Planet FGSW-1822VHP User manual

16-/24-Port 10/100TX 802.3at PoE
+ 2-Port Gigabit TP + 2-Port SFP Ethernet Switch
with LCD PoE Monitor
FGSW-1822VHP/FGSW-2622VHP
User’s Manual

Copyright
Copyright © 2017 by PLANET Technology Corp. All rights reserved. No part of
this publication may be re-produced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or oth-
erwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specically disclaims any warranties,
merchantability or tness for any particular purpose. Any software described
in this manual is sold or licensed "as is". Should the programs prove defective
following their purchase, the buyer (and not PLANET, its distributor, or its dealer)
assumes the entire cost of all nec-essary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software. Further, PLANET
reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation to notify any person of such revision or
changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Trademarks
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their re-spective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applica-tions, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred. Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET assumes
no respon-sibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in this
User’s Manual, and reserves the right to make improvements to this User’s Manual
and/or to the products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your com-ments and suggestions.

FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted mu-nicipal waste; WEEE should be collected
separately.
Revision
PLANET 16-/24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP + 2-Port SFP
Ethernet Switch with LCD PoE Monitor User's Manual
Models: FGSW-1822VHP, FGSW-2622VHP
Revision: 2.0 (Nov., 2017)
Part No.: 2351-AK5040-000

Table of Contents
1. Introduction ............................................................................................... 5
1.1 Package Contents ................................................................................ 5
1.2 Product Description.............................................................................. 6
1.3 Features ............................................................................................10
1.4 Specications .....................................................................................12
2. Hardware Description .................................................................................14
2.1 Front Panel ........................................................................................14
2.1.1 LCD Monitor Indicators ..............................................................15
2.1.2 LED Indicators ..........................................................................16
2.2 Rear Panel .........................................................................................17
2.3 LCD Management ...............................................................................18
2.3.1 Switch Mode .............................................................................19
2.3.2 Budget Control..........................................................................21
2.3.3 PSE Port Priority........................................................................21
2.3.4 PSE Port Enable ........................................................................22
2.3.5 PD Type ...................................................................................22
2.3.6 Alive Check...............................................................................23
2.3.7 Bandwidth Detection..................................................................24
2.3.8 Fan Control...............................................................................24
2.3.9 Screen Saver ............................................................................25
2.3.10 Language ................................................................................25
2.3.11 Default Setting.........................................................................26
2.3.12 System ...................................................................................26
3. Hardware Installation .................................................................................27
3.1 Desktop Installation ............................................................................28
3.2 Rack Mounting ...................................................................................29
3.3 Installing the SFP Transceiver ..............................................................30
3.4 Product Applications............................................................................32
3.5 Power over Ethernet Powered Devices ..................................................33
4. Power over Ethernet Overview ....................................................................34
5. Troubleshooting .........................................................................................37
Appendix A Networking Connection ..................................................................38
A.1 Switch’s Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T ................38
A.2 10/100Mbps, 10/100BASE-TX ...............................................................38

5
1. Introduction
Thank you for purchasing PLANET 16-/24-Port 10/100TX 802.3at PoE + 2-Port
Gigabit TP + 2-Port SFP Ethernet Switch series, FGSW-1822VHP and FGSW-
2622VHP. The descriptions of these models are shown below:
FGSW-1822VHP 16-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP + 2-Port
SFP Ethernet Switch with LCD PoE Monitor
FGSW-2622VHP 24-Port 10/100TX 802.3at PoE + 2-Port Gigabit TP + 2-Port
SFP Ethernet Switch with LCD PoE Monitor
“802.3at PoE+ Switch” is used as an alternative name in this user’s manual.
1.1 Package Contents
Open the box of the 802.3at PoE+ Switch and carefully unpack it. The box should
contain the following items:
802.3at PoE+ Switch x 1 User’s Manual x 1
Power Cord x 1 Accessories x 1
If any of these pieces are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing material,
and use them again to repack the product in case there is a need to return it to us
for repair.

