP Address. The local (in-
valid) IP Addresses are hidden from external sources. This process is called NAT
(Network Address Translation).
• Built-in ADSL Modem. The IAD-200 / IAD-200W has a built-in ADSL modem,
supporting all common ADSL connections.
• IPoA, PPPoE, PPPoA, Direct Connection Support. The IAD-200 / IAD-200W
supports all common connection methods.
1

• Auto-detection of Internet Connection Method. In must situations, the IAD-200 /
IAD-200W can test your ADSL and Internet connection to determine the connection
method used by your ISP.
• Fixed or Dynamic IP Address. On the Internet (WAN port) connection, the IAD-200 /
IAD-200W supports both Dynamic IP Address (IP Address is allocated on connection)
and Fixed IP Address.
Advanced Internet Functions
• Application Level Gateways (ALGs). Applications which use non-standard connec-
tions or port numbers are normally blocked by the Firewall. The ability to define and
allow such applications is provided, to enable such applications to be used normally.
• Special Applications. This feature, also called Port Triggering, allows you to use
Internet applications which normally do not function when used behind a firewall.
• Virtual Servers. This feature allows Internet users to access Internet servers on your
LAN. The required setup is quick and easy.
• Dynamic DNS Support. DDNS, when used with the Virtual Servers feature, allows
users to connect to Servers on your LAN using a Domain Name, even if you have a dy-
namic IP address which changes every time you connect.
• URL Filter. Use the URL Filter to block access to undesirable Web sites by LAN users.
• Firewall. As well as the built-in firewall to protect your LAN, you can define Firewall
Rules to determine which incoming and outgoing traffic should be permitted.
• Scheduling. Both the URL Filter and Firewall rules can be scheduled to operate only at
certain times. This provides great flexibility in controlling Internet -bound traffic.
• Logs. Define what data is recorded in the Logs, and optionally send log data to a Syslog
Server. Log data can also be E-mailed to you.
• VPN Pass through Support. PCs with VPN (Virtual Private Networking) software
using PPTP, L2TP, and IPSec are transparently supported - no configuration is required.
VoIP Features
• SIP Standard Compatible. The IAD-200 / IAD-200W complies with the SIP standard
for VoIP.
• Advanced Call features. Caller ID, Caller name, Call waiting, three-way conference
call, DTMF relay, Voice active detection, Echo canceller.
• FAX Support. Both the T.38 and G.711 Fax standards are supported, allowing both
sending and receiving faxes via the Wireless VoIP Gateway.
• Life line (PSTN fallback) Support. The PSTN (analogue phone) port is automatically
used when the Internet connection is not operational or there is a power failure.
Wireless Features (IAD-200W only)
• Standards Compliant. The IAD-200W complies with the IEEE802.11g (DSSS) speci-
fications for Wireless LANs.
• Supports both 802.11b and 802.11g Wireless Stations. The 802.11g standard
provides for backward compatibility with the 802.11b standard, so both 802.11b and
802.11g Wireless stations can be used simultaneously.
• Speeds up and exceeding 54Mbps. All speeds up to the 802.11g maximum of 54Mbps
are supported. Also, the IAD-200W support TI's proprietary "g-Plus" solution, which al-
lows even faster speeds between compatible wireless devices.
2

