Planet GSD-1222VHP User manual

8-/16-/24-Port 10/100/1000T 802.3at PoE+
Gigabit SFP Ethernet Switch with Smart LCD
GSD-1222VHP/GSW-1820VHP/GSW-2620VHP
User’s Manual

Copyright
Copyright © 2018 by PLANET Technology Corp. All rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specically disclaims any warranties,
merchantability or tness for any particular purpose. Any software described
in this manual is sold or licensed "as is". Should the programs prove defective
following their purchase, the buyer (and not PLANET, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or
consequential damages resulting from any defect in the software. Further, PLANET
reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation to notify any person of such revision or
changes
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Trademarks
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all
environments and applications, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance, merchantability, or
tness for a particular purpose.
PLANET has made every eort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred. Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET assumes
no responsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in this
User’s Manual, and reserves the right to make improvements to this User’s Manual
and/or to the products described in this User’s Manual, at any time without notice.
If you nd information in this manual that is incorrect, misleading, or incomplete,
we would appreciate your comments and suggestions.

FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
WEEE Warning
To avoid the potential eects on the environment and human health as a
result of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should
understand the meaning of the crossed-out wheeled bin symbol. Do not
dispose of WEEE as unsorted municipal waste; WEEE should be collected
separately.
Revision
PLANET 8-/16-/24-Port 10/100/1000T 802.3at PoE+ Gigabit SFP Ethernet Switch
with Smart LCD User's Manual
Models: GSD-1222VHP, GSW-1820VHP, GSW-2620VHP
Revision: 3.0 (Dec., 2018)
Part No.: 2351-AK5070-002

Table of Contents
1. Introduction ............................................................................................... 5
1.1 Package Contents ................................................................................ 5
1.2 Product Description.............................................................................. 6
1.3 Features ............................................................................................10
1.4 Specications .....................................................................................12
2. Hardware Description.................................................................................15
2.1 Front Panel ........................................................................................15
2.1.1 LCD Monitor Indicators ..............................................................16
2.1.2 LED Indicators ..........................................................................17
2.2 Rear Panel .........................................................................................19
2.3 LCD Management ...............................................................................20
2.3.1 Switch Mode ...........................................................................21
2.3.2 Budget Control ........................................................................23
2.3.3 PSE Port Priority ......................................................................24
2.3.4 PSE Port Enable.......................................................................24
2.3.5 PD Type..................................................................................25
2.3.6 Alive Check .............................................................................26
2.3.7 Bandwidth Detection ................................................................27
2.3.8 Fan Control .............................................................................28
2.3.9 Screen Saver ..........................................................................28
2.3.10 Language................................................................................29
2.3.11 Default Setting ........................................................................29
2.3.12 System ...................................................................................29
3. Hardware Installation .................................................................................30
3.1 Desktop Installation ............................................................................31
3.2 Rack Mounting ...................................................................................32
3.3 Installing the SFP Transceiver ..............................................................33
3.4 Product Applications............................................................................35
3.5 Power over Ethernet Powered Devices ..................................................36
4. Power over Ethernet Overview ....................................................................37
5. Troubleshooting .........................................................................................40
Appendix A Networking Connection ..................................................................41
A.1 Switch's Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T ................41
A.2 10/100Mbps, 10/100BASE-TX ...............................................................41

5
1. Introduction
Thank you for purchasing PLANET 8/16/24-Port 10/100/1000T 802.3at PoE+ Gigabit
SFP Ethernet Switch series, GSD-1222VHP, GSW-1820VHP and GSW-2620VHP. The
descriptions of these models are shown below:
GSD-1222VHP 8-Port 10/100/1000T 802.3at PoE + 2-Port Gigabit SFP + 2-Port
Gigabit TP Ethernet Switch
GSW-1820VHP 16-Port 10/100/1000T 802.3at PoE + 2-Port Gigabit SFP Ethernet
Switch
GSW-2620VHP 24-Port 10/100/1000T 802.3at PoE + 2-Port Gigabit SFP Ethernet
Switch
“802.3at PoE+ Switch” is used as an alternative name in this user’s manual.
1.1 Package Contents
Open the box of the 802.3at PoE+ Switch and carefully unpack it. The box should
contain the following items:
802.3at PoE+ Switch x 1 User’s Manual x 1
Power Cord x 1 Screws Package x 1
Rack-mounting Brackets x 2 Rubber Feet x 4

