Planet IGS-4215 Series User manual

Industrial 4-/8-/16-Port 10/100/1000T + 2-Port
100/1000X SFP Managed Gigabit Ethernet Switch
IGS-4215 series
Quick Installation Guide

Table of Contents
1. Package Contents...................................................................... 3
2. Requirements............................................................................ 4
3. Wiring the Power Inputs ............................................................ 5
4. Terminal Setup (IGS-4215-16T2S only) ....................................... 7
4.1 Logging on to the Console................................................... 8
 4.2 ConguringIPAddressviatheConsole................................. 9
 4.3 StoringCurrentSwitchConguration ...................................11
4.4 SSH Login (IGS-4215-8T2S and IGS-4215-4T2S) .................12
5. Starting Web Management ........................................................13
 5.1 LoggingintotheIndustrialManagedSwitch ........................14
 5.2 SavingCongurationviatheWeb........................................16
6. RecoveringBacktoDefaultConguration ...................................17
7. Customer Support ....................................................................19

3
1. Package Contents
Thank you for purchasing PLANET Industrial L2/L4 Managed Gigabit
EthernetSwitch,IGS-4215 series. The descriptions of these models are
asfollows:
Models 10/100/1000T
RJ45 Ports
100/1000X
SFP Ports
IGS-4215-4T2S 4 2
IGS-4215-8T2S 8 2
IGS-4215-16T2S 16 2
“Industrial Managed Switch” mentioned in this Quick Installation
GuidereferstotheIGS-4215series.
Openthebox oftheIndustrialManaged Switch and carefullyunpackit.
Theboxshouldcontainthefollowingitems:
IndustrialManaged
Switch x 1
QuickInstallation
Guidex1
Wall-mountPlate
w/Screwsx1Set
DIN-railBracket
w/Screwsx1 SFPDustCapx2 RJ45DustCap
16T2S x 17
8T2S x 8
4T2S x 4
If any item is found missing or damaged, please contact your local
resellerforreplacement.

4
2. Requirements
The Industrial Managed Switch provides local and remote login
interface for management purposes. The following equipment is
necessaryforfurthermanagement:
zWorkstations running Windows XP/2003/Vista/7/8/10/2008/10,
MAC OS X or later, Linux, UNIX, or other platforms are compatible
withTCP/IPprotocols.
zWorkstations are installed with Ethernet NIC (Network Interface
Card)
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-
RS232converter.
The above Workstations have been installed with terminal
emulator, such as Hyper Terminal included in Windows XP/2003,
putty or tera term.
Serial cable -- one end is attached to the RS232 serial port,
while the other ends to the RJ45 console port of the Industrial
ManagedSwitch.
zEthernet Port Connection
Network cables--Use standard network (UTP) cables with RJ45
connectors.
TheabovePCisinstalledwithWebbrowser.
Note
Itis recommended to useInternetExplorer8.0 or above
to access the Industrial Managed Switch. If the Web
interface of the Industrial Managed Switch is not acces-
sible, please turn off the anti-virus software or firewall
andthentryitagain.

5
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed Switch consists of one
terminal block connector within 6 contacts for two redundant power
inputs and fault alarm. Please follow the steps below to insert the
power wire.
1.Insert positive/negative DC power wires into contacts 1 and 2 for
Power1or5and6forPower2.
IGS-4215-16T2S
Fault
V1+ V2+
PWR2PWR1
Max. fault loading: 24V, 1A
DC Input: 12-48V , 1.5A max.
AC Input: 24V , 1A max.
1 2 3 4 5 6
Figure 3-1: IGS-4215-16T2S Inlet Power Socket
IGS-4215-8T2S
DC Input: 9-48V , 1A max.
AC Input: 24V
, 0.5A max.
Max. Fault Alarm Loading: 24V, 1A
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 3-2: IGS-4215-8T2S Inlet Power Socket

6
IGS-4215-4T2S
Max. Fault Alarm Loading: 24V, 1A
DC Input: 9-48V
, 1A max.
AC Input: 24V
, 0.6A max.
V1+ V2+
PWR1 PWR2Alarm
1 2 3 4 5 6
Figure 3-3: IGS-4215-4T2S Inlet Power Socket
2.Tighten the wire-clamp screws for preventing the wires from loos-
ening.
123456
V1+ V1- V2+ V2-
Power 1 Power 2
Note
The wire gauge for the terminal block should be in the
rangefrom12 to 24 AWG.
Note
1. The power input range is DC 12~48V for IGS-
4215-16T2S, DC 9~48V for IGS-4215-8T2S and IGS-
4215-4T2S.
2.Useone power input when using AC 24V.
Caution
PWR1andPWR2mustprovidethesame DC voltage
whileoperatingwithdualpowerinput.

7
4. Terminal Setup (IGS-4215-16T2S only)
Tocongurethesystem,connect aserialcabletoa COM port on a PC
ornotebookcomputer and to the RJ45 typeserial(console)portofthe
IndustrialManagedSwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Industrial Managed Switch Console Connectivity
A terminal program is required to make the software connection to the
IndustrialManagedSwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port
shouldbeconguredas:
zBaud:115200
zDatabits:8
zParity:None
zStopbits:1
zFlowcontrol:None

8
4.1 Logging on to the Console
Once the terminal has been connected to the device, power on the
IndustrialManagedSwitchandtheterminalwilldisplay“runningtesting
procedures”.Then,the followingmessageasks tologinusername and
password. The factory default user name and password are shown in
Figure4-1below.
Username:admin
Password:admin
Figure 4-1: Industrial Managed Switch Console Login Screen
The user can now enter commands to manage the Industrial Managed
Switch. For a detailed description of the commands, please refer to the
followingchapters.
Note
1.For security reason, please change and memorize
the new password after this first setup.
2.Only accept command in lowercase letter under
consoleinterface.

9
4.2 ConguringIPAddressviatheConsole
The Industrial Managed Switch is shipped with default IP address as
follows:
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the
IndustrialManagedSwitch,pleaseusetheproceduresasfollows:
Display of current IP address
1.Atthe“IGS-4215-16T2S#”prompt,enter“show ip”.
2.The screen displays the current IP address, subnet mask and
gatewayasshowninFigure4-2.
Figure 4-2: IP Information Screen

10
CongurationoftheIPaddress
1.Atthe“IGS-4215-16T2S #”prompt,enter“congure”.
2.At the “IGS-4215-16T2S (cong)#” prompt, enter the following
commandandpress<Enter>asshowninFigure4-3.
IGS-4215-16T2S(cong)# ip address 192.168.1.100 mask
255.255.255.0
IGS-4215-16T2S(cong)# ip default-gateway 192.168.1.254
The previous command would apply the following settings for the
IndustrialManagedSwitch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
Figure 4-3: Conguring IP Address Screen
3.RepeatStep1tocheckiftheIPaddresshaschanged.
If the IP is successfully congured, the Industrial Managed Switch will
apply the new IP address setting immediately. You can access
theWebinterface of theIndustrialManagedSwitch through thenewIP
address.