• WEP support. Support for WEP (Wired Equivalent Privacy) is included. Key sizes of
64 Bit and 128 Bit are supported. WEP encrypts any data before transmission, providing
protection against snoopers.
• WPA-PSK support. Like WEP, WPA-PSK encrypts any data before transmission,
providing protection against snoopers. The WPA-PSK is a later standard than WEP, and
provides both easier configuration and greater security than WEP.
• Wireless MAC Access Control. The Wireless Access Control feature can check the
MAC address (hardware address) of Wireless stations to ensure that only trusted Wireless
Stations can access your LAN.
• Simple Configuration. If the default settings are unsuitable, they can be changed
quickly and easily.
LAN Features
• Ethernet Port. The IAD-200 / IAD-200W incorporates a 10/100BaseT port for connec-
tion to your existing LAN.
• DHCP Server Support. Dynamic Host Configuration Protocol provides a dynamic IP
address to PCs and other devices upon request. The IAD-200 / IAD-200W can act as a
DHCP Server for devices on your local LAN and WLAN.
Configuration & Management
• Easy Setup. Use your WEB browser from anywhere on the LAN or WLAN for configu-
ration.
• Configuration File Upload/Download. Save (download) the configuration data from
the IAD-200 / IAD-200W to your PC, and restore (upload) a previously-saved configura-
tion file to the device.
• Remote Management. The IAD-200 / IAD-200W can be managed from any PC on
your LAN or Wireless LAN. And, if the Internet connection exists, it can also (optionally)
be configured via the Internet.
• Network Diagnostics. You can use the IAD-200 / IAD-200W to perform a Ping or
DNS lookup.
Security Features
• Password - protected Configuration. Password protection is provided to prevent
unauthorized users from modifying the configuration data and settings.
• Wireless LAN Security. WPA-PSK, WEP, and Wireless access control by MAC
address are all supported. The MAC-level access control feature can be used to prevent
unknown wireless stations from accessing your LAN.
• NAT Protection. An intrinsic side effect of NAT (Network Address Translation) tech-
nology is that by allowing all LAN users to share a single IP address, the location and
even the existence of each PC is hidden. From the external viewpoint, there is no network,
only a single device - the IAD-200 / IAD-200W.
• Firewall. All incoming data packets are monitored and all incoming server requests are
filtered, thus protecting your network from malicious attacks from external sources.
• Protection against DoS attacks. DoS (Denial of Service) attacks can flood your
Internet connection with invalid packets and connection requests, using so much band-
width and so many resources that Internet access becomes unavailable. The IAD-200 /
IAD-200W incorporates protection against DoS attacks.
3

Package Contents
The following items should be included. If any of these items are damaged or missing, please
contact your dealer immediately.
• The IAD-200 / IAD-200W Unit
• 1 Cat-5 Ethernet (LAN) cable
• 1 RJ-11 (ADSL) cable
• Power Adapter
• Quick Installation Guide
• CD-ROM containing the on-line manual.
4

Physical Details
Front-mounted LEDs
IAD-200
IAD-200W
Figure 2: Front Panel
Power LED
(Green) On - Power on.
Off - No power.
Status LED
(Yellow) Off - Normal operation.
Blinking - This LED blinks during start up, and during a Firmware Up-
grade.
LAN • 100BT - This will be ON if the LAN connection is using 100BaseT,
and Blinking if data is being transferred via the LAN port.
• 10BT - This will be ON if the LAN connection is using 10BaseT, and
Blinking if data is being transferred via the LAN port.
If neither LED is on, there is no active connection on the LAN port.
WLAN LED
(IAD-200W
only)
On - Wireless enabled.
Off - No Wireless connections currently exist.
Flashing - Data is being transmitted or received via the Wireless access
point. This includes "network traffic" as well as user data.
ADSL On - ADSL connection established. (This is a low-level connection, it
does not mean Internet access is available.)
Off - No ADSL connection currently exists.
Flashing - Data is being transmitted or received via the ADSL connection.
PSTN Off - Idle or not connected.
Flashing - PSTN line is in use.
Phone On - Connected to SIP Server.
Off - Idle or not connected.
Flashing (quickly) -Phone is in use.
5

Internet On - Internet connection is available.
Off - No Internet connection available.
Flashing - Data is being transmitted or received.
6

Rear Panel
IAD-200
IAD-200W
Figure 3: Rear Panel
ADSL port Connect this port to your ADSL line.
PSTN Connect this to your PSTN line (normal analog phone line).
Phone Connect a standard phone here.
LAN Connect this port to your hub, using the supplied LAN cable.
Reset Button
(Reset to Defaults) This button will reset the IAD-200 / IAD-200W to the factory default
settings.
To do this, press and hold the Reset Button for five (5) seconds, until
the Status LED is lit, then release the Reset Button, and wait the
IAD-200 / IAD-200W to restart using the factory default values.
Power switch Press IN for power ON, OUT for power OFF.
Power port Connect the supplied power adapter here.
7