6
If any of these pieces are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing material,
and use them again to repack the product in case there is a need to return it to us
for repair.
1.2 Product Description
Ideal High-performance Integration Solution for Secure IP Surveillance
Infrastructure
Particularly designed for the growing popular IP surveillance applications, PLANET
GSD/GSW 802.3at PoE+ Switch series is positioned as a surveillance switch with
the central power management and IP camera monitoring.
The GSD/GSW 802.3at PoE+ Switch series brings an ideal, secure surveillance
system at a lower total cost. The GSD/GSW 802.3at PoE+ Switch series provides
multiple 10/100/1000 Mbps 802.3at/af PoE ports able to supply sucient PoE
power to IEEE 802.3at PoE IP cameras at the same time. It is also able to be
connected with an 8-/16-/32-channel NVR system, uplinked to the backbone switch
and the monitoring center. With such a high-performance switch architecture, the
recorded video les from the PoE IP cameras can be saved in the NVR system to
enable the administrators to control and monitor the surveillance images both in
the local LAN and the remote sites.
Model GSD-1222VHP GSW-1820VHP GSW-2620VHP
10/100/1000T Copper 8 x RJ45 16 x RJ45 24 x RJ45
10/100/1000T Copper 2 x RJ45 -- --
1000X Fiber Optic 2 x SFP Slots 2 x SFP Slots 2 x SFP Slots
802.3af/at PoE+ Ports 816 24
PoE Budget 120 watts 300 watts 300 watts
Enclosure 12” metal case 19” metal case 19” metal case

7
Just “Plug and Watch” for a Quick Solution
The GSD/GSW 802.3at PoE+ Switch series is an ideal Plug and Watch Power over
Ethernet solution which provides quick installation, real-time PoE work status
monitoring and immediate troubleshooting through its unique LCD display to
improve work eciency and quality without any PC or software required.
The GSD/GSW 802.3at PoE+ Switch series is equipped with 8/16/24
10/100/1000BASE-T ports featuring 30-watt 802.3at Power over Ethernet Plus
(PoE+) copper interfaces. With a total PoE power budget of up to 300 watts and
non-blocking data switching performance, the GSD/GSW 802.3at PoE+ Switch
series fullls the demand of sucient PoE power for HD IP surveillance. It oers a
desktop-sized, reliable and visible power solution for small businesses and system
integrators deploying Power over Ethernet networks.
Smart LCD Power LED
Gigabit SFP
LNK/ACT Status
PoE & LNK/ACT
Status
Menu/Enter/Back
Up/Down Button
2 x Gigabit SFP
16 x 10/100/1000BASE-T 802.3at PoE+

8
Smart and Intuitive LCD Control
The GSD/GSW 802.3at PoE+ Switch series provides an intuitive color panel on its
front panel that facilitates the Ethernet management and PoE PD management.
They greatly promote management eciency in large-scale network, such as
enterprises, hotels, shopping malls, government buildings, and other public areas,
and feature the following special management and status functions:
PoE management and status
Port management and status
Switch Mode: Standard, VLAN, Extend
Budget and bandwidth control
PD alive check
Maintenance: Screen saver, fan control, factory default and save conguration
4 6 82
1 3 5 7
12 14 1610
911 13 15
GSW-1820VHP
1
PWR
Up
Down
Menu (5 sec)
Enter
Back
5 9 13
3 7 11 15
PoE
2 6 10 14
4 8 12 16
PoE
PoE In-Use
ACTLNK1000
ACTLNK10/100
ACT
LNK
SFP
17 18
SFP
17 18
16-Port 10/100/1000T 802.3at PoE +
2-Port Gigabit SFP Ethernet Switch
Switch Port Information
30.3
01 W ---M867M
----
02 W ---M---M
----W
03 ---M---M
15.4W
04 -10M---M
----W
05 ---M---M
----
06 W ---M---M
----
07 W ---M---M
----
08 W ---M---M
-8.3
09 W ---M-<1M
----
10 W ---M---M
-OFF
11 ----M---M
----
12 W ---M---M
17.6W
13 223M246M
----
14 W ---M---M
PB:300W TP:72W PD:0
Main Menu
01 —
02 —
03 —
05 —
06 —
07 —
08 —
Switch Mode
Budget Control
PSE Port Priority
PD Type
Alive Check
Bandwidth
Fan Control
04 — PSE Port Enable
System
<Back>: Return
PLANET 802.3af/at PoE Switch
www.planet.com.tw
Model: FGSW-2622VHP
HW ver: V2.0
SW ver: V3.01
PSE Port Enable
Port Status
>
Enable01
Disable
<UP>/<Down>:Select
<Enter>:Confirm <Back>:Return
Current Setting: Enable
Switch Mode
Options:
VLAN
Extend
Standard>

