Planet FGSD-910P User manual

8-Port 10/100Mbps 802.3af PoE+
1-Port 10/100/1000Mbps Desktop Switch
FGSD-910P
User’s Manual

Trademarks
Copyright © PLANET Technology Corp. 2013.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and does not
represent a commitment on the part of PLANET. PLANET assumes no responsibility
for any inaccuracies that may be contained in this User’s Manual. PLANET makes
no commitment to update or keep current the information in this User’s Manual,
and reserves the right to make improvements to this User’s Manual and/or to the
products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from
the power circuit.
Without removing power cable, the device will still consuming power from the
power source. In the view of Saving the Energy and reduce the unnecessary power
consuming, it is strongly suggested to remove the power connection for the device
if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste; WEEE has to be collected
separately.
Revision
PLANET 8-Port 10/100Mbps 802.3af PoE + 1-Port 10/100/1000Mbps Desktop Switch
User’s Manual
For Model: FGSD-910P
Revision: 1.0 (JUNE, 2013)
Part No.: 2351-AK3140-000

Table of Contents
1. Introduction ............................................................................................... 5
1.1 Checklist............................................................................................. 5
1.2 Product Description.............................................................................. 5
1.3 Features ............................................................................................. 6
1.4 Specications ...................................................................................... 7
2. Hardware Description .................................................................................. 9
2.1 Front Panel ......................................................................................... 9
2.1.1 LED Indicators ........................................................................... 9
2.2 Rear Panel .........................................................................................10
2.3 Desktop Installation ............................................................................11
2.4 Rack Mounting ...................................................................................12
2.5 Product Application .............................................................................14
2.5.1 802.3af PoE IP Surveillance in Public Transportation .....................14
2.5.2 IP Ofce Department / Workgroup PoE Switch .............................15
2.6 Power over Ethernet Powered Device ...................................................16
3. Power over Ethernet Overview ....................................................................17
4. Troubleshooting .........................................................................................20
Appendix: A Networking Connection .................................................................21
A.1 PoE RJ-45 Port Pin Assignments...........................................................21
A.2 Switch's Data RJ-45 Pin Assignments - 1000Mbps, 1000Base-T ..............21
A.3 10/100Mbps, 10/100Base-TX ...............................................................22

5
1. Introduction
1.1 Checklist
Check the contents of your package for the following parts:
FGSD-910P x 1
l
User's Manual x 1
l
Power Cord x 1
l
Two 19” Rack-mounting Brackets with Attachment Screws x 8
l
If any of these pieces are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing material,
and use them again to repack the product in case there is a need to return it to us
for repair.
The term “PoE Ethernet Switch”mentioned in this user’s manual also means the
FGSD-910P.
1.2 Product Description
Centralized Power Distribution for Ethernet Networking
To fulll the demand of sufcient PoE power for network applications with Fast
Ethernet speed transmission, the FGSD-910P, a new member in the 802.3af PoE
Fast Ethernet Switch family is an 8-Port 10/100Mbps 802.3af Power over Ethernet
+ 1-Gigabit Port Switch with a total of 130 watts of PoE budget, which is an ideal
solution. The eight 802.3af PoE ports provide PoE power injector function which
is able to drive 8 IEEE 802.3af compliant powered devices. The FGSD-910P also
provides a simple, cost-effective and non-blocking wire-speed performance. It
comes with a 12-inch metal compact housing, suitable for desktop deployment in
SOHO ofce or department network application.
Ideal Solution for Securing IP Surveillance Infrastructure
Particularly designed for the growing popular IP Surveillance applications, the
FGSD-910P 802.3af PoE Switch is positioned as a Surveillance Switch with central
management of remote Power control and IP camera monitoring. The FGSD-
910P provides 802.3af PoE functions along with 8 10/100Base-TX ports featuring
15.4-watt 802.3af PoE in RJ-45 copper interfaces and 1 extra Gigabit TP interface
supporting high speed transmission of surveillance images and videos.
Perfectly Integrated Solution for IP PoE Camera and NVR System
Different from the general IT industrial PoE Switch which usually comes with 12 or
24 PoE ports, the FGSD-910P provides 8 802.3af PoE ports for catering to small