6
1.2 Product Description
Ideal High-performance Integration Solution for Secure IP Surveillance
Infrastructure
Particularly designed for the IP surveillance applications, PLANET FGSW 802.3at
PoE+ Switch series is perfect for the installation of IP cameras in a remote site,
where its power allocation can be centrally managed.
The FGSW 802.3at PoE+ Switch series is designed for users who are looking
for a high-quality surveillance system but at the cost you will be satised with.
The FGSW 802.3at PoE+ Switch series provides multiple 10/100 Mbps 802.3at/
af PoE ports able to feed numerous IEEE 802.3at PoE IP cameras with sufcient
PoE power. It is also able to be connected with an 8/16/32-channel NVR system,
and uplinked to the backbone switch and the monitoring center. With such a high-
performance switch architecture, the recorded video les from the PoE IP cameras
can be saved in the NVR system to enable the administrators to control and
monitor the surveillance images both in the local LAN and the remote sites.
Model FGSW-1822VHP FGSW-2622VHP
10/100TX Copper 16 x RJ45 24 x RJ45
10/100/1000T Copper 2 x RJ45 2 x RJ45
1000X Fiber Optic 2 x SFP Slots 2 x SFP Slots
802.3af/at PoE+ Ports 16 24
PoE Budget 300 watts 300 watts

7
Simple “Plug and Watch” for a Quick Solution
PLANET FGSW-1822VHP is an ideal Plug and Watch Power over Ethernet solution
which provides quick installation, real-time PoE work status monitoring and
immediate troubleshooting through its unique LCD display to improve work
efciency and quality without any PC or software required.
The FGSW-1822VHP is equipped with 16 10/100BASE-TX ports with each port
taking up 30 watts of PoE+ power and 2 Gigabit TP and 2 Gigabit SFP interfaces
with inner power system. With a total PoE+ power budget of 300 watts and non-
blocking data switching performance, the FGSW-1822VHP can fulll the demand of
sufcient PoE power for HD IP surveillance. It offers a desktop-sized, reliable and
visible power solution for small businesses and system integrators deploying Power
over Ethernet networks.
Smart LCD Power LED
Gigabit TP/SFP
LNK/ACT Status
PoE & LNK/ACT
Status
Menu/Enter/Back
Up/Down Button
2 x Gigabit TP/SFP
16 x 10/100BASE-TX 802.3at PoE+

8
Smart and Intuitive LCD Control
PLANET FGSW 802.3at PoE+ Switch series provides an intuitive color panel on its
front panel that facilitates the Ethernet management and PoE PD management.
They greatly promote management efciency in large-scale network, such as
enterprises, hotels, shopping malls, government buildings, and other public areas,
and feature the following special management and status functions:
PoE management and status
Port management and status
Switch Mode: Standard, VLAN, Extend
Budget and bandwidth control
PD alive check
Maintenance: Screen saver, fan control, factory default and save conguration
4 6 82
1 3 5 7
12 14 1610
911 13 15
20 22 2418
17 19 21 23
FGSW-2622VHP
Menu (5 sec)
Enter
Back
PWR
Up
Down
Gigabit
25 27
26 28
PoE
1
2
5
6
9
10
13
14
17
18
21
22
3
4
7
8
11
12
15
16
19
20
23
24
PoE In-Use
ACTLNK
26
25
28
27
ACTLNK
10/100 1000
Main Menu
01 —
02 —
03 —
05 —
06 —
07 —
08 —
Switch Mode
Budget Control
PSE Port Priority
PD Type
Alive Check
Bandwidth
Fan Control
04 — PSE Port Enable
Switch Mode
Options:
Standard
VLAN
Extend
<
Bandwidth
Use the up and down buttons
to select
PSE Port Enable
Port Status
Enable01
Disable
<
<UP>/<Down>:Select
<Enter>:Confirm <Back>:Return
Current Setting: Enable
System
<Back>: Return
PLANET 802.3af/at PoE Switch
www.planet.com.tw
Model: FGSW-2622VHP
HW ver: V2.0
SW ver: V3.01
Switch Port Information
30.3
01 W ---M-33M
----
02 W ---M---M
----W
03 ---M---M
15.4W
04 -10M---M
----W
05 ---M---M
----
06 W ---M---M
----
07 W ---M---M
----
08 W ---M---M
-8.3
09 W ---M-11M
----
10 W ---M---M
-OFF
11 ----M---M
----
12 W ---M---M
17.6W
13 -11M-12M
----
14 W ---M---M
PB:300W TP:72W PD:4