9
Standard, VLAN and Extend Operation Modes Oered
The GSD/GSW 802.3at PoE+ Switch series provides Standard, VLAN and Extend
operation modes. The GSD/GSW 802.3at PoE+ Switch series operates as a normal
IEEE 802.af/at PoE Switch in the Standard operation mode. The VLAN operation
mode features the port-based VLAN function that can help to prevent the IP
camera’s multicast or broadcast storm from inuencing each other.
VLAN Isolation Mode
Ports 17 and 18 for uplink
Ports 1~16 Access Permitted
GSW-1820VHP PC
Ports 1 to 16
Access Denied
PoE
PoE
PoE
1000
1000BASE-SX/LX Fiber-optic
1000
1000BASE-T UTP
PoE
1000BASE-T UTP with PoE
IP Camera
IP Camera
IP Camera
NVR
Standard
> VLAN
Extend
In the Extend operation mode, the GSD/GSW 802.3at PoE+ Switch series operates
on a per-port basis at 10Mbps duplex operation but can support 20-watt PoE
power output over a distance of up to 250 meters overcoming the 100m limit on
Ethernet UTP cable. With this brand-new feature, the GSD/GSW Series provides
an additional solution for 802.3af/at PoE distance extension, thus saving the cost
of Ethernet cable installation. Its VLAN isolation function isolates ports so as to
prevent broadcast storm and defend DHCP spoong in the Extend operation mode.
Standard Mode (default)
Power
PoE
100 meters (328 feet)
GSW-1820VHP
PoE
1000BASE-T UTP with PoE
PoE IP Camera
> Standard
VLAN
Extend
Extend Mode
Power
250 meters (820 feet)
PoE
GSW-1820VHP
PoE
10BASE-T UTP with PoE
PoE IP Camera
Standard
VLAN
> Extend

10
Flexible Extension Solution
The two mini-GBIC slots built in the GSD/GSW 802.3at PoE+ Switch series are
compatible with the 1000BASE-SX/LX SFP (Small Form-factor Pluggable)
ber transceiver, uplinked to the backbone switch and monitoring center in long
distance. The distance can be extended from 550 meters (multi-mode ber) to
10/20/30/40/50/60/70/120 kilometers (single-mode ber or WDM ber). They are
well suited for applications within the enterprise data centers and distributions.
Robust Protection
The GSD/GSW 802.3at PoE+ Switch series provides contact discharge of ±6KV DC
and air discharge of ±8KV DC for Ethernet ESD protection. It also supports ±6KV
surge immunity to improve product stability and protects users’ networks from
devastating ESD attacks, making sure the ow of operation does not uctuate.
Easy Installation and Cable Connection
As data and power are transmitted over one cable, the GSD/GSW 802.3at PoE+
Switch series does not need a second cable and electrical outlets on the wall,
ceiling or any unreachable place. Thus, it helps to lower the installation costs and
simplify the installation eort. All the RJ45 copper interfaces of the GSD/GSW
802.3at PoE+ Switch series support 10/100/1000Mbps auto-negotiation for optimal
speed detection through RJ45 Category 6, 5 or 5e cable. It also supports standard
auto-MDI/MDI-X that can detect the type of connection to any Ethernet device
without requiring special straight-through or crossover cables.
1.3 Features
Physical Port
GSD-1222VHP
8-port 10/100/1000BASE-T Gigabit RJ45 copper
2 1000BASE-X mini-GBIC SFP interfaces
2 10/100/1000BASE-T TP interfaces
GSW-1820VHP
16-port 10/100/1000BASE-T Gigabit RJ45 copper
2 1000BASE-X mini-GBIC SFP interfaces
GSW-2620VHP
24-port 10/100/1000BASE-T Gigabit RJ45 copper
2 1000BASE-X mini-GBIC SFP interfaces

