Planet HPOE-460 User manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Introduction
1.1 Checklist
Thank you for purchasing our HPOE-460 4-Port Gigabit
IEEE 802.3at High Power over Ethernet Injector Hub,
the High Power over Ethernet Injector Hub package shall
contains following contents:
Check the contents of your package for following
parts:
High Power over Ethernet Injector Hub x 1
User's Manual x 1
Power Adapter x 1
Power Cord x 1
If any of these pieces are missing or damaged, please
contact your dealer immediately, if possible, retain the
carton including the original packing material, and use
them against to repack the product in case there is a
need to return it to us for repair.
1.3 Features
8-Port RJ-45
4-Port 10/100/1000Mbps “Data input”
4-Port 10/100/1000Mbps “Data + Power output”
Power over Ethernet
IEEE 802.3at and IEEE 802.3af Power over Ethernet
Mid-Span PSE
Up to 4 IEEE 802.3at / 802.3af devices powered
DC 52V power over RJ-45 Ethernet cable to devices
with Ethernet port
PoE power up to 30.8 Watts (802.3at PoE) / 15.4
Watts (802.3af PoE) for each PoE ports
Remote power feeding up to 100m
Full power support for per POE port
Automatically detect powered device (PD)
Circuit protection prevents power interference
between ports
1.5 Product Outlook
1234
4-Port High Power PoE Injector Hub
IEEE 802.3at
52V~56V DC
PWR123
PoE in-Use
4
1 2 3 4
DATA & PWR
Remove “DATA & PWR”
Connection before power on.
CAUTION
DATA
LED Denition:
LED Color Function
Power Green Lights to indicate that the
HPOE-460 has power.
PoE Ready /
In-Use Green Lights to indicate the port is providing 52V DC in-line power.
1.4 Specication
Product HPOE-460
Hardware
Interface
“Data” Input Ports 4 x RJ-45
“Data+Power”
Output Ports 4 x RJ-45
Data Rate 10/100/1000Mbps
LED
System: Power x 1 (Green)
Per PoE Port: PoE ready /
in-use x 4 (Green)
Network Cable
10Base-T: 4-Pair UTP Cat. 5
up to 100m (328ft)
100Base-TX: 4-Pair UTP
Cat. 5 up to 100m (328ft)
1000Base-T: 4-Pair UTP Cat.
5e, 6, up to 100m (328ft)
EIA/TIA-568 100-ohm STP
(100m, 328ft)
Dimension (H x W x D) 26 x 70 x 97mm
Weight 220g
Power Requirement DC 52V~56V
1.2 About the Power over Ethernet Injector
Hub
The PLANET HPOE-460 is the next generation 4-Port
Gigabit IEEE 802.3at High Power PoE injector Hub,
features both IEEE 802.3af and High Power IEEE
802.3at Power over Ethernet (PoE) that combines up
to 30 Watts power output and data per port over one
CAT 5E / 6 Ethernet cable. It is designed specically to
satisfy the growing demand of higher power consuming
network PD (powered devices) such as PTZ (Pan, Tilt &
Zoom) / Speed Dome network cameras, multi-channel
(802.11a/b/g/n) wireless LAN access points and other
network devices by providing double amount of PoE
power than conventional 802.3af PoE PSE.
The HPOE-460 is installed between a regular Ethernet
Switch and the powered devices; it injects power to the
PDs without affecting data transmission performance.
It offers a cost effective and quick solution to upgrade
network system to IEEE 802.3af / IEEE 802.3at Power
over Ethernet system without replacing the existing
Ethernet Switch. There are 8 RJ-45 STP ports on the
front panel of the HPOE-460, half of the ports on right
panel function as “Data input" and the other half
on left panel function as "PoE (Data and Power)
output". The 4 "PoE (Data and Power) output”
ports are also the power injectors that transmit DC
voltage to the CAT. 5/5e/6 cable and transfer data
and power simultaneously between the Injectors and
Splitters.