Chapter 2
Installation
This Chapter covers the physical installation of the ADSL 2/2+ VoIP router
(IAD-200) / 802.11g ADSL 2/2+ VoIP router (IAD-200W).
Requirements
• TCP/IP protocol must be installed on all PCs.
• To use the Wireless Access Point, all Wireless devices must be compliant with the IEEE
802.11g or IEEE 802.11b specifications.
• For Internet Access, an ADSL service and ISP account.
• For VoIP, a SIP account with a VoIP service provider.
Procedure
Figure 4: Installation Diagram
1. Choose an Installation Site
Select a suitable place on the network to install the IAD-200 / IAD-200W. Ensure the
power is OFF.
For best Wireless reception and performance, the IAD-200W
should be positioned in a central location with minimum obstruc-
tions between the device and the PCs.
Also, if using multiple Access Points, adjacent Access Points should
use different Channels.
2
8

2. Connect LAN Cable
Use the supplied LAN cable to connect the LAN port on the IAD-200 / IAD-200W to
your hub.
3. Connect ADSL Cable
Connect the supplied ADSL cable from the ADSL port on the IAD-200 / IAD-200W to
the ADSL terminator provided by your phone company.
4. Connect PSTN Line
Connect the PSTN socket on the rear of the IAD-200 / IAD-200W to your normal phone
line socket.
5. Connect Phone
Connect a standard phone to the Phone socket on the rear of the IAD-200 / IAD-200W.
6. Power Up
Connect the supplied power adapter to the IAD-200 / IAD-200W. Use only the power
adapter provided. Using a different one may cause hardware damage.
Power up by pressing the rear-mounted power switch IN, and wait for startup to be com-
pleted.
7. Check the LEDs
• The Power LED should be ON.
• The Status LED should flash, then turn Off. If it stays on, there is a hardware error.
• Either the 100BT or 10BT LED should be ON.
• Phone LED should be OFF.
• PSTN LED will be OFF.
• WLAN LED should be ON (IAD-200W only).
• ADSL LED should be ON.
• Internet LED will be OFF.
It will come ON when configuration is complete and correct, and an Internet connec-
tion is established.
For more information, refer to Front-mounted LEDs in Chapter 1.
9

Chapter 3
Setup
This Chapter provides Setup details of the IAD-200 / IAD-200W.
Overview
This chapter describes the setup procedure for:
• Internet Access
• LAN configuration
• Wireless setup
• Assigning a Password to protect the configuration data.
PCs on your local LAN may also require configuration. For details, see Chapter 4 - PC Con-
figuration.
Other configuration may also be required, depending on which features and functions of the
IAD-200 / IAD-200W you wish to use. Use the table below to locate detailed instructions for
the required functions.
To Do this: Refer to:
Configure PCs on your LAN. Chapter 4:
PC Configuration
Use any of the following Advanced features:
• Internet (DMZ, Special Applications, URL Filter)
• Dynamic DNS
• Firewall Rules
• Firewall Services
• Options
• Schedule
• Virtual Servers
• VoIP
Chapter 5:
Advanced Features
Use any of the following Administration features:
• PC Database
• Config File
• Logs
• E-mail
• Diagnostics
• Remote Admin
• Routing
• Upgrade Firmware
Chapter 6
Advanced Administration
Check IAD-200 / IAD-200W operation and Status. Chapter 7:
Operation and Status
3
10

Configuration Program
The IAD-200 / IAD-200W contains an HTTP server. This enables you to connect to it, and
configure it, using your Web Browser. Your Browser must support JavaScript.
The configuration program has been tested on the following browsers:
• Netscape 7.1 or later.
• Mozilla 1.6 or later
• Internet Explorer V5.5 or later
Preparation
Before attempting to configure the IAD-200 / IAD-200W, please ensure that:
• Your PC can establish a physical connection to the IAD-200 / IAD-200W. The PC and the
device must be directly connected (using the Hub ports on the IAD-200 / IAD-200W) or
on the same LAN segment.
• The device must be installed and powered ON.
• If the IAD-200 / IAD-200W's default IP Address (192.168.0.1) is already used by another
device, the other device must be turned OFF until the device is allocated a new IP Address
during configuration.
Using UPnP
If your Windows system supports UPnP, an icon for the IAD-200 / IAD-200W will appear in
the system tray, notifying you that a new network device has been found, and offering to create
a new desktop shortcut to the newly-discovered device.
• Unless you intend to change the IP Address of the IAD-200 / IAD-200W, you can accept
the desktop shortcut.
• Whether you accept the desktop shortcut or not, you can always find UPnP devices in My
Network Places (previously called Network Neighborhood).
Double - click the icon for the IAD-200 / IAD-200W (either on the Desktop, or in My Network
Places) to start the configuration. Refer to the following section Setup Wizard for details of the
initial configuration process.
Using your Web Browser
To establish a connection from your PC to the IAD-200 / IAD-200W:
1. After installing the IAD-200 / IAD-200W in your LAN, start your PC. If your PC is
already running, restart it.
2. Start your WEB browser.
3. In the Address box, enter "HTTP://" and the IP Address of the IAD-200 / IAD-200W, as
in this example, which uses the device's default IP Address:
HTTP://192.168.0.1
4. When prompted to login, use the following username and password.
• User name: admin
• Password: password
11

