Planet ICA-700 User manual

CCD Box PoE Internet Camera
ICA-700
Quick Installation Guide

Table of Contents
1. Package Contents ........................................................................................ 3
2. System Requirements .................................................................................. 3
3. Outlook....................................................................................................... 4
4. Physical Installation ..................................................................................... 5
5. Setup Tool Installation.................................................................................. 6
6. Setup Tool Conguration .............................................................................. 9
7. Cam Viewer Lite Installation ........................................................................14
Appendix A: Feature Listing for Cam Viewer......................................................18
Appendix B: Suggest Hardware / System Requirement ......................................19
Appendix C: Ordering Information for Cam Viewer Pro.......................................20

3
1. Package Contents
● 1 x ICA-700
● 1 x Power Adapter
● 1 x Camera Stand
● 1 x CD
● 1 x Quick Installation Guide
2. System Requirements
Network Interface 10/100Base-TX Ethernet
Monitoring System Recommended for Internet Explorer 6.0 or above
System Hardware
● CPU: Pentium 4, 1.5GHz or above
● Memory Size: 512 MB or above
● VGA card resolution: 1024 x 768 or above
Optional:
● Sound Card (for PC)
● Microphone (for PC and ICA-700)
● Speaker (for PC and ICA-700)

4
3. Outlook
Rear panel of ICA-700
Port Description
AUDIO IN An external microphone can be plugged in.
AUDIO OUT An external speaker can be plugged in.
RESET
Reset to manufacturer default valued and reboot.
When pressed and held over 10 seconds, the settings of IP
Camera will be set to the default values.
DC 12V
Connect the supplied power adapter.
When this device is obtaining power from PoE, you don’t have to
attach the power adapter.

5
LAN (PoE)
Connect your Camera to a 10/100Base-TX hub or switch. It is
compliant with IEEE 802.3af PoE. Either mid-span PSE or end-
span PSE supported.
4. Physical Installation
1. Connect an Ethernet cable
Connect one end of an Ethernet cable to the LAN port located on the IP camera’s
rear panel and connect the other end to the network device (hub or switch).
2. Attach the external power supply
Attach the provided power adapter to the IP camera’s connector labeled “DC 12V”
on the rear panel. If this camera is obtained power from PoE, you don’t have to
attach the power adapter.
Note
Please use the power adapter that is bundled in package. Using a
power supply with a different voltage rating will damage and void
the warranty for this product.
3. Connect Microphone and Speaker
If you will use the 2-Way audio function, please connect microphone to Audio In
and speaker to Audio Out.

6
5. Setup Tool Installation
Initial setup should be performed by using the supplied Windows-based Setup Tool
as follows:
1. Insert the bundled product CD into CD-ROM drive to launch the autorun pro-
gram.
2. When the web page displayed, select and click the “Setup Tool” hyperlink on the
menu to start the installation process.
Note
If the CD’s menu does not appear, click “Start” on the task bar
and select “Run” to type “X:\Utility\SetupTool.exe”, assume X
is your CD-ROM drive
3. Click “Yes” to start the Setup Tool Installation.
4. Choose the language you need, and click “Next” to continue.

7
5. Follow the step for install the Setup Tool, and click “Next” to continue.
6. If you wish to install the Setup Tool in an alternative location, click “Browse”
and dene a location; otherwise click “Next” to continue.
7. If you wish to install the Setup Tool in an alternative folder of start menu, type
a new folder name or select a exiting folder; otherwise click “Next” to continue.

8
8. Check the installation summary, and click “Install” to start the installation.
9. The Setup Tool will be start install to your computer.
10. The Setup Tool installation successful. Click “Finish” to complete the installa-
tion. If you would like to run the Setup Tool, please check “Launch Program
le” before click Finish button.

9
6. Setup Tool Conguration
This section shows how to perform basic conguration functions by Setup Tool.
1. Double click the icon of Setup Tool on the desktop.
2. The Setup Tool screen will show up as below. It will automatically search and list
the IP cameras on your network.
3. Select the IP camera you want, and then click the “Setup” button on the right
side. The login window will pop up. If the Administrator User Name and Pass-
word have been changed, you will need to enter the new settings. In default val-
ues, please enter “admin” for both User Name and Password. Then click “OK”.

10
4. On the following System information screen, it displays the Product Name, Firm-
ware Version and Hardware Version. Click on “Next” to continue.
5. On the following Account settings screen, you can modify the Administrator login
user name and password. And you can add some user accounts as Admin, Op-
erator or Viewer. Please click “Next” to continue.