11
Power over Ethernet
Complies with IEEE 802.3af/at Power over Ethernet end-span PSE
Up to 8/16/24 ports of IEEE 802.3af/at devices powered
Supports PoE Power up to 32 watts for each PoE port
Each port supports 52V DC power to PoE powered device (GSD-1222VHP)
120-watt PoE budget (GSD-1222VHP)
Each port supports 54V DC power to PoE powered device (GSW-1820VHP/
GSW-2620VHP)
300-watt PoE budget (GSW-1820VHP/GSW-2620VHP)
Auto detects powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m in standard mode and 250m in extend
mode
Smart LCD
The LCD switch features “Standard”, “VLAN” and “Extend” mode selection;
the “Extend” mode features 20-watt PoE transmission distance of 250m at
speed of 10Mbps and VLAN isolation
The LCD switch is able to isolate ports to prevent broadcast storm and defend
DHCP spoong
Power low-voltage, power over-voltage and PSE over-temperature protection
Screen saver, fan control, factory default and save conguration
PoE management
- Total PoE power budget control
- Per port PoE function enable/disable
- PoE port power feeding priority
- Per PoE port power limitation
- PD alive check
Switching
Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X
Flow control for full duplex operation and back pressure for half duplex
operation
9216bytes packet size
Integrates address look-up engine, supporting 8K absolute MAC addresses
IEEE 802.1Q VLAN transparency
Automatic address learning and address aging

12
Hardware
12/19-inch desktop size, 1U height, rack mountable
2-inch color LCD with smart management functions
LED indicators for system power, per port PoE ready and PoE activity, speed,
Link/Act
1/3 silent fans to provide stable and ecient power performance
Supports Energy-Ecient Ethernet (EEE) function (IEEE 802.3az)
Supports contact discharge of ±6KV DC and air discharge of ±8KV DC for
Ethernet ESD protection
Supports ±6KV surge immunity
1.4 Specications
Model GSD-1222VHP GSW-1820VHP GSW-2620VHP
Hardware Specications
802.3af/at PoE
Injector Port 816 24
10/100/1000BASE-T
MDI/MDIX Ports 816 24
10/100/1000BASE-T
MDI/MDIX Ports 2--
1000BASE-X SFP/
mini-GBIC Slots 2
Switch Architecture Store-and-Forward
Switch Fabric 24Gbps/
non-blocking
36Gbps/
non-blocking
52Gbps/
non-blocking
Switch
Throughput@64
bytes
18Mpps@64 bytes 26.8Mpps@64
bytes
38.7Mpps@64
bytes
MAC Address Table 8K entries
Maximum Frame
Size 9216 bytes
Flow Control IEEE 802.3x pause frame for full duplex; back pressure for
half duplex

13
LED Indicators
System:
Power (Green)
10/100/1000BASE-T RJ45 Interfaces:
10/100Mbps LNK/ACT (Red)
1000Mbps LNK/ACT (Green)
PoE-in-Use (Amber)
1000BASE-X SFP
Interfaces:
10/100Mbps LNK/
ACT (Red)
1000Mbps LNK/
ACT (Green)
1000BASE-X SFP Interfaces:
LNK/ACT (Green)
LCD Monitor (W x D) 40.6 x 30.5 mm, 2-inch
Buttons Menu, Enter, Back, Up and Down
Dimensions
(W x D x H)
180 x 280 x 44mm
(1U height)
233 x 440 x 44 mm
(1U height)
Enclosure Metal
Weight 1.8kg 3.4kg 3.5kg
Power Requirements AC 100~240V,
50/60Hz, 2.5A max. 100~240V AC, 50/60Hz, 5A max.
Power Consumption/
Dissipation
Max. 130
watts/446 BTU
Max. 330watts/1132 BTU
Thermal Fan 1 3
ESD Protection Contact discharge of ±6KV DC
Air discharge of ±8KV DC
Surge Protection ±6KV
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet/PSE
IEEE 802.3at Power over Ethernet Plus/PSE
PoE Power Supply
Type End-span
PoE Power Output Per port 52V-54V DC, 300mA. max. 15.4 watts (IEEE 802.3af)
Per port 52V-54V DC, 600mA. max. 30 watts (IEEE 802.3at)
Power Pin
Assignment 1/2 (+), 3/6 (-)
PoE Power Budget 120 watts 300 watts

