Planet ICA-H652 User manual

H.264 36x Outdoor Speed Dome Internet Camera
ICA-H652
Quick Installation Guide
Version 1.1

Table of Contents
Verify The Contents Inside Package Box ............................................................ 3
Physical Installation ......................................................................................... 4
Further Conguration ......................................................................................12

3
Verify The Contents Inside Package Box
The package should contain the below items. If any item is missing or damaged,
please contact the seller immediately.
Dome Camera with
Outdoor Mount Kit
Compact Pendent Mount Data Cable
Waterproof Rubber Dome Cover Bracket screws kit
Security Tool Lubricant M3/M5 Standard Screw
M3/M5 Security Screw
AC Power Adapter
Quick Installation Guide CD-ROM Power Cord

4
Physical Installation
Caution
1. During the installation, please take care and avoid crash. That
may cause the device damage or cause injury of the installer.
2. Please make sure the hardware had been located on the wall
properly. If the hardware drops down, it is possible make
someone injury or hurt. Please check the hardware again after
the installation.
3. Please according to the practical local power voltage to adjust
the power switch. The wrong input voltage may cause the
device damage.
Step 1
Unpack the Dome Camera’s package and take out the Dome Camera unit.
Step 2
Rotate the Outdoor Mount Kit, and take it off from the camera body.

5
Step 3
Attach the dome cover to the camera body. Before doing that, apply some lubricant
on the cover’s water-proof rubber to make the installation process smoother.
Note
The tiny protrusion on the dome cover must align with one of the
four holes on the dome body.
Step 4
Gently pressure the dome cover downward with two hands on the side of it.
DO NOT press the cover, as shown in the gure; this might cause damage to the
camera body.

6
Step 5
Use the M3 screw to screw the dome cover and camera body together.
Step 6
Make a cable entry hole on the wall to recess the cables. Otherwise, users could
push up the Cable Entry Board on the Compact Pendent Mount’s Mounting Plate to
place the cables, as shown in the photo below.

7
Step 7
Fix the Compact Pendent Mount on the wall with proper screws and screw anchors.
Note
The screws and screw anchors don’t attach in package
Step 8
Attach the Waterproof Rubber to the Outdoor Wall Mount.

8
Step 9
Pass the network and data cables through the Compact Pendent Mount with the
Data Cable’s 22-pin cable coming out of the outlet.
Note
1. The network cable doesn’t attach in package
2. Please block the cable entry hole with the supplied sponge to
avoid insects entering the Pendent Mount. The sponge can be
placed in two ways as shown in the illustrations below.
Step 10
Thread the cables through the Outdoor Mount Kit and join the Outdoor Mount Kit
to the Compact Pendent Mount with the supplied screws and washers. Then adjust
the Waterproof Rubber to the joint.

9
Step 11
Use the safety hook hanging the camera, and connect the cables to the Dome
Camera.

10
Step 12
Join the Dome Camera to the Outdoor Mount Kit with the supplied M5 screw and
washers.
Step 13
Connecting power wires of AC adapter with Power Input connector of data cable.
Please check the color of power wire carefully, and screwed that with connector
properly.
Blue Yellow/Green
Brown
Black Green
White

11
Step 14
Connecting the AC power adapter with Power Input connector of data cable.
Then according to the practical local power voltage to adjust the power switch, and
connect the power cord with adapter and power outlet.
Voltage Switch
Note
Use only the power adapter shipped with the unit to ensure correct
functionality
Step 15
Connecting the network cable with switch.
ICA-H652

12
Step 16
Set your computer’s IP address to 192.168.0.x, where x is a number between 1 to
253 (except 20 where is being used for the camera by default). If you don’t know
how to do this, please ask your network administrator.
Step 17
Use web browser (Internet Explorer 6.0 or above) to connect to 192.168.0.20
(type this address in the address bar of web browser).
You’ll be prompted to input user name and password: admin / null (without
password).
Further Conguration
For detail conguration, please check user’s manual on the bundled CD.
If you have any other questions, please contact the dealer where you purchased
this product or you can contact PLANET directly at the following
Email address: [email protected]