Planet GS-5220-8P2T2S User manual

L2+ Gigabit Ethernet Switch
GS-5220-8P2T2S
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
3.1 Logging on to Console ......................................................................... 6
 3.2 ConguringIPAddress......................................................................... 7
 3.3 StoringCurrentSwitchConguration..................................................... 9
4. Starting Web Management .........................................................................10
 4.1 LoggingontotheL2+ManagedPoE+Switch.......................................11
 4.2 SavingConguration...........................................................................13
5. RecoveringBacktoDefaultConguration.....................................................14
6. Customer Support ....................................................................................15

3
1. Package Contents
Thank you for purchasing PLANET L2+ 8-Port 10/100/1000T 802.3at PoE + 2-Port
10/100/1000T + 2-Port 100/1000X SFP Managed Switch, GS-5220-8P2T2S. “L2+
Managed PoE+ Switch” mentioned in this quick installation guide refers to the
GS-5220-8P2T2S.
Open the box of the L2+ Managed PoE+ Switch and carefully unpack it. The
boxshouldcontainthefollowingitems:
L2+ManagedPoE Switch x 1 QuickInstallation
Guidex1 Rack-mountingKits
RubberFeetx1set ACPowerCordx1 DB9 to RS232
Cable x 1 SFPDustCapx2
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zWorkstations running Windows XP/2003/2008/2012/Vista/7/8/10, MAC OS X or
later,Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard).
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such as
TeraTerm,PuTTYorHyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheL2+ManagedPoE+Switch.
zEthernet Port Connection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
TheabovePCisinstalledwithWebbrowser.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the L2+ Managed PoE+ Switch. If the Web interface of the L2+
Managed PoE+ Switch is not accessible, please turn off the anti-
virussoftwareorfirewallandthentryitagain.

5
3. Terminal Setup
Tocongure the system,connectaserial cabletoaCOMport onaPCornotebook
computerandtoDB9typeofserialportoftheL2+ManagedPoE+Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 3-1: L2+ Managed PoE+ Switch Console Connectivity
A terminal program, such as Tera Term or PuTTY, is required to make the software
connectiontotheL2+ManagedPoE+Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud:115200
zDatabits:8
zParity:None
zStopbits:1
zFlowcontrol:None
Figure 3-2: COM Port Conguration

6
3.1 Logging on to Console
Once the terminal is connected to the device, power on the L2+ Managed PoE+
Switch and the terminal will display “running testing procedures”. Then, the
following message asks to log in user name and password. The factory default
user name and password are shown as follows and the login screen in Figure 3-3
appears.
Username:admin
Password:admin
Figure 3-3: L2+ Managed PoE+ Switch Console Login Screen
Theuser can nowenter commands tomanage the L2+Managed PoE+Switch. For
adetaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1. For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

7
3.2 ConguringIPAddress
TheL2+ManagedPoE+SwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the L2+ Managed
PoE+Switch,pleaseusetheproceduresasfollows:
 Show the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure3-4.
Figure 3-4: IP Information Screen

8
 Conguring IP Address
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure3-5.
GS-5220-8P2T2S#congureterminal
GS-5220-8P2T2S(cong)#interfacevlan1
GS-5220-8P2T2S(cong-if-vlan)#ipaddress192.168.1.100255.255.255.0
Figure 3-5: Conguring IP Address Screen
The previous command would apply the following settings for the L2+ Managed
PoE+Switch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
4.Repeatstep1tocheckiftheIPaddresshaschanged.
If the IP is successfully congured, the L2+ Managed PoE+ Switch will apply the
new IP address setting immediately. You can access the Web interface of the L2+
ManagedPoE+SwitchthroughthenewIPaddress.

9
3.3 StoringCurrentSwitchConguration
In the L2+ Managed PoE+ Switch, the running conguration sequence running-
cong can be saved from the RAM to FLASH by “copy” command, so that the
running conguration sequence becomes the start-up conguration le, which is
calledcongurationsave.
Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 3-6: Saving Current Conguration Command Screen
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.

10
4. Starting Web Management
The following shows how to start up the Web Management of the L2+ Managed
PoE+ Switch. Note the L2+ Managed PoE+ Switch is congured through an
Ethernet connection. Please make sure the manager PC must be set to the same
IP subnet address.
For example, the default IP address of the L2+ Managed PoE+ Switch is
192.168.0.100, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 254, except 100), and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.100
Figure 4-1: IP Management Diagram