Hardware
Desktop palm size, wall mountable
LED indicator power input indication
FCC Part 15 Class B, CE
100~240V AC, 50/60Hz, 2A universal power supply
adapter with DC 52V / 2.31A power output
Plug & play
Standard Compliance
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3at pre-standard Power over Ethernet
IEEE 802.3af Power over Ethernet
2. Hardware Installation
This product provides three different running speeds –
10Mbps, 100Mbps and 1000Mbps in the same device
and automatically distinguishes the speed of incoming
connection.
This section describes the hardware features of HPOE-
460. Before connecting any network device to the HPOE-
460, read this chapter carefully.
2.1. Before Installation
Before your installation, it is recommended to check
your network environment. If there is any IEEE 802.3af
/ 802.3at device need power on, the HPOE-460 provide
you a way to supply power for this Ethernet device
conveniently and easily. The HPOE-460 equips with an
AC-DC adapter with DC 52V input and injects this DC
power into the pin of the twisted pair cable (pair 4, 5
and pair 7, 8).
If there is very difcult to nd a power socket for AC-DC
Adapter of your non-IEEE 802.3af / 802.3at networked
device, the HPOE-460 and POE-161S can provide you
a way to supply DC power for this Ethernet device
conveniently and easily.
The 10Mbps or 100Mbps and 1000Mbps speed, duplex
mode from Data port of HPOE-460 depends on which
Ethernet device attached.
Power over Ethernet
PoE Power Supply Type Mid-Span
PoE Power Output Per Port DC 52V 30.8 Watts
/ 15.4 Watts
Power Pin Assignment 4/5(+), 7/8(-)
PoE Power Budget 120 Watts
Number of 802.3af PD Class
0, 1, 2, 3 can be powered 4
Number of 802.3at PD Class
1, 2, 3 can be powered 4
Number of 802.3at PD Class
0, 4 can be powered 4
Standards Conformance
Standards Compliance
IEEE 802.3 10Base-T
Ethernet
IEEE 802.3u 100Base-TX
Fast Ethernet
IEEE 802.3ab 1000Base-T
Gigabit Ethernet
IEEE 802.3at Power over
Ethernet (Pre-standard)
IEEE 802.3af Power over
Ethernet
Regulation Compliance FCC Part 15 Class B, CE
Environment
Operating Temperature 0 ~ 50 Degree C
Storage Temperature -10 ~ 70 Degree C
Humidity 5 ~ 95% (Non-condensing)

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
2.2 HPOE-460 and POE-161S, the IEEE
802.3at Injector / Splitter and Equipment
Installation
For the places hard to nd the power inlet, the
HPOE-460 and IEEE 802.3at High Power over Ethernet
Splitter (POE-161S) provides the easiest way to power
your Ethernet devices such as IP Camera on the ceiling
and the Wireless Access Point installed on the top of the
building. With 4 10/100/1000Base-T Gigabit Ethernet
ports, the HPOE-460 supports full 52V DC power for any
remote IEEE 802.3af / 802.3at powered device (PD).
To control the power system of your networking devices,
the HPOE-460 can directly co-work with PoE IP phone to
build VoIP telephony network in the ofce. Furthermore,
the HPOE-460 can be directly connected to any third
party IEEE 802.3af / 802.3at compliant devices installed
100 meters away.
3. Troubleshooting
This chapter contains information to help you solve
issue. If the High Power over Ethernet Injector Hub
is not functioning properly, make sure the High Power
over Ethernet Injector Hub was set up according to
instructions in this manual.
How to let my non IEEE 802.3af / 802.3at network
devices can work with HPOE-460?
Solution:
You can use PLANET Power over Ethernet Splitter, such
as PLANET POE-152S / POE-161S to work as a power
transformer between HPOE-460 and non IEEE 802.3af /
802.3at devices. The POE-152S and POE-161S provide
5V DC and 12V DC voltage output through DIP switch.
