Planet FGSD-1022VHP User manual

8/16/24-Port 10/100TX 802.3at PoE
+ 2-Port Gigabit TP/SFP Combo Ethernet Switch
FGSD-1022VHP/FGSW-1822VHP/FGSW-2622VHP
User’s Manual

Trademarks
Copyright ©PLANET Technology Corp. 2016.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does not
represent a commitment on the part of PLANET. PLANET assumes no responsibility
for any inaccuracies that may be contained in this User’s Manual. PLANET makes
no commitment to update or keep current the information in this User’s Manual,
and reserves the right to make improvements to this User’s Manual and/or to the
products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

Energy Saving Note of the Device
This power required device does not support Standby mode operation. For energy
saving, please remove the power cable to disconnect the device from the power
circuit. Without removing power cable, the device will still consume power from the
power source. In view of Saving the Energy and reducing the unnecessary power
consumption, it is strongly suggested to remove the power connection from the
device if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste and have to collect such WEEE
separately.
Revision
PLANET 8/16/24-Port 10/100TX 802.3at PoE+ 2-Port Gigabit TP/SFP Combo Ethernet
Switch User’s Manual
Models: FGSD-1022VHP, FGSW-1822VHP, FGSW-2622VHP
Revision: 1.0 (January, 2016)
Part No.: 2351-AK3230-000

Table of Contents
1. Introduction ............................................................................................... 5
1.1 Package Contents ................................................................................ 5
1.2 Product Description.............................................................................. 6
1.3 Features ............................................................................................. 8
1.4 Specications .....................................................................................10
2. Hardware Description .................................................................................12
2.1 Front Panel ........................................................................................12
2.1.1 LCD Monitor Indicators ..............................................................15
2.1.2 LED Indicators ..........................................................................17
2.2 Rear Panel .........................................................................................18
3. Hardware Installation .................................................................................19
3.1 Desktop Installation ............................................................................20
3.2 Rack Mounting ...................................................................................21
3.3 Installing the SFP Transceiver ..............................................................22
3.4 Product Applications............................................................................25
3.5 Power over Ethernet Powered Devices ..................................................26
4. Power over Ethernet Overview ....................................................................27
5. Troubleshooting .........................................................................................30
Appendix A Networking Connection ..................................................................31
A.1 Switch’s Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T...............31
A.2 10/100Mbps, 10/100BASE-TX ..............................................................31

5
1. Introduction
Thank you for purchasing PLANET 8/16/24-Port 10/100TX 802.3at PoE+ 2-Port
Gigabit TP/SFP Combo Ethernet Switch series, FGSD-1022VHP, FGSW-1822VHP and
FGSW-2622VHP. The descriptions of these models are shown below:
FGSD-1022VHP 8-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo
Desktop Switch
FGSW-1822VHP 16-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo
Ethernet Switch
FGSW-2622VHP 24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP/SFP Combo
Ethernet Switch
“802.3at PoE+ Switch” is used as an alternative name in this user’s manual.
1.1 Package Contents
Open the box of the 802.3at PoE+ Switch and carefully unpack it. The box should
contain the following items:
802.3at PoE+ Switch x 1 User’s Manual x 1
Power Cord x 1 Accessories x 1
If any of these pieces are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing material,
and use them again to repack the product in case there is a need to return it to us
for repair.