9
Standard, VLAN and Extend Operation Modes Offered
PLANET FGSW 802.3at PoE+ Switch series provides Standard, VLAN and Extend
operation modes. The FGSW 802.3at PoE+ Switch series operates as a normal
IEEE 802.at/af PoE Switch in the Standard operation mode. The VLAN operation
mode features the port-based VLAN function that can help to prevent the IP
camera’s multicast or broadcast storm from inuencing each other.
VLAN Isolation Mode
Ports 17 and 18
Ports 1~16 Access Permitted
FGSW-1822VHP
PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
1000
1000BASE-SX/LX Fiber-optic
1000
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
IP Camera
IP Camera
IP Camera
NVR
Standard
VLAN <
Extend
In the Extend operation mode, the FGSW 802.3at PoE+ Switch series operates on
a per-port basis at 10Mbps duplex operation but can support 30-watt PoE power
output over a distance of up to 250 meters overcoming the 100m limit on Ethernet
UTP cable. With this brand-new feature, the FGSW series provides an additional
solution for 802.3af/at PoE distance extension, thus saving the cost of Ethernet
cable installation. Its VLAN isolation function isolates ports so as to prevent
broadcast storm and defend DHCP spoong in the Extend operation mode.
Standard Mode (default)
Power
PoE
100 meters (328 feet)
FGSW-1822VHP
PoE
100BASE-TX UTP with PoE
PoE IP Camera
Standard <
VLAN
Extend
Extend Mode
Power
250 meters (820 feet)
PoE
FGSW-1822VHP
PoE
10BASE-T UTP with PoE
PoE IP Camera
Standard
VLAN
Extend <

10
Flexible Extension Solution
PLANET FGSW 802.3at PoE+ Switch series provides 2 extra Gigabit TP and 2 SFP
interfaces supporting 10/100/1000BASE-T RJ45 copper for surveillance network
devices such as NVR, video streaming server or NAS to facilitate surveillance
management.
Or through these Gigabit speed ber SFP slots, the 1000BASE-SX/LX SFP
(Small Form-factor Pluggable) ber transceiver is inserted to be uplinked to a
backbone switch and monitoring center over a long distance. The distance can
be extended from 550m to 2km (multi-mode ber), even going up to above
10/20/30/40/50/60/70/120km (single-mode ber or WDM ber). They are well
suited for applications within the enterprise data centers and distributions.
Robust Protection
PLANET FGSW 802.3at PoE+ Switch series provides contact discharge of ±6KV DC
and air discharge of ±8KV DC for Ethernet ESD protection. It also supports ±6KV
surge immunity to improve product stability and protects users’ networks from
devastating ESD attacks, making sure the ow of operation does not uctuate.
Easy Installation and Cable Connection
As data and power are transmitted over one cable, the FGSW 802.3at PoE+ Switch
series does not need a second cable and electrical outlets on the wall, ceiling or
any unreachable place. Thus, it helps to lower the installation costs and simplify
the installation effort. All the RJ45 copper interfaces of the FGSW 802.3at PoE+
Switch series support 10/100/1000Mbps auto-negotiation for optimal speed
detection through RJ45 Category 6, 5 or 5e cable. It also supports standard auto-
MDI/MDI-X that can detect the type of connection to any Ethernet device without
requiring special straight-through or crossover cables.
1.3 Features
Physical Port
FGSW-1822VHP
16-port 10/100BASE-TX Fast Ethernet RJ45 copper
2 10/100/1000BASE-T TP and 2 1000BASE-X mini-GBIC SFP interfaces
FGSW-2622VHP
24-port 10/100BASE-TX Fast Ethernet RJ45 copper
2 10/100/1000BASE-T TP and 2 1000BASE-X mini-GBIC SFP interfaces
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet end-span PSE