14
Max. Number of
Class 2 PDs 816 24
Max. Number of
Class 3 PDs 816 23
Max. Number of
Class 4 PDs 411 11
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standards
Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab Gigabit 1000BASE-T
IEEE 802.3z Gigabit SX/LX
IEEE 802.3x Flow Control and Back Pressure
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3az Energy Ecient Ethernet (EEE)
Environment
Operating
Temperature: -10 ~ 60 degrees C
Relative Humidity: 10 ~ 90% (non-condensing)
* Temperature: < 40 degrees C; Humidity: < 90%
Temperature: > 40 degrees C; Humidity: < 50%
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 90% (non-condensing)

15
2. Hardware Description
These switches provide three dierent running speeds – 10Mbps, 100Mbps and
1000Mbps and automatically distinguish the speed of the incoming connection.
This section describes the hardware features of 802.3at PoE+ Switch. For easier
management and control of the 802.3at PoE+ Switch, familiarize yourself with its
display indicators and ports. Front panel illustrations in this chapter display the unit
LED indicators. Before connecting any network device to the 802.3at PoE+ Switch,
please read this chapter carefully.
2.1 Front Panel
The Front Panel of the 802.3at PoE+ Switch consists of 8/16/24 802.3af/at auto-
sensing 10/100/1000Mbps Ethernet RJ45 ports and 2 Gigabit TP/SFP ports. The
LCD monitor and LED Indicators are also located on the front panel of the 802.3at
PoE+ Switch.
GSD-1222VHP
1
PWR
5
3 7
PoE
911
10 12
2 6
4 8
8-Port 10/100/1000T 802.3at PoE +
2G TP + 2G SFP Ethernet Switch
ACTLNK
10/1001000
PoE-in-Use
4 6 82
1357
10
911 12
Mini-GBIC
Menu (5 sec)
Enter
Back
Up
Down
Switch Port Information
30.3
01 W ---M876 M17.6
07 W ---M--- M
----
02 W ---M--- M-8.3
08 W ---M-<1 M
----W
03 ---M--- M---
09 ---M--- M
15.4W
04 -10M--- M---
10 ---M--- M
----W
05 ---M--- M---
11 ---M--- M
-OFF
06 ----M--- M---
12 223M246 M
PB:120W TP:72W PD:4
Figure 2-1: GSD-1222VHP Switch Front Panel
4 6 82
1 3 5 7
12 14 1610
911 13 15
GSW-1820VHP
1
PWR
Up
Down
Menu (5 sec)
Enter
Back
5 9 13
3 7 11 15
PoE
2 6 10 14
4 8 12 16
PoE
PoE In-Use
ACTLNK1000
ACTLNK10/100
ACT
LNK
SFP
17 18
SFP
17 18
16-Port 10/100/1000T 802.3at PoE +
2-Port Gigabit SFP Ethernet Switch
Switch Port Information
30.3
01 W ---M-33 M
----
02 W ---M--- M
----W
03 ---M--- M
15.4W
04 -10M--- M
----W
05 ---M--- M
----
06 W ---M--- M
----
07 W ---M--- M
----
08 W ---M--- M
-8.3
09 W ---M-11 M
----
10 W ---M--- M
-OFF
11 ----M--- M
----
12 W ---M--- M
17.6W
13 -11M-12 M
----
14 W ---M--- M
PB:300W TP:72W PD:4
Figure 2-2: GSW-1820VHP Switch Front Panel
4 6 82
1 3 5 7
12 14 1610
911 13 15
20 22 2418
17 19 21 23
Menu (5 sec)
Enter
Back
SFP
17 18
1
PWR
Up
Down
5 9 13 17 21
3 7 11 15 19 23
PoE
2 6 10 14 18 22
4 8 12 16 20 24
PoE
PoE In-Use
ACTLNK1000
ACTLNK10/100
ACT
LNK
SFP
25 26
GSW-2620VHP
Switch Port Information
30.3
01 W ---M-33 M
----
02 W ---M--- M
----W
03 ---M--- M
15.4W
04 -10M--- M
----W
05 ---M--- M
----
06 W ---M--- M
----
07 W ---M--- M
----
08 W ---M--- M
-8.3
09 W ---M-11 M
----
10 W ---M--- M
-OFF
11 ----M--- M
----
12 W ---M--- M
17.6W
13 -11M-12 M
----
14 W ---M--- M
PB:300W TP:72W PD:4
Figure 2-3: GSW-2620VHP Switch Front Panel
Gigabit TP Interface
10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters.
Gigabit SFP Slots
1000BASE-SX/LX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver
module: From 550 meters (multi-mode ber) to 10/20/30/40/50/60/70/120 kilo-
meters (single-mode ber).