6
1.2 Product Description
Ideal Cost-effective Integration Solution for Secure IP Surveillance
Infrastructure
Particularly designed for the growing popular IP surveillance applications, PLANET
FGSD/FGSW 802.3at PoE+ Switch series is positioned as a surveillance switch with
the central power management and IP camera monitoring.
The FGSD/FGSW 802.3at PoE+ Switch series brings an ideal, secure surveillance
system at a lower total cost. The FGSD/FGSW 802.3at PoE+ Switch series provides
multiple 10/100Mbps 802.3at/af PoE ports able to feed sufcient PoE power for
IEEE 802.3at PoE IP cameras at the same time. It is also able to be connected
with an 8/16/32-channel NVR system, uplinked to the backbone switch and the
monitoring center. With such a high-performance switch architecture, the recorded
video les from the PoE IP cameras can be saved in the NVR system to enable the
administrators to control and monitor the surveillance images both in the local LAN
and the remote sites.
Model FGSD-1022VHP FGSW-1822VHP FGSW-2622VHP
10/100TX Copper 8 x RJ45 16 x RJ45 24 x RJ45
10/100/1000T Copper 2 x RJ45 2 x RJ45 2 x RJ45
1000X Fiber Optic 2 x SFP Slots 2 x SFP Slots 2 x SFP Slots
802.3at/af PoE+ Ports 816 24
PoE Budget 120 watts 300 watts 300 watts
Enclosure 12” metal case 19” metal case 19” metal case
Centralized Power Management for Security and Public Service PoE
Applications
To fulll the needs of the high power consumption of PoE network applications, the
FGSD/FGSW 802.3at PoE+ Switch series features the standard IEEE 802.3at Power
over Ethernet Plus (PoE+) that combines up to 30 watts of power output and data
per port over one Cat5E/6 Ethernet cable. It is designed specically to meet the
demand of the high power consumption of network PDs (powered devices) such
as IR, PTZ, speed dome cameras and even box-type IP cameras with built-in fan
and heater. Compliant with both 802.3at and 802.3af standards, the FGSD/FGSW
802.3at PoE+ Switch series allows more exibility in power requirement for a
variety of PDs, making installation costs affordable.

7
LCD Monitor for Real-time PoE Usage and System Status Display
The LCD monitor of the FGSD/FGSW 802.3at PoE+ Switch series clearly shows the
levels of PoE power usage and system status, such as overload, low voltage, over
voltage and high temperature. With its brand-new LCD monitor, user is able to
obtain detailed information about real-time PoE power usage and real-time system
status of the FGSD/FGSW 802.3at PoE+ Switch series.
1
PWR
PoE Port Status
5 9 13 17 21
3 7 11 15 19 23 25
Gigabit
26
PoE
2 6 10 14 18 22
4 8 12 16 20 24
PoE
FGSW-2622VHP
24-Port 10/100TX 802.3at PoE +2-Port Gigabit
Ethernet Switch
4 6 82
1357
PoE In-Use
ACTLNK
1000
ACTLNK
100
26
25
26
25
12 14 1610
9 11 13 15
20 22 2418
17 19 21 23
Standard
VLAN
PoE Port Status Power Over-voltage Protection Power Over Temperature ProtectionPower Low-voltage Protection
Easy Installation and Cable Connection
As data transfer and High Power PoE are transmitted over a cable, the FGSD/
FGSW 802.3at PoE+ Switch series is able to reduce the need of extended cables
and electrical outlets on the wall, ceiling or any unreachable place. It helps to
lower the installation costs and simplify the installation effort. All RJ45 copper
interfaces of the FGSD/FGSW 802.3at PoE+ Switch series support 10/100Mbps
and 10/100/1000Mbps auto-negotiation for optimal speed detection through RJ45
Category 6, 5 or 5e cable. It also supports standard auto-MDI/MDI-X that can
detect the type of connection to any Ethernet device without requiring special
straight-through or crossover cables.
Flexible and Extendable Uplink Solution
The FGSD/FGSW 802.3at PoE+ Switch series provides 2 extra Gigabit TP/SFP
combo interfaces supporting 10/100/1000BASE-T RJ45 copper for surveillance
network devices such as NVR, video streaming server or NAS to facilitate
surveillance management. Or through these Gigabit speed ber SFP slots, the
1000BASE-SX/LX SFP (Small Form-factor Pluggable) ber transceiver is inserted to
be uplinked to a backbone switch and monitoring center over a long distance. The
distance can be extended from 550m to 2km (multi-mode ber), even going up to
above 10/20/30/40/50/60/70/120km (single-mode ber or WDM ber). They are
well suited for applications within the enterprise data centers and distributions.

