Planet WGS-4215-8P2S User manual

Industrial Wall-mount Managed Gigabit Ethernet Switch
WGS-804HPT
WGS-4215-8T/WGS-4215-8T2S/WGS-4215-8P2S
WGS-4215-16P2S
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring the Power Inputs.............................................................................. 5
3.1 Terminal Block Connector Pinout ........................................................... 6
3.2 DC Power Jack .................................................................................... 6
4. Hardware Installation .................................................................................. 7
4.1 Wall Mount Installation......................................................................... 7
4.2 Magnet Installation .............................................................................. 8
4.2.1 Magnet Installation of WGS-4215-16P2S ...................................... 8
4.3 DIN-rail Mount Installation ................................................................... 9
5. Web Login.................................................................................................11
5.1 Starting Web Management ..................................................................11
 5.2 SavingCongurationviatheWeb ........................................................14
6. Telnet Login ..............................................................................................15
 6.1 ConguringIPAddress........................................................................16
 6.2 StoringtheCurrent Switch Conguration ..............................................17
7. RecoveringBacktoDefaultConguration.....................................................18
8. Customer Support .....................................................................................19

3
1. Package Contents
Thank you for purchasing PLANET Industrial Wall-mount Managed Gigabit Switch,
WGS-804HPT and WGS-4215 series. The table below shows the models with the
number of ports:
Model Name 10/100/1000T
Copper Ports
802.3atPoE
Ports
100/1000 SFP Fiber
Optical Interface
WGS-4215-8T 8 – –
WGS-4215-8T2S 8 – 2
WGS-804HPT 8 4 –
WGS-4215-8P2S 8 8 2
WGS-4215-16P2S 16 16 2
In the following section, unless specied, the term “Wall-mount Managed
Switch” mentioned in this quick installation guide refers to the above models.
Open the box of the Wall-mount Managed Switch and carefully unpack it. The box
should contain the following items:
The Wall-mount Managed
Switch x 1
Quick Installation
Guide x 1 pc
3-pin Terminal Block
Connector x 1 pc
(Vary on the model)
DIN-rail Kit x 1 set Magnet Kit x 1 set Wall-mounted Kit x 1 set
RJ45 Dust Cap x 8 pcs SFP Dust Cap x 2 pcs
(x16 for WGS-4215-16P2S only) (WGS-4215-8T2S/WGS-4215-8P2S/
WGS-4215-16P2S only)
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstations are installed with Ethernet NIC (Network Interface Card)
zEthernetPortConnection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
Itis recommended touse Internet Explorer8.0 or aboveto access
the Wall-mount Managed Switch. If the Web interface of the Wall-
mount Managed Switch is not accessible, please turn off the anti-
virus software or firewall and then try it again.

5
3. Wiring the Power Inputs
The Wall-mount Managed Switch features a strong dual power input system
(terminal block and DC jack) incorporated into customer’s automation network to
enhance system reliability and uptime.
Power Input Range
Model
3-pin Terminal Block DC Jack
WGS-4215-8T 12~48VDC,24VAC 12~48VDC,24VAC
WGS-4215-8T2S 12~48VDC,24VAC 12~48V DC
WGS-804HPT 48~56V DC 48~56V DC
WGS-4215-8P2S 48~56V DC 48~56V DC
WGS-4215-16P2S 48~56V DC 48~56V DC
Note
Max power requirement also rely on the real site application.
10/100/1000BASE-T RJ45 Port
10/100/1000BASE-T RJ45 Port
3-pin Terminal Block
DC Plug-in

6
3.1 Terminal Block Connector Pinout
To install the 3-pin Terminal Block Connector on the Wall-mount Managed Switch,
simply follow the following steps:
Step 1: Insert positive DC power wire into V+, negative DC power wire into V-,
and grounding wire into Ground.
V+
V
-
Ground
Step 2: Tighten the wire-clamp screws for preventing the wires from loosening
and plug into the Wall-mount Managed switch.
Note
1.Thewiregaugeshouldbeintherangefrom12to24AWG.
2. The device must be grounded.
3.2 DC Power Jack
The WGS-804HPT/WGS-4215-8P2S/WGS-4215-16P2S requires DC 48V~56V
power input and WGS-4215-8T/WGS-4215-8T2S requires DC 12~48V power input.
Should you have the issue of power connection, please contact your local sales
representative.
2.1mm
DC Receptacle 2.1mm
DC receptacle is 2.1mm wide that conforms to the WGS-4215 series 2.1mm
DC jack's central post. Do not install any improper power adaptor

7
4. Hardware Installation
4.1 Wall Mount Installation
To install the Wall-mount Managed Switch on the wall, simply follow the following
steps:
Step 1: It is required 4 holes with 8mm diameter on the wall; the distance
between the 2 holes is 133mm (WGS-804HPT/WGS-4215-8T), 163mm
(WGS-4215-8T2S/WGS-4215-8P2S),230mm (WGS-4215-16P2S)andthe
line through them must be horizontal.
Step 2: Install a conductor pipe inside the board hole and ush the edge of the
conductor pipe with the wall surface.
Step 3: Screw the bolts into the conductor pipe. The Wall-mount Managed Switch
isbetweenboltsandconductorpipe,asshownbelow.
W
D
Vary on model
Distance (mm) 8-port 8+2S 16+2S
W133 163 230
D118 118 124

8
4.2 Magnet Installation
To install the Wall-mount Managed Switchonamagneticsurface, simply follow the
following diagram:
4.2.1 Magnet Installation of WGS-4215-16P2S
Step 1: There are six holes in front, using six sets of magnets to install. Please
refer to the following.
Step 2: Turntheswitchtotheback,thenscrewthemagnettothemiddlehole.
SYS
PWR
180W
240W
SFP
17
18
120W
60W
5 731
6 842
13 15119
14 161210
PoE
DC Input Range
48-56V
V+
Ground
SFP
17 18
WGS-4215-16P2S
Managed
Fiber
PoE+ Magnet Mounting
PoE-in-Use
LNK/ACT
PoE Usage
ACTLNK
ACTLNK
1000
100

9
Warning
Asthe magnetic mountingdoes not fixcompletely,whendeploying
the switch please be aware that the equipment will not fall or
break due to vibration or dragging.
Note
Please use the screw from the Magnet kit to avoid breaking the
device.
4.3 DIN-rail Mount Installation
The DIN-rail kit is included in the package. When the wall-mount application for the
Wall-mount Managed Switch needs to be replaced with DIN-rail application, please
refer to the following gures to screw the DIN-rail on the Wall-mount Managed
Switch.TohanguptheWall-mountManagedSwitch,followthestepsbelow:
Step 1: Screw the DIN-rail on the Wall-mount Managed Switch.

10
Step 2: Lightly insert the DIN-rail into the track.
1Push
2Click
Step 3: Check whether the DIN-rail is tightly on the track.