16
Smart LCD
The Smart LCD that is located on the front panel of the GSD-1222VHP, GSW-
1820VHP, GSW-2620VHP 802.3at PoE+ Switch provides “PoE Manage-
ment and Status”, “Switch Mode: Standard, VLAN, Extend”, “Budget
and Bandwidth Control”, “Screen Saver”, “Fan Control”, and “Factory
Default”.
2.1.1 LCD Monitor Indicators
The 802.3at PoE+ Switch has an LCD monitor designed for network administrator
who can easily obtain real-time per PoE port output watts information and system
status display, such as over voltage, low voltage, and PoE chipset over temperature
function. The details of each message on the LCD monitor are shown below:
GSD-1222VHP/GSW-1820VHP/GSW-2620VHP LCD Display
Power Low-voltage Protection Power Over-voltage Protection PSE Over-temperature Protection
30.3
01 W ---M---M
ULP
02 ---M---M
OLP
03 ---M---M
SCP
04 ---M---M
----W
05 ---M---M
13.6
06 W ---M---M
14.4
07 W ---M---M
----
08 W 877M---M
----
09 W ---M867M
-OFF
10 - ---M---M
----
11 W ---M---M
----
12 W ---M---M
----
13 W ---M---M
----
14 W ---M---M
PB:300W TP:0W PD:3
Switch Port Information
Switch Port Information
----
01 W --- M---M
----
02 W --- M---M
----W
03 ---M---M
----W
04 ---M---M
----W
05 ---M---M
----
06 W --- M---M
----
07 W --- M---M
----
08 W --- M---M
----
09 W --- M---M
----
10 W --- M---M
----
11 W --- M---M
----
12 W --- M---M
----
13 W --- M---M
----
14 W --- M---M
WARNING！
Main supply voltage
is High！
All ports had shut-
down.
PD:0PB:300W TP:0W
----
01 W --- M---M
----
02 W --- M---M
----W
03 ---M---M
----W
04 ---M---M
----W
05 ---M---M
----
06 W --- M---M
----
07 W --- M---M
----
08 W --- M---M
----
09 W --- M---M
----
10 W --- M---M
----
11 W --- M---M
----
12 W --- M---M
----
13 W --- M---M
----
14 W --- M---M
WARNING！
The PSE device is too
hot!
All ports had shut-
down.
Switch Port Information
PD:0PB:300W TP:0W
----
01 W --- M---M
----
02 W --- M---M
----W
03 ---M---M
----W
04 ---M---M
----W
05 ---M---M
----
06 W --- M---M
----
07 W --- M---M
----
08 W --- M---M
----
09 W --- M---M
----
10 W --- M---M
----
11 W --- M---M
----
12 W --- M---M
----
13 W --- M---M
----
14 W --- M---M
WARNING！
Main supply voltage
is low！
All ports had shut-
down.
Switch Port Information
PD:0PB:300W TP:0W
PD light load protection
PD overload protection
Short-circuit protection
PoE Usage
Network traffic
PoE OFF
Power Budget Total PoE
Output
Number of PDs
Note
1. The LCD screens of the GSD-1222VHP and GSW-1820VHP and
GSW-2620VHP are the same, except the number of ports and
port allocation.
2. The LCD screens of the GSD-1222VHP and GSW-1820VHP and
GSW-2620VHP will refresh every 15 seconds.
3. For details on LCD Management feature, please refer to “2.3
LCD Management”.

