Planet ICA-750 User manual

Dual Mode CCD Box Internet Camera
ICA-750
Version 1.0
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. System Requirements ................................................................................. 4
3. Outlook...................................................................................................... 5
3.1 Front Panel ........................................................................................... 5
3.2 Rear Panel ............................................................................................ 6
4. Physical Installation .................................................................................... 7
5. SetupWizardConguration ......................................................................... 8

3
1. Package Contents
● 1xICA-750
● 1xCameraStand
● 1xPowerAdapter
● 1xAllenWrench
● 2xQuickInstallationGuide
● 1xCD-ROM
Note
Pleaseusethepoweradapterinthispackage.Usingapowersupply
with a different voltage rating will damage and void the warranty
forthisproduct.

4
2. System Requirements
Network Interface 10/100Base-TXEthernet
Monitoring System RecommendedforInternetExplorer6.0orlater
System Hardware
●CPU:Pentium4,1.5GHzorabove
●MemorySize:512MBorabove
●VGAcardresolution:1024x768orabove
●Network bandwidth : In VGA resolu-
tion mode, minimum upload bandwidth is
1Mbps.
Optional:
●SoundCard
●Microphone(forPC)
●Speaker(forPCandICA-750)

5
3. Outlook
3.1 Front Panel
LED Status LED Description
PWR
Off Nopower.
On Poweron.
Blinking ThePowerLEDwillblinkduringstartup(15~20sec).
LAN
Off LANconnectionisnotdetected.
On LANconnectionisdetected.
Blinking DataisbeingtransmittedorreceivedviatheLAN
connection.
LAN
Microphone
PWR

6
3.2 Rear Panel
Reset LAN (PoE)
PWR AUDIO
IN
AUDIO
OUT
DI / DO
I/O Info
PORT PORT Description
Reset
Resettomanufacturerdefaultvaluedandreboot.
Whenpressedandheldover10seconds,thesettingsofIP
Camerawillbesettothedefaultvalues.
Uponcompletion,thePWELEDwillblinkthreetimes.
LAN(PoE)
ConnectyourCameratoa10/100Base-TXhuborswitch.Itis
compliantwithIEEE802.3afstandardPoE.Bothmid-span&
end-spancanbeused.
PWR
Connecttothesuppliedpoweradapter12VDC,1A.Whenthis
deviceisobtainingpowerfromPoEalready,youdon’thaveto
attachthepoweradaptertoICA-750.
DI/DO Theterminalblockincludes2inputportsand2outputports.
AUDIOIN Anexternalmicrophonecanbepluggedin.Thatwilldisablethe
built-inmicrophoneonthefrontpanel.
AUDIOOUT Anexternalspeakercanbepluggedin.

7
4. Physical Installation
1.ConnectanEthernetcable
 ConnectoneendofanEthernetcabletotheLANportlocatedontheIPcamera’s
rearpanelandconnecttheotherendtothenetworkdevice(huborswitch).
2.Attachtheexternalpowersupply
 Attach the provided power adapter to the IP camera’s connector labeled “PWR”
on the rear panel.
3.ChecktheLEDs
a.The Power LED will turn on briey, and then start blinking during startup. Af-
terstartupiscompleted,thePowerLEDwillremainON.
b.TheLANLEDwillbeON.

8
5. Setup Wizard Conguration
Initial setup should be performed by using the supplied Windows-based Setup
Wizardasfollows:
1.Insert the bundled Product CD into CD-ROM drive to launch the autorun pro-
gram.
2.Afterthewebpage displayed,clickthe“Setup Wizard” hyperlink on the menu
tostartthecongurationprocess.
Note
If the CD’s menu does not appear, click “Start” on the task bar
andselect“Run”totype“X:\Utility\SetupWizard\SetupWizard.
exe”,assumeXisyourCD-Romdrive.
3.Thewelcomescreenappears.Clickon“Setup Camera”buttontostartthewiz-
ard.

9
4.Afterclickingthesetupcamerabutton,itwillautosearchfortheIPCamerason
yournetwork.Clickon to continue.
5.The next screen below will list the IP Camera on your network. Select it from
the list on the left side, the current settings table will be displayed on the right
side. Click on to continue.

10
6.The administrator login window will pop up. If the Administrator Name and Ad-
ministrator Password have been set, you will be prompted to enter them. If us-
ing the default values, please enter “admin” for both the name and the pass-
word.Clickon“OK” to continue.
7.On the following Camera Settings screen, you can ll and congure the Device
Name, Description, Time Zone, Local Date and time here. Click on to con-
tinue.