Planet WGSD-10020 User manual

L2+ Gigabit Ethernet Managed Switch
WGSD-10020 Series
WGSW-20160HP
WGSW-24040 Series
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
4. Logon to Console........................................................................................ 6
5. ConguringIPAddress................................................................................ 7
6. Starting Web Management .......................................................................... 9
7. SavingConguration..................................................................................12
8. RecoveringBacktoDefaultConguration.....................................................13
9. Customer Support .....................................................................................14

3
1. Package Contents
Thank you for purchasing PLANET L2+ Gigabit Ethernet Managed Switch, which
comes with multiple RJ45 copper ports being made for a Gigabit Ethernet Switch
with SFP ber optic connectibility and robust layer 2 and layer 4 features. The
descriptionofthismodelisshownbelow:
WGSD-10020 L2+ 8-Port 10/100/1000Base-T + 2-Port 100/1000Base-X SFP
ManagedSwitch
WGSD-10020HP L2+ 8-Port 10/100/1000Base-T PoE Plus + 2-Port 100/1000Base-X
SFPManagedSwitch
WGSW-20160HP L2+ 16-Port 10/100/1000Base-T PoE Plus + 4-Port Gigabit TP/
SFPComboManagedSwitch
WGSW-24040 L2+ 24-Port 10/100/1000Base-T + 4-Port Shared SFP Managed
Switch
WGSW-24040R L2+ 24-Port 10/100/1000Base-T + 4-Port Shared SFP Managed
Switchw/48VDCRedundantPower
WGSW-24040HP L2+ 24-Port 10/100/1000Base-T PoE Plus + 4-Port Shared SFP
ManagedSwitchw/220W
WGSW-24040HP4 L2+ 24-Port 10/100/1000Base-T PoE Plus + 4-Port Shared SFP
ManagedSwitchw/440W
“Managed Switch” is used as an alternative name in this Quick Installation
Guide.
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zTheManagedSwitchx1
zQuickInstallationGuidex1
zRS232DB9FemaleConsoleCablex1
zRubberFeetx4
zTwoRack-mountingBracketswithAttachmentScrewsx1
zPowerCordx1
zSFPDust-proofCapx2(WGSD-10020Series)
zSFPDust-proofCapx4(WGSW-20160HP/WGSW-24040Series)
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerialPortConnection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS-232
converter.
 The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
zSerial cable -- one end is attached to the RS-232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
zEthernetPortConnection
 Networkcables--Usestandardnetwork(UTP)cableswithRJ-45connectors.
 The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.

5
3. Terminal Setup
Tocongurethesystem,connectaserialcabletoaCOM port on a PC or notebook
computerandtoRS-232typeofserialportoftheManagedSwitch.
Managed Switch
Serial Port
Serial Port
115200,8,n,1
PC / Workstation
with
Terminal emulation software
RS-232
Figure 3-1: Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud :115200
zDatabits :8
zParity :None
zStopbits :1
zFlowcontrol :None
Figure 3-2: COM Port Conguration

6
4. Logon to Console
Once the terminal is connected to the device, power on the Managed Switch, and
the terminal will display “running testing procedures”. Then, the following message
asks to log-in user name and password. The factory default user name and
passwordareshownasfollowsandtheloginscreeninFigure4-1appears.
Username:admin
Password:admin
Figure 4-1: Managed Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

7
5.ConguringIPAddress
TheManagedSwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure5-1.
Figure 5-1: IP Information Screen
 Conguring IP Address
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure5-2.
WGSD-10020HP# congure terminal
WGSD-10020HP(cong)# interface vlan 1
WGSD-10020HP(cong-if-vlan)# ip address 192.168.1.100 255.255.255.0

8
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
Figure 5-2: Conguring IP Address Screen
4.Repeatstep1tocheckiftheIPaddressischanged.
 Store current switch conguration
5.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 5-3: Saving Current Conguration Command Screen
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the Managed
SwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.

9
6. Starting Web Management
The following shows how to start up the Web Management of the Managed
Switch. Note the Managed Switch is congured through an Ethernet connection.
Please make sure the manager PC must be set on the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
then the manager PC should be set at 192.168.0.x (where x is a number
between1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
Managed Switch
RJ-45/UTP-Cable
PC / Workstation with IE Browser
IP Address: 192.168.0.x
IP Address: 192.168.0.100
Figure 6-1: IP Management Diagram
Logging in the Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100(thefactorydefaultIPaddressortheonethatyouhave
justchangedinconsole)toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screeninFigure6-2appears.

10
DefaultUsername:admin
DefaultPassword:admin
Figure 6-2: Login Screen
Note
The following web screen is based an the WGSD-10020HP. For
WGSW-20160HP and WGSW-24040 Series, the displays will be the
sameastheWGSD-10020HP.
3.Afterenteringthepassword,themainscreenappearsasFigure6-3shows.
Figure 6-3: Web Main Screen of Managed Switch