6
scale of IP Surveillance networks at a lower total cost. The FGSD-910P comes with
high performance switch architecture and 130-watt PoE power budget. The recorded
video les from 8 PoE IP Cameras can be powered by FGSD-910P and saved in the
8-channel NVR system or surveillance software to perform comprehensive security
monitoring. For instance, one FGSD-910P can combine with one 8-channel NVR and
8 PoE IP cameras as a kit for the administrators centrally and efciently manage
the surveillance system in the local LAN and the remote site via Internet.
Stable and High Performance Switch Architecture
The FGSD-910P has a 4K MAC address table, featuring high performance switch
architecture capable of providing the non-blocking 3.6Gbps switch fabric and
wire-speed throughput as high as 2.67Mpps, which greatly simplies the tasks of
upgrading the LAN for catering to increasing bandwidth demands. Besides, the
802.3x Full-Duplex ow control function of the FGSD-910P enables PD devices and
servers directly connect to the switch for wire-speed packet transfer performance
without risk of packet loss.
The FGSD-910P RJ-45 copper interfaces support 10/100Mbps Auto-Negotiation
at port 1 to port 8 and 10/100/1000Mbps Auto-Negotiation at port 9 for optimal
speed detection through RJ-45 Category 6, 5 or 5e cables. It also supports
standard Auto-MDI/MDI-X that can detect the type of connection to any Ethernet
device without requiring special straight or crossover cables.
Easy Cable Connection
With data and power over Ethernet from one unit, the FGSD-910P reduces cabling
requirements and eliminates the need for dedicated electrical outlets on the wall,
ceiling or any unreachable place. A wire carries both data and power lowering the
installation costs, simplifying the installation effort and eliminating the need for
electricians or extension cords. Providing 8 PoE interfaces, the FGSD-910P is ideal
for small businesses and workgroups requiring to deploy the PoE for the wireless
access points, IP-based surveillance camera or IP phones in any places easily,
efciently and cost-effectively.
1.3 Features
RJ-45 Interface
8-Port 10/100Mbps Fast Ethernet Switch
8-Port supports 48V DC power to PoE Powered Device
1-Port 10/100/1000Mbps Gigabit Ethernet Switch

7
Power over Ethernet
Complies with IEEE 802.3af Power over Ethernet End-Span PSE
Up to 8 IEEE 802.3af devices powered
Supports PoE Power up to 15.4 watts for each PoE port
130-watt PoE budget
Auto detect powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m
Switching
Hardware based 10/100Mbps Auto-Negotiation and Auto MDI/MDI-X (Port 1 to
Port 8)
Hardware based 10/100/1000Mbps Auto-Negotiation and Auto MDI/MDI-X
(Port 9)
Flow control for Full Duplex operation and back pressure for Half Duplex oper-
ation
Integrates address look-up engine, supporting 4K absolute MAC addresses
Automatic address learning and address aging
Hardware
12-inch desktop size, 1U height
LED indicators for system Power, per port PoE ready and PoE activity, speed,
Link / Act
 1 silent FAN to provide stable and efcient power performance
1.4 Specications
Model FGSD-910P
Hardware Specication
Network Connector 8-Port RJ-45 for 10/100Base-TX (Port 1 to Port 8)
1-Port RJ-45 for 10/100/1000Base-T (Port 9)
PoE Inject Port 8-Port with 802.3af PoE injector function

