Planet IGSW-24040T User manual

Industrial L2+
20-Port 10/100/1000T + 4-Port TP/SFP Combo
Managed Ethernet Switch
IGSW-24040T
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring DC Power Inputs .............................................................................. 5
4. Terminal Setup ........................................................................................... 6
4.1 Logging on to Console ......................................................................... 7
 4.2 ConguringIPAddressviaConsole ....................................................... 8
5. Starting Web Management .........................................................................10
 5.1 LoggingintotheIndustrialManagedSwitch.........................................11
 5.2 SavingCongurationviaWeb ..............................................................14
6. RecoveringBacktoDefaultConguration.....................................................15
7. Customer Support .....................................................................................16

3
1. Package Contents
Thank you for purchasing PLANET Industrial L2+ Managed Ethernet Switch.
“Industrial Managed Switch” is used as an alternative name in this Quick
InstallationGuide.
Open the box of the Industrial Managed Switch and carefully unpack it. The box
shouldcontainthefollowingitems:
 TheIndustrialManagedSwitch x 1
 QuickInstallationGuide x 1
 DB9toRJ45ConsoleCable x 1
 Rubber Feet x 4
 RackMountAccessoryKit x 1
 ACPowerCord x 1
 SFP Dust Cap x 4
 RJ45DustCap x 25
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zWorkstations running Windows XP/2003/2008/2012/Vista/7/8/10/11, MAC OS X
orlater,Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard).
zSerialPortConnection(Terminal)
 The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
 The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003,puttyorteraterm.
 Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheIndustrialManagedSwitch.
zEthernetPortConnection
 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
Note
It is recommended to use Chrome 98.0.xxx or above to access the
Industrial Managed Switch. If the Web interface of the Industrial
Managed Switch is not accessible, please turn off the anti-virus
softwareorfirewallandthentryitagain.

5
3. Wiring DC Power Inputs
The 6-contact terminal block connector on the front panel of the Industrial
ManagedSwitchis usedfortwo DCredundantpower input.Pleasefollow thesteps
below to insert the power wires.
1.Insert positive/negative DC power wires into contacts 1 and 2 for DC Power 1,
or5and6forDCPower2.
RingRing
AlarmAlarm I/OI/O
ACAC
DC1DC1
R.O.R.O.DC2DC2
AlarmAlarmDC1 DC2
DC POWER
ON
OFF
DC Input: 36-60V , 0.7A max.
100- 240V ~, 0.5A max.
50/60 HzOFF
ON
AC POWER
GNDGNDDO 1DO 0DI 1DI 0
Max. Fault Alarm Loading: 24V, 1A
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
1 2 3 4 5 6
V1+ V1- V2+ V2-
Power 1 Power 2
Positive(+)Pin Negative(-)Pin
IGSW-24040T Pin1/5 Pin2/6
Note
The wire gauge for the terminal block should be in the range
between12and24AWG.

6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type of serial port of the Industrial Managed
Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Industrial Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Industrial
ManagedSwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Databits:8
Parity:None
Stopbits:1
Flowcontrol:None
Figure 4-2: COM Port Conguration

7
4.1 Logging on to Console
Once the terminal is connected to the device, power on the Industrial Managed
Switchandtheterminalwilldisplay“runningtestingprocedures”.
Then, the following message asks to log in user name and password. The factory
default user name and password are shown as follows and the login screen in
Figure4-3appears.
Username:admin
Password:admin
Figure 4-3: Industrial Managed Switch Console Login Screen
The user can now enter commands to manage the Industrial Managed Switch. For
adetaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new
passwordafterthisfirstsetup.
2.Only accept command in lowercase letter under console
interface.

8
4.2 ConguringIPAddressviaConsole
TheIndustrialManagedSwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
DisplayingthecurrentIPAddress
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure4-4.
Figure 4-4: IP Information Screen
ConguringIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure4-5.
IGSW-24040T# congure terminal
IGSW-24040T(cong)# interface vlan 1
IGSW-24040T(cong-if-vlan)# ip address 192.168.1.100 255.255.255.0

9
The previous command would apply the following settings for the Industrial
ManagedSwitch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
Figure 4-5: Conguring IP Address Screen
4.RepeatStep1tocheckiftheIPaddresshaschanged.
Storingcurrentswitchconguration
5.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 4-6: Saving Current Conguration Command Screen
If the IP is successfully congured, the Industrial Managed Switch will apply the
new IP address setting immediately. You can access the Web interface of the
IndustrialManagedSwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.

10
5. Starting Web Management
The following shows how to start up the Web Management of the Industrial
Managed Switch. Note the Industrial Managed Switch is congured through an
Ethernet connection. Please make sure the manager PC must be set to the same
IP subnet address.
For example, the default IP address of the Industrial Managed Switch is
192.168.0.100, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 254, except 100), and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 5-1: IP Management Diagram