11
Up to 16/24 ports of IEEE 802.3af/at devices powered
Supports PoE Power up to 32 watts for each PoE port
Each port supports 54V DC power to PoE Powered Device
300-watt PoE budget
Auto detects powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m in standard mode and 250m in extend
mode
Smart LCD
LCD switch mode for “Standard”, “VLAN” and “Extend” mode selection;
the “Extend” mode features 30-watt PoE transmit distance of 250m at speed
of 10Mbps and VLAN isolation
Solid LCD switch mode to isolate ports to prevent broadcast storm and defend
DHCP spoong
Power low-voltage, power over-voltage and PSE over-temperature protection
Screen saver, fan control, factory default and save conguration
PoE management
- Total PoE power budget control
- Per port PoE function enable/disable
- PoE port power feeding priority
- Per PoE port power limitation
- PD alive check
Switching
Hardware-based 10/100Mbps or 10/100/1000Mbps auto-negotiation and auto
MDI/MDI-X
Flow control for full duplex operation and back pressure for half duplex opera-
tion
9216bytes packet size
Integrates address look-up engine, supporting 8K absolute MAC addresses
IEEE 802.1Q VLAN transparency
Automatic address learning and address aging
Hardware
19-inch desktop size, 1U height, rack mountable
2-inch color LCD with smart management functions
LED indicators for system power, per port PoE ready and PoE activity, speed,
Link/Act

12
3 silent fans to provide stable and efcient power performance
Supports Energy-Efcient Ethernet (EEE) function (IEEE 802.3az)
Supports contact discharge of ±6KV DC and air discharge of ±8KV DC for
Ethernet ESD protection
Supports ±6KV surge immunity
1.4 Specications
Model FGSW-1822VHP FGSW-2622VHP
Hardware Specications
802.3af/at PoE Injector Port 16 24
10/100BASE-TX MDI/MDIX
Ports 16 24
10/100/1000BASE-T MDI/MDIX
Ports 2
1000BASE-X SFP/mini-GBIC
Slots 2
Switch Architecture Store-and-Forward
Switch Fabric 11.2Gbps/non-blocking 12.8Gbps/non-blocking
Switch Throughput@64 bytes 8.3Mpps@64 bytes 9.5Mpps@64 bytes
MAC Address Table 8K entries
Maximum Frame Size 9216 bytes
Flow Control IEEE 802.3x pause frame for full-duplex; back
pressure for half-duplex
LED
System:
Power (Green)
10/100BASE-TX RJ45 Interfaces:
10/100Mbps LNK/ACT (Green)
PoE-in-Use (Orange)
1000BASE-X SFP Interfaces:
LNK/ACT (Green)
10/100Mbps (Red)
1000Mbps (Green)
LCD Monitor (W x D) 40.6 x 30.5 mm, 2-inch
Buttom Menu, Enter, Back, Up and Down
Dimensions (W x D x H) 233 x 440 x 44 mm (1U height)

13
Enclosure Metal
Weight 3.3kg 3.4kg
Power Requirements 100~240V AC, 50/60Hz, 5A max.
Power Consumption/Dissipation Max. 330watts/1132 BTU
Thermal Fan 3
ESD Protection Contact discharge of ±6KV DC
Air discharge of ±8KV DC
Surge Protection ±6KV
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/PSE
PoE Power Supply Type End-span
PoE Power Output
Per port 53V-54V DC, 300mA. max. 15.4 watts
(IEEE 802.3af)
Per port 53V-54V DC, 600mA. max. 30 watts
(IEEE 802.3at)
Power Pin Assignment 1/2 (+), 3/6 (-)
PoE Power Budget 300 watts
Max. Number of Class 2 PDs 16 24
Max. Number of Class 3 PDs 16 23
Max. Number of Class 4 PDs 11 11
Standards Conformance
Regulatory Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000BASE-T
IEEE 802.3z Gigabit SX/LX
IEEE 802.3x Flow control and back pressure
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3az Energy Efcient Ethernet (EEE)
Environment
Operating Temperature: -10 ~ 60 degrees C
Relative Humidity: 10 ~ 90% (non-condensing)
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)

