Planet WGS-804HPT User manual

Industrial Wall-mount Managed Gigabit Ethernet Switch
WGS-804HPT/WGS-4215-8T/WGS-4215-8T2S
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring the Power Inputs.............................................................................. 5
3.1 Terminal Block Connector Pinout ........................................................... 6
4. Installation................................................................................................. 7
4.1 Wall Mount Installation......................................................................... 7
4.2 Magnet Installation .............................................................................. 8
4.3 DIN-rail Mount Installation ................................................................... 8
5. Starting Web Management .........................................................................10
6. SavingCongurationviatheWeb ...............................................................13
7. RecoveringBacktoDefaultConguration.....................................................14
8. Customer Support .....................................................................................15

3
1. Package Contents
Thank you for purchasing PLANET Industrial Wall-mount Managed Gigabit Switch,
WGS-804HPT / WGS-4215-8T / WGS-4215-8T2S.
The table below shows the models with the number of ports:
Model Name 10/100/1000T
Copper Ports
802.3at PoE
Ports
100/1000 SFP Fiber
Optical Interface
WGS-804HPT 8 4 —
WGS-4215-8T 8 — —
WGS-4215-8T2S 8 — 2
In the following section, unless specied, the term “Wall-mount Managed
Switch” mentioned in this quick installation guide refers to the WGS-804HPT /
WGS-4215-8T / WGS-4215-8T2S.
Open the box of the Wall-mount Managed Switch and carefully unpack it. The box
should contain the following items:
zThe Wall-mount Managed Switch x 1
zQuick Installation Guide x 1
z3-pin Terminal Block Connector x 1
zWall-mounted Kit x 1
zDIN-rail Kit x 1
zMagnet Kit x 1
zRJ45 Dust Cap x 8
zSFP Dust Cap x 2 (WGS-4215-8T2S only)
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later,
Linux, UNIX, or other platforms are compatible with TCP/IP protocols.
zWorkstations are installed with Ethernet NIC (Network Interface Card)
zEthernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45 connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Wall-mount Managed Switch. If the Web interface of the Wall-
mount Managed Switch is not accessible, please turn off the anti-
virus software or firewall and then try it again.

5
3. Wiring the Power Inputs
The Wall-mount Managed Switch features a strong dual power input system
(Terminal block and DC jack) incorporated into customer’s automation network to
enhance system reliability and uptime.
Power Input Range
Model
3-pin Terminal Block DC Jack
WGS-804HPT 48~56V DC 48~56V DC
WGS-4215-8T 12~48V DC, 24V AC 12~48V DC, 24V AC
WGS-4215-8T2S 12~48V DC, 24V AC 12~48V DC
10/100/1000BASE-T RJ45 Port
10/100/1000BASE-T RJ45 Port
3-pin Terminal Block
DC Plug-in

6
3.1 Terminal Block Connector Pinout
To install the 3-pin Terminal Block Connector on the Wall-mount Managed Switch,
simply follow the following steps:
Step 1: Insert positive DC power wire into V+, negative DC power wire into V-,
and grounding wire into Ground.
V+
V
-
Ground
Step 2: Tighten the wire-clamp screws for preventing the wires from loosening
and plug into the Wall-mount Managed switch.
Note
1. The wire gauge should be in the range from 12 to 24 AWG.
2. The device must be grounded.

7
4. Installation
4.1 Wall Mount Installation
To install the Wall-mount Managed Switch on the wall, simply follow the following
steps:
Step 1: There are 4 holes with 8mm diameter on the wall; the distance between
the 2 holes is 133mm(WGS-804HPT/WGS-4215-8T), 163mm(WGS-4215-
8T2S) and the line through them must be horizontal.
Step 2: Install a conductor pipe inside the board hole and ush the edge of the
conductor pipe with the wall surface.
Step 3: Screw the bolts into the conductor pipe. The Wall-mount Managed Switch
is between bolts and conductor pipe, as shown below.

8
4.2 Magnet Installation
To install the Wall-mount Managed Switch on a magnetic surface, simply follow the
following diagram:
4.3 DIN-rail Mount Installation
The DIN-rail kit is included in the package. When the wall-mount application for
the Wall-mount Managed Switch needs to be replaced with DIN-rail application,
please refer to the following gures to screw the DIN-rail on the Wall-mount
Managed Switch. To hang up the Wall-mount Managed Switch, follow the steps
below:
Step 1: Screw the DIN-rail on the Wall-mount Managed Switch

9
Step 2: Lightly insert the button of DIN-rail into the track
1Push
2Click
Step 3: Check whether the DIN-rail is tightly on the track

10
5. Starting Web Management
The following shows how to start up the Web Management of the Wall-mount
Managed Switch. Note the Wall-mount Managed Switch is congured through an
Ethernet connection. Please make sure the manager PC must be set to the same
IP subnet address.
For example, the default IP address of the Wall-mount Managed Switch is
192.168.0.100; then the manager PC should be set at 192.168.0.x (where
x is a number between 1 and 254, except 100) and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 5-1: IP Management Diagram