17
The detailed Smart LCD description of each item is shown below:
Parameters Description
30.3W
(example) It means the output power port of the PoE switch.
OLP It means the port is overloaded corresponding to the PSE, and
the port stops powering.
ULP
It means the port corresponding to the PSE is lightly loaded and
the port stops powering (When the current on the network is less
than 7.5mA, the PSE thinks the PD has been dialed out and the
port stops powering).
SCP It means the port corresponding to the PSE appears to be short-
circuited and the port stops powering.
OFF It means the white and blue OFF shows that the port is blocked
by the menu command.
---W It means the port is without a PD device insert.
---M It means this port does not have data transfers.
<1M It means this port data rate transfers less than 1M.
877M
(example)
The white and blue character represents the data transmission
rate while the red character represents the data transmission rate
which is greater than the bandwidth setting, causing power to
restart the PSE port. If the resumption situation happens for 10
times within 1 hour, the power supply to the port will be cut o.
PB It means power budget.
TB It means total PoE power output information.
PD The number of PDs inserted.
2.1.2 LED Indicators
System
LED Color Function
PWR Green Lights to indicate that the Switch has power.

18
10/100/1000Mbps PoE Ports
LED Color Function
LNK/ACT Green
Lights Indicates the link through that port is successfully
established at 10/100/1000Mbps.
Blinks Indicates that the Switch is actively sending or
receiving data over that port.
PoE-in-Use Amber
Lights Indicates the port is providing DC in-line power.
O Indicates the connected device is not a PoE
powered device (PD).
1000Mbps SFP Slot
LED Color Function
LNK/
ACT Green
Lights Indicates the port is successfully established at 1000Mbps.
Blinks Indicates that the Switch is actively sending or receiving
data over that port.
1000 Green Lights Indicates the port is successfully established at 1000Mbps.
1000Mbps TP Slot (GSD-1222VHP)
LED Color Function
LNK/
ACT Green
Lights Indicates the link through that port is successfully
established at 1000Mbps.
Blinks Indicates that the Switch is actively sending or receiving
data over that port.
10/100 Red Lights Indicates the port is successfully established at
10/100Mbps
1000 Green Lights Indicates the port is successfully established at
1000Mbps.
1000Mbps TP Slot (GSW-1820VHP/GSW-2620VHP)
LED Color Function
LNK/
ACT Green
Lights Indicates the link through that port is successfully
established at 1000Mbps.
Blinks Indicates that the Switch is actively sending or receiving
data over that port.
10/100 Red Lights Indicates the port is successfully established at
10/100Mbps
1000 Green Lights Indicates the port is successfully established at
1000Mbps.

19
2.2 Rear Panel
The rear panel of the 802.3at PoE+ Switch has an AC power socket (100 to 240V
AC, 50-60Hz, 2.5/5A).
100-240V AC
50/60Hz, 2.5A
Figure 2-4: GSD-1222VHP Switch Rear Panel
100~240V AC 50/60Hz, 5A max.
Figure 2-5: GSW-1820VHP/GSW-2620VHP Switch Rear Panel
AC Power Receptacle
For compatibility with electrical outlet standard in most areas of the world, the
802.3at PoE+ Switch’s power supply automatically adjusts to line power in the
range of 100-240V AC and 50/60Hz, 2.5/5A.
Plug the female end of the power cord rmly into the receptacle on the rear panel
of the 802.3at PoE+ Switch and the other end into an electrical outlet, and the
power will be ready.
Power
Notice
The device is a power-required device, which means it will not
work till it is powered. If your networks should be active all the
time, please consider using UPS (Uninterrupted Power Supply) for
your device. It will prevent you from network data loss or network
downtime. In some areas, installing a surge suppression device
may also help to protect your 802.3at PoE+ Switch from being
damaged by unregulated surge or current to the Switch or the
power adapter.

20
2.3 LCD Management
The operation of the 5 buttons (Menu, Enter, Back, Up and Down) on the panel:
Up
Down
Menu (5 sec)
Enter
Back
Switch Port Information
30.3
01 W ---M867M
----
02 W ---M---M
----W
03 ---M---M
15.4W
04 -10M---M
----W
05 ---M---M
----
06 W ---M---M
----
07 W ---M---M
----
08 W ---M---M
-8.3
09 W ---M-<1M
----
10 W ---M---M
-OFF
11 ----M---M
----
12 W ---M---M
17.6W
13 223M246M
----
14 W ---M---M
PB:300W TP:72W PD:4
Press the menu button to switch the “Switch Port Information”.
Press the menu button for about 5 seconds and enter the Main Menu. Choose
a menu item by scrolling up and down, and press the “Enter” key to get to the
menu item you have chosen. Press the “Back” key to return to the previous
menu.