14
2. Hardware Description
These switches provide three different running speeds – 10Mbps, 100Mbps and
1000Mbps and automatically distinguish the speed of the incoming connection.
This section describes the hardware features of 802.3at PoE+ Switch. For easier
management and control of the 802.3at PoE+ Switch, familiarize yourself with its
display indicators and ports. Front panel illustrations in this chapter display the unit
LED indicators. Before connecting any network device to the 802.3at PoE+ Switch,
please read this chapter carefully.
2.1 Front Panel
The Front Panel of the 802.3at PoE+ Switch consists of 16/24 802.3af/at auto-
sensing 10/100Mbps Ethernet RJ45 ports and 2 Gigabit TP/SFP ports. The LCD
monitor and LED Indicators are also located on the front panel of the 802.3at
PoE+ Switch.
4 6 82
1 3 5 7
12 14 1610
911 13 15
FGSW-1822VHP
Menu (5 sec)
Enter
Back
1
PWR
Up
Down
5 9 13
3 7 11 15
PoE
2 6 10 14
4 8 12 16
PoE In-Use
ACTLNK
Gigabit
17 19
18 20
ACTLNK
10/100 1000
18
17
20
19
16-Port 10/100TX 802.3at PoE +
4-Port Gigabit Ethernet Switch
Switch Port Information
30.3
01 W ---M-33 M
----
02 W ---M--- M
----W
03 ---M--- M
15.4W
04 -10M--- M
----W
05 ---M--- M
----
06 W ---M--- M
----
07 W ---M--- M
----
08 W ---M--- M
-8.3
09 W ---M-11 M
----
10 W ---M--- M
-OFF
11 ----M--- M
----
12 W ---M--- M
17.6W
13 -11M-12 M
----
14 W ---M--- M
PB:300W TP:72W PD:4
Figure 2-1: FGSW-1822VHP Switch Front Panel
4 6 82
1 3 5 7
12 14 1610
911 13 15
20 22 2418
17 19 21 23
FGSW-2622VHP
Menu (5 sec)
Enter
Back
PWR
Up
Down
Gigabit
25 27
26 28
PoE
1
2
5
6
9
10
13
14
17
18
21
22
3
4
7
8
11
12
15
16
19
20
23
24
PoE In-Use
ACTLNK
26
25
28
27
ACTLNK
10/100 1000
Switch Port Information
30.3
01 W ---M-33 M
----
02 W ---M--- M
----W
03 ---M--- M
15.4W
04 -10M--- M
----W
05 ---M--- M
----
06 W ---M--- M
----
07 W ---M--- M
----
08 W ---M--- M
-8.3
09 W ---M-11 M
----
10 W ---M--- M
-OFF
11 ----M--- M
----
12 W ---M--- M
17.6W
13 -11M-12 M
----
14 W ---M--- M
PB:300W TP:72W PD:4
Figure 2-2: FGSW-2622VHP Switch Front Panel
Fast Ethernet TP interface
10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meter.
Gigabit TP Interface
10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters.
Gigabit SFP Slot
1000BASE-SX/LX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver
module: From 550 meters (multi-mode ber) to 10/20/30/40/50/60/70/120 kilo-
meters (single-mode ber).
Smart LCD
The Smart LCD that is located on the front panel of the FGSW-1822VHP, FGSW-
2622VHP 802.3at PoE+ Switch provides “PoE Management and Status”,
“Switch Mode: Standard,VLAN, Extend”,“Budget and Bandwidth
Control”,“Screen Saver”,“Fan Control”, and “Factory Default”.