8
LED Display
System: Power (Green)
Per PoE port: PoE (Orange)
LNK/ACT (Green)
Gigabit port: Speed (Green)
LNK/ACT (Green)
Switch Architecture Store and Forward switch architecture
MAC Address Table 4K MAC address table with Auto learning function
Switch Fabric 3.6Gbps
Switch Throughput 2.67Mpps@64Bytes
Flow Control Back pressure for Half-Duplex. IEEE 802.3x Pause
Frame for Full-Duplex
Power Requirements AC 100~240V, 50/60Hz, 2A max.
Power Consumption 150 watts / 511BTU
Dimensions (W x D x H) 280 x 180 x 43mm (W x D x H), 1U height
Weight 1.7kg
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
PoE Power Supply Type End-Span
PoE Power Output Per Port 48V DC, 350mA. Max. 15.4 watts
Power Pin Assignment 1/2(+), 3/6(-)
PoE Power Budget 130 watts (at room temperature)*
Max. number of Class 1PD 8
Max. number of Class 2PD 8
Max. number of Class 3PD 8
Standard Conformance
EMI Safety FCC Class A, CE
Operating Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, Relative Humidity, non-condensing
Storage Humidity 5 ~ 95%, Relative Humidity, non-condensing
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3ab
IEEE 802.3x
IEEE 802.3af
Ethernet
Fast Ethernet
Gigabit Ethernet
Flow Control
Power over Ethernet
* Remarks: POE Power budget may be reduced if the operating temperature rises.

9
2. Hardware Description
This product provides three different running speeds – 10Mbps and 100Mbps at
port 1 to port 8, 10/100/1000Mbps at port 9 and automatically distinguishes the
speed of incoming connection.
This section describes the hardware features of the FGSD-910P. For easier
management and control of the Switch, familiarize yourself with its display
indicators, and ports. Front panel illustrations in this chapter display the unit LED
indicators. Before connecting any network device to the FGSD-910P, please read
this chapter carefully.
2.1 Front Panel
The Front Panel of the FGSD-910P PoE Ethernet Switch consists of 8x Auto-Sensing
10/100Mbps Ethernet RJ-45 Ports and 1x Auto-Sensing 10/100/1000Mbps Ethernet
RJ-45 Port. The LED Indicators are also located on the front panel of the FGSD-
910P.
PoE
8-Port 10/100Mbps+1 Gigabit 802.3af PoE Switch
FGSD-910P
1
PWR
234567
Speed
10/100
LNK/
ACT Gigabit
8 89
ACTLNK
8 97654321
Figure 2-1: FGSD-910P Switch Front Panel
2.1.1 LED Indicators
System
LED Color Function
PWR Green Light: Indicate the Switch has power.
Per 10/100Mbps Port
LED Color Function
LNK/ACT Green
Light: Indicate the link through that port is successfully
established at 10/100Mbps Full duplex mode.
Blink Slowly: Indicate the link through that port is
successfully established at 10/100Mbps
Half duplex mode.
Blink Fast: Indicate that the Switch is actively sending
or receiving data over that port.
PoE Orange Light: Indicate the port is providing 48V DC in-line
power.

10
Per 10/100/1000Mbps Port
LED Color Function
Speed Green
Light: Indicate the link through that port is successfully
established at 1000Mbps.
Blink Slowly: Indicate the link through that port is
successfully established at 100Mbps.
Off: Indicate the link through that port is successfully
established at 10Mbps.
LNK/ACT Green
Light: Indicate the link through that port is successfully
established
Blink: Indicate that the Switch is actively sending or
receiving data over that port.
2.2 Rear Panel
The rear panel of the FGSD-910P indicates an AC inlet power socket, which accepts
input power from 100 to 240V AC, 50-60Hz, 2A.
100~240V AC
50/60Hz, 2A max.
Figure 2-2: FGSD-910P Switch Rear Panel
Power
Notice
The device is a power-required device, meaning it will not work till
it is powered. If your networks should be active all the time, please
consider using UPS (Uninterrupted Power Supply) for your device.
It will prevent you from network data loss or network downtime. In
some area, installing a surge suppression device may also help to
protect your FGSD-910P from being damaged by unregulated
surge or current to the FGSD-910P or the power adapter.
Before start up
Before your installation begins, please refer to the following for your cabling:
10/100Base-TX (Port 1 to Port 8)
All 10/100Base-TX ports come with Auto-Negotiation capability. They automatically
support 100Base-TX and 10Base-T networks. Users only need to plug a working
network device into one of the 10/100Base-TX ports, and then turn on the FGSD-
910P. The port will automatically run in 10Mbps, 20Mbps, 100Mbps or 200Mbps
after negotiating with the connected device.