8
1.3 Features
Physical Port
FGSD-1022VHP
8-port 10/100BASE-TX Fast Ethernet RJ45 copper
2 10/100/1000BASE-T TP and 2 1000BASE-X mini-GBIC SFP shared
combo interfaces
FGSW-1822VHP
16-port 10/100BASE-TX Fast Ethernet RJ45 copper
2 10/100/1000BASE-T TP and 2 1000BASE-X mini-GBIC SFP shared
combo interfaces
FGSW-2622VHP
24-port 10/100BASE-TX Fast Ethernet RJ45 copper
2 10/100/1000BASE-T TP and 2 1000BASE-X mini-GBIC SFP shared
combo interfaces
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet end-span PSE
Up to 8/16/24 ports of IEEE 802.3af/802.3at devices powered
Supports PoE Power up to 30.8 watts for each PoE port
Each port supports 53V DC power to PoE Powered Device (FGSD-1022VHP)
120-watt PoE budget (FGSD-1022VHP)
Each port supports 54V DC power to PoE Powered Device (FGSW-1822VHP or
FGSW-2622VHP)
300-watt PoE budget (FGSW-1822VHP or FGSW-2622VHP)
Auto detects powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m with standard mode
Switching
Hardware based 10/100Mbps or 10/100/1000Mbps auto-negotiation and auto
MDI/MDI-X
Flow control for full duplex operation and back pressure for half duplex operation

9
Integrates address look-up engine, supporting 4K absolute MAC addresses
IEEE 802.1Q VLAN transparency
Hardware DIP switch for “Standard”, “VLAN” and “Extend” mode selection; the
“Extend” mode features 30-watt PoE transmit distance of 250m at speed of
10Mbps and VLAN isolation (FGSD-1022VHP only)
Hardware DIP switch for “Standard” and “VLAN” mode selection, the “VLAN”
mode for IP surveillance application (FGSW-1822VHP or FGSW-2622VHP only)
Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP
spoong
Automatic address learning and address aging
Hardware
12/19-inch desktop size, 1U height, rack mountable
LED indicators for system power, per port PoE ready and PoE activity, speed,
Link/Act
LCD Monitor for system status and PoE usage status display
1 silent fan to provide stable and efcient power performance (FGSD-1022VHP)
2 silent fans to provide stable and efcient power performance (FGSW-1822VHP
or FGSW-2622VHP)

10
1.4 Specications
Model FGSD-1022VHP FGSW-1822VHP FGSW-2622VHP
Hardware Specications
802.3af/802.3at PoE Injector
Port 816 24
10/100BASE-TX MDI/
MDIX Ports 816 24
10/100/1000BASE-T MDI/
MDIX Ports 2 (Combo Port)
1000BASE-X SFP/mini-GBIC
Slots 2 (Combo Port)
DIP Switch 1
Switch Architecture Store-and-Forward
Switch Fabric 5.6Gbps/
non-blocking
7.2Gbps/
non-blocking
8.8Gbps/
non-blocking
Switch Throughput@64
bytes
4.16Mpps@64
bytes
5.35Mpps@64
bytes
6.54Mpps@64
bytes
MAC Address Table 4K entries
Maximum Frame Size 1536 bytes
Flow Control IEEE 802.3x pause frame for full-duplex;
back pressure for half-duplex
LED
System: Power (Green)
10/100BASE-TX RJ45 Interfaces:
10/100Mbps LNK/ACT (Green)
PoE-in-Use (Orange)
10/100/1000BASE-T RJ45/SFP Interfaces:
LNK/ACT (Green)
100/1000 (Green)
LCD Monitor (W x D) 39.5mm x 24.8mm
System Status/PoE Usage Port Status
Dimensions (W x D x H) 180 x 280 x 44
mm (1U height) 233 x 440 x 44 mm (1U height)
Enclosure Metal
Weight 1.8kg 3.2kg 3.3kg
Power Requirements
AC 100~240V,
50/60Hz, 2.5A
max.
100~240V AC, 50/60Hz, 5A max.