If you cannot connect
If the IAD-200 / IAD-200W does not respond, check the following:
• The IAD-200 / IAD-200W is properly installed, LAN connection is OK, and it
is powered ON. You can test the connection by using the "Ping" command:
• Open the MS-DOS window or command prompt window.
• Enter the command:
ping 192.168.0.1
If no response is received, either the connection is not working, or your
PC's IP address is not compatible with the IAD-200 / IAD-200W's IP Ad-
dress. (See next item.)
• If your PC is using a fixed IP Address, its IP Address must be within the range
192.168.0.2 to 192.168.0.254 to be compatible with the IAD-200 / IAD-
200W's default IP Address of 192.168.0.1. Also, the Network Mask must be set
to 255.255.255.0. See Chapter 4 - PC Configuration for details on checking
your PC's TCP/IP settings.
• Ensure that your PC and the IAD-200 / IAD-200W are on the same network
segment. (If you don't have a router, this must be the case.)
• Ensure you are using the wired LAN interface. The Wireless interface can only
be used if its configuration matches your PC's wireless settings.
Setup Wizard
The first time you connect to the IAD-200 / IAD-200W, you should run the Setup Wizard to
configure the IAD-200 / IAD-200W for Internet access.
1. Select Setup Wizard on the main menu.
2. Step through the Wizard until finished.
• You need the data supplied by your ISP. Most connection methods require some data
input.
• The common connection types are explained in the following table.
3. On the final screen of the Wizard, run the test and check that an Internet connection can be
established.
4. If the connection test fails:
• Check all connections, and the front panel LEDs.
• Check that you have entered all data correctly.
12

Common Connection Types
Type Details ISP Data required
Dynamic
IP Address Your IP Address is allocated automatically, when you connect
to you ISP.
a) ADSL parameters (VPI and
VCI) may be required, if they
cannot be detected automatically.
b) Some ISP's may require you to
use a particular Hostname or
Domain name, or MAC (physical)
address.
Static (Fixed)
IP Address Your ISP allocates a permanent IP Address to you.
Usually, the connection is "Al-
ways on".
a) ADSL parameters (VPI and
VCI) may be required, if they
cannot be detected automatically.
b) IP Address allocated to you,
and related information, such as
Network Mask, Gateway IP
address, and DNS address.
PPPoE, PPPoA You connect to the ISP only when
required. The IP address is
usually allocated automatically.
a) ADSL parameters (VPI and
VCI) may be required, if they
cannot be detected automatically.
b) User name and password are
always required.
c) If using a Static (Fixed) IP
address, you need the IP address
and related information (Network
Mask, Gateway IP address, and
DNS address)
IPoA
(IP over ATM) Normally, the connection is "Always on". a) ADSL parameters (VPI and VCI) may be required, if they
cannot be detected automatically.
b) IP Address allocated to you,
and related information, such as
Network Mask, Gateway IP
address, and DNS address.
13

Home Screen
After finishing the Setup Wizard, you will see the Home screen. When you connect in future,
you will see this screen when you connect. An example screen is shown below.
Figure 5: Home Screen
Main Menu
The main menu, on the left, contains links to the most-commonly used screen. To see the links
to the other available screens, click "Advanced" or "Administration".
The main menu also contains two (2) buttons:
• Log Out - When finished, you should click this button to logout.
• Restart - Use this if you wish to restart the IAD-200 / IAD-200W. Note that restarting the
Router will break any existing connections to or through the Router.
Navigation & Data Input
• Use the menu bar on the left of the screen, and the "Back" button on your Browser, for
navigation.
• Changing to another screen without clicking "Save" does NOT save any changes you may
have made. You must "Save" before changing screens or your data will be ignored.
On each screen, clicking the "Help" button will display
help for that screen.
14