15
2.1.1 LCD Monitor Indicators
The 802.3at PoE+ Switch has an LCD monitor designed for network administrator
who can easily obtain real-time per PoE port output watts information and system
status display, such as over voltage, low voltage, and PoE chipset over temperature
function. The details of each message on the LCD monitor are shown below:
FGSW-1822VHP/FGSW-2622VHP LCD Display
Power Low-voltage Protection Power Over-voltage Protection PSE Over-temperature Protection
30.3
01 W ---M---M
ULP
02 ---M---M
OLP
03 ---M---M
SCP
04 ---M---M
----W
05 ---M---M
13.6
06 W ---M---M
14.4
07 W ---M---M
----
08 W -33M---M
----
09 W ---M-33M
-OFF
10 - ---M---M
----
11 W ---M---M
----
12 W ---M---M
----
13 W ---M---M
----
14 W ---M---M
PB:300W TP:0W PD:3
Switch Port Information
Switch Port Information
----
01 W ---M---M
----
02 W ---M---M
----W
03 ---M---M
----W
04 ---M---M
----W
05 ---M---M
----
06 W ---M---M
----
07 W ---M---M
----
08 W ---M---M
----
09 W ---M---M
----
10 W ---M---M
----
11 W ---M---M
----
12 W ---M---M
----
13 W ---M---M
----
14 W ---M---M
WARNING！
Main supply voltage
is High！
All ports had shut-
down.
PD:0PB:300W TP:0W
----
01 W ---M---M
----
02 W ---M---M
----W
03 ---M---M
----W
04 ---M---M
----W
05 ---M---M
----
06 W ---M---M
----
07 W ---M---M
----
08 W ---M---M
----
09 W ---M---M
----
10 W ---M---M
----
11 W ---M---M
----
12 W ---M---M
----
13 W ---M---M
----
14 W ---M---M
WARNING！
The PSE device is too
hot!
All ports had shut-
down.
Switch Port Information
PD:0PB:300W TP:0W
----
01 W ---M---M
----
02 W ---M---M
----W
03 ---M---M
----W
04 ---M---M
----W
05 ---M---M
----
06 W ---M---M
----
07 W ---M---M
----
08 W ---M---M
----
09 W ---M---M
----
10 W ---M---M
----
11 W ---M---M
----
12 W ---M---M
----
13 W ---M---M
----
14 W ---M---M
WARNING！
Main supply voltage
is low！
All ports had shut-
down.
Switch Port Information
PD:0PB:300W TP:0W
PD light load protection
PD overload protection
Short-circuit protection
PoE Usage
Network traffic
PoE OFF
Power Budget Total PoE
Output
Number of PDs
Note
1. The LCD screens of the FGSW-1822VHP and FGSW-2622VHP are
the same, except the number of ports and port allocation.
2. The LCD screens of the FGSW-1822VHP and FGSW-2622VHP will
refresh every 15 seconds.
3. For details on LCD Management feature, please refer to “2.3
LCD Management”.
The detailed Smart LCD description of each item is shown below:
Parameters Description
30.3W
(example) It means the output power port of the PoE switch.
OLP It means the port is overloaded corresponding to the PSE, and
the port stops powering.

16
Parameters Description
ULP
It means the port corresponding to the PSE is lightly loaded
and the port stops powering (When the current on the network
is less than 7.5mA, the PSE thinks the PD has been dialed out
and the port stops powering).
SCP It means the port corresponding to the PSE appears to be
short-circuited and the port stops powering.
OFF It means the white and blue OFF shows that the port is blocked
by the menu command.
---W It means the port is without a PD device insert.
---M It means this port does not have data transfers.
<1m It means this port data rate transfers less than 1m.
33m
(example)
The white and blue character represents the data transmission
rate while the red character represents the data transmission
rate which is greater than the bandwidth setting, causing power
to restart the PSE port. If the resumption situation happens for
10 times within 1 hour, the power supply to the port will be cut
off.
PB It means power budget.
TB It means total PoE power output information.
PD The number of PDs inserted.
2.1.2 LED Indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.
10/100Mbps PoE Ports
LED Color Function
LNK/ACT Green
Lights Indicates the link through that port is
successfully established at 10/100Mbps.
Blinks Indicates that the Switch is actively sending
or receiving data over that port.
PoE-in-Use Orange
Lights Indicates the port is providing 53V DC in-line
power.
Off Indicates the connected device is not a PoE
powered device (PD).

17
1000Mbps TP/SFP Slots
LED Color Function
LNK/ACT Green
Lights Indicates the link through that port is
successfully established at 1000Mbps.
Blinks Indicates that the Switch is actively sending
or receiving data over that port.
10/100 Red Lights Indicates the port is successfully established
at 10/100Mbps
1000 Green Lights Indicates the port is successfully established
at 1000Mbps.
2.2 Rear Panel
The rear panel of the 802.3at PoE+ Switch has an AC power socket (100 to 240V
AC, 50-60Hz, 5A).
100~240V AC 50/60Hz, 5A max.
Figure 2-3: FGSW-1822VHP/FGSW-2622VHP Switch Rear Panel
AC Power Receptacle
For compatibility with electrical outlet standard in most areas of the world, the
802.3at PoE+ Switch’s power supply automatically adjusts to line power in the
range of 100-240V AC and 50/60Hz, 5A.
Plug the female end of the power cord rmly into the receptacle on the rear panel
of the 802.3at PoE+ Switch and the other end into an electrical outlet, and the
power will be ready.
Power
Notice
The device is a power-required device, which means it will not
work till it is powered. If your networks should be active all the
time, please consider using UPS (Uninterrupted Power Supply) for
your device. It will prevent you from network data loss or network
downtime. In some areas, installing a surge suppression device
may also help to protect your 802.3at PoE+ Switch from being
damaged by unregulated surge or current to the Switch or the
power adapter.

18
2.3 LCD Management
The operation of the 5 buttons (Menu, Enter, Back, Up and Down) on the panel:
Up
Down
Menu (5 sec)
Enter
Back
Switch Port Information
30.3
01 W ---M-33M
----
02 W ---M---M
----W
03 ---M---M
15.4W
04 -10M---M
----W
05 ---M---M
----
06 W ---M---M
----
07 W ---M---M
----
08 W ---M---M
-8.3
09 W ---M-11M
----
10 W ---M---M
-OFF
11 ----M---M
----
12 W ---M---M
17.6W
13 -11M-12M
----
14 W ---M---M
PB:300W TP:72W PD:4
Press the menu button to switch the “Switch Port Information”.
Press the menu button for about 5 seconds and enter the Main Menu. Choose
a menu item by scrolling up and down, and press the “Enter” key to get to the
menu item you have chosen. Press the “Back” key to return to the previous menu.

19
2.3.1 Switch Mode
There are three modes -- “Standard”, “VLAN” and “Extend” – for selection.
Model FGSW-1822VHP FGSW-2622VHP
Switch Mode Function
Standard
(default)
This mode makes the 802.3at PoE+ Switch operate as a
general switch and all PoE ports operate at 10/100Mbps auto-
negotiation.
VLAN
This mode makes the FGSW-
1822VHP operate as a VLAN
isolation switch and
1. Port 1 to port 16 will isolate
respectively.
2. Port 1 to port 16 can only
communicate with port 17
and port 18 (uplink port).
This mode makes the FGSW-
2622VHP operate as a VLAN
isolation switch and
1. Port 1 to port 24 will isolate
respectively.
2. Port 1 to port 24 can only
communicate with port 25
and port 26 (uplink port).
Extend
With
VLAN
Isolation
This mode makes the FGSW-
1822VHP operate as a VLAN
isolation switch and
1. Port 1 to port 16 will isolate
respectively.
2. Port 1 to port 16 can only
communicate with port 17
and port 18 (uplink port).
3. 30-watt PoE transmit
distance of 250m at speed
of 10Mbps.
This mode makes the FGSW-
2622VHP operate as a VLAN
isolation switch and
1. Port 1 to port 24 will isolate
respectively.
2. Port 1 to port 24 can only
communicate with port 25
and port 26 (uplink port).
3. 30-watt PoE transmit
distance of 250m at speed
of 10Mbps.
Table 2-1: FGSW 802.3at PoE+ Switch Switch Mode Description

20
VLAN Isolation Mode
Ports 17 and 18
Ports 1~16 Access Permitted
FGSW-1822VHP
PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
1000
1000BASE-SX/LX Fiber-optic
1000
100BASE-TX UTP
PoE
100BASE-TX UTP with PoE
IP Camera
IP Camera
IP Camera
NVR
Standard
VLAN <
Extend
Standard Mode (default)
Power
PoE
100 meters (328 feet)
FGSW-1822VHP
PoE
100BASE-TX UTP with PoE
PoE IP Camera
Standard <
VLAN
Extend
Extend Mode
Power
250 meters (820 feet)
PoE
FGSW-1822VHP
PoE
10BASE-T UTP with PoE
PoE IP Camera
Standard
VLAN
Extend <
VLAN Isolation Feature
The 802.3at PoE+ Switch has one feature called VLAN function. When switching
the mode to the “VLAN” position, port 1 to port 16/24 wouldn’t able to
communicate with each other.
4 6 82
1 3 5 7
12 14 1610
911 13 15
FGSW-1822VHP
Menu (5 sec)
Enter
Back
1
PWR
Up
Down
5 9 13
3 7 11 15
PoE
2 6 10 14
4 8 12 16
PoE In-Use
ACTLNK
Gigabit
17 19
18 20
ACTLNK
10/100 1000
18
17
20
19
16-Port 10/100TX 802.3at PoE +
4-Port Gigabit Ethernet Switch
Switch Mode
Options:
Standard
VLAN
<
Extend
VLAN 1: P1 P17 P18
VLAN 2: P2 P17 P18
VLAN 16: P16 P17 P18
Standard
VLAN <
Extend