The HPOE-460 PoE LED is not lit
Solution:
Check the cable connection between HPOE-460 and IEEE
802.3af / 802.3at devices.
DC Power Line (DC)
Power Line
1000Base-T UTP
PoE
1000Base-T UTP with PoE
8-Port Gigabit Switch
HPOE-460
802.3at PoE
PTZ / Speed Dome
IP Camera
30W
802.3af PoE
IP Camera
15W
802.3at PoE Splitter+
Non-PoE Device
802.3at
PoE Splitter
DC
802.3at PoE Multi-Channel
/ High Power
Wireless AP
30W
a
N
PoE
PoE
PoE
PoE
Power
Figure 2-1: HPOE-460 Application Topology
Note
1. According to IEEE 802.3af standard and
IEEE 802.3at pre-standard, the
HPOE-460 will not inject power to the
cable if not connecting to IEEE 802.3af
and IEEE 802.3at pre-standard devices.
2. Due to the capability of IEEE 802.3af
standard and IEEE 802.3at pre-standard,
the HPOE-460 can directly connect with
any IEEE 802.3af standard or IEEE
802.3at pre-standard compliant
end-nodes.
Why I connect my PoE device to HPOE-460 and it
cannot power on?
Solution:
1. Please check the cable type of the connection from
HPOE-460 to the other end. The cable should be an
8-wire UTP, Category 5/5e/6, EIA568 cable within 100
meters. A cable with only 4-wire, short loop or over
100 meters, all will affect the power supply.
2. Please check and assure the device that fully complied
with IEEE 802.3af standard and IEEE 802.3at
pre-standard.
Appendix A Networking Connection
RJ-45 Pin Assignments
1000Mbps, 1000Base T
RJ-45 Connector pin assignment
Contact MDI MDI-X
1BI_DA+ BI_DB+
2BI_DA- BI_DB-
3BI_DB+ BI_DA+
4BI_DC+ BI_DD+
5BI_DC- BI_DD-
6BI_DB- BI_DA-
7BI_DD+ BI_DC+
8BI_DD- BI_DC-
Implicit implementation of the crossover function
within a twisted-pair cable, or at a wiring panel, while
not expressly forbidden, is beyond the scope of this
standard.
10/100Mbps, 10/100Base-TX
RJ-45 Connector pin assignment
Contact MDI MDI-X Media
Dependant Interface
MDI-X Media Dependant
Interface -Cross
1Tx + (transmit) Rx + (receive)
2Tx - (transmit) Rx - (receive)
3Rx + (receive) Tx + (transmit)
4, 5 IEEE 802.3af / 802.3at DC 48V / 52V
6Rx - (receive) Tx - (transmit)
7, 8 IEEE 802.3af / 802.3at DC 0V
The standard RJ-45 receptacle / connector
There are 8 wires on a standard UTP/STP cable and
each wire is color-coded. The following shows the pin
allocation and color of straight cable and crossover cable
connection:
Straight Cable
SIDE 1
SIDE 1
SIDE 2
SIDE 1
SIDE 2
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
12345678
12345678
SIDE 2
Crossover Cable
SIDE 1 SIDE 2
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
1 = White/Orange
2 = Orange
3 = White/Green
4 = Blue
5 = White/Blue
6 = Green
7 = White/Brown
8 = Brown
1 = White/Green
2 = Green
3 = White/Orange
4 = Blue
5 = White/Blue
6 = Orange
7 = White/Brown
8 = Brown
Figure A-1: Straight-Through and Crossover Cable
Please make sure your connected cables are with
same pin assignment and color as above picture before
deploying the cables into your network.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device
from the power circuit.
Without removing power cable, the device wills still consuming power
from the power source. In the view of Saving the Energy and reduce the
unnecessary power consuming, it is strongly suggested to remove the
power connection for the